Full throttle Electric Supercharger Build Thread - Page 411 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

mid_life_crisis · 05-27-2014, 06:54 PM

Quote:

Originally Posted by Winjr

I thought the car's ECU needs to "cycle" through its complete analysis, which varies by car and is usually 20-30 miles worth of driving. Which means that the CEL won't light again immediately after start up, depending upon the problem, but will once the ECU completes its cycle. No?

It takes that long for the ECU to decide to clear a cel on its own. It can decide to trip one pretty much instantly. It does the driver no good to learn of a potential problem long after the damage is done.

shif7i7down · 05-27-2014, 07:05 PM

http://datazap.me/u/shif7i7down9188/...1-3-7-10-11-12

log of my 4th gear pull , does it look weird

Robftss · 05-27-2014, 07:18 PM

Quote:

Originally Posted by shif7i7down

http://datazap.me/u/shif7i7down9188/...1-3-7-10-11-12

log of my 4th gear pull , does it look weird

Boost/AFR look spot on.

robwbright · 05-27-2014, 07:38 PM

Quote:

Originally Posted by robwbright

Here's a log from today with 2nd and 3rd gear pulls.

http://datazap.me/u/robwbright/esc-l...log=0&data=1-7

How's it look?

What's up with my boost? It never reaches 4.

shif7i7down · 05-27-2014, 07:39 PM

The car feels awesome even with the cel. I wouldn't mind it if i could just have it deleted so it won't show up <-but I'm not sure if that's the best solution.

fenton · 05-27-2014, 07:50 PM

Quote:

Originally Posted by shif7i7down

I want to rule out Any possible mistake that i may have done to get the P0108 cel.

That rubber tube that connects to the aluminum peice"brass fitting" connects to the little black nub that is sticking out of the controller right?

If all else fails should i buy a new map sensor?
I'll also do some loggs later today

Make sure everything is tight?

Also you will probably get above 4 below 3000 rpm.

What is your altitude?

shif7i7down · 05-27-2014, 07:53 PM

Quote:

Originally Posted by fenton

Make sure everything is tight?

Also you will probably get above 4 below 3000 rpm.

What is your altitude?

Altitude is About 600ft.

Robftss · 05-27-2014, 07:54 PM

Quote:

Originally Posted by robwbright

What's up with my boost? It never reaches 4.

(ROB) RPM PSI (SHIF7) RPM PSI

N/A.... N/A_____ 3563 4.50
4016 3.92_____ 4280 3.92
5660 3.05_____ 5624 3.05
7063 1.82_____ 7104 1.89

They are the same.

robwbright · 05-27-2014, 08:38 PM

Quote:

Originally Posted by Robftss

(ROB) RPM PSI (SHIF7) RPM PSI

N/A.... N/A_____ 3563 4.50
4016 3.92_____ 4280 3.92
5660 3.05_____ 5624 3.05
7063 1.82_____ 7104 1.89

They are the same.

Got it - he just engaged at a lower rpm.

shif7i7down · 05-27-2014, 09:00 PM

can someone check their Phantom tune with Romraider and tell me what their Manifold Pressure Sensor is set at for High and Low input.

I was just curious and took a look at the phantom tune and mines set at 3.91 for high and .61 for low,

I was thinking that maybe if i up my volts for the high to something like 4.91 to see if that'll help with the p0108 code i'm having.

Sojhinn · 05-27-2014, 09:02 PM

Quote:

Originally Posted by shif7i7down

can someone check their Phantom tune with Romraider and tell me what their Manifold Pressure Sensor is set at for High and Low input.

I was just curious and took a look at the phantom tune and mines set at 3.91 for high and .61 for low,

I was thinking that maybe if i up my volts for the high to something like 4.91 to see if that'll help with the p0108 code i'm having.

@shiv@vishnu any help?

fenton · 05-27-2014, 09:02 PM

Quote:

Originally Posted by shif7i7down

can someone check their Phantom tune with Romraider and tell me what their Manifold Pressure Sensor is set at for High and Low input.

I was just curious and took a look at the phantom tune and mines set at 3.91 for high and .61 for low,

I was thinking that maybe if i up my volts for the high to something like 4.91 to see if that'll help with the p0108 code i'm having.

I'll check tonight. Can you link me to the software

shif7i7down · 05-27-2014, 09:11 PM

the software and the frs xml are on the openflashtablet website under download section

I honestly think that 3.91v is too low for 5psi boost -_-..

UPDATE: P0108 cel code is solved with a higher voltage limit.. i set it to 4.91 and no more cel. yeeaahh me. ^_^

fenton · 05-27-2014, 09:53 PM

Quote:

Originally Posted by shif7i7down

the software and the frs xml are on the openflashtablet website under download section

I honestly think that 3.91v is too low for 5psi boost -_-..

UPDATE: P0108 cel code is solved with a higher voltage limit.. i set it to 4.91 and no more cel. yeeaahh me. ^_^

How come it was at so low?

05-27-2014, 07:05 PM	#5742
shif7i7down Erected Member Join Date: Mar 2014 Drives: frs Location: Wisconsin Posts: 391 Thanks: 69 Thanked 185 Times in 100 Posts Mentioned: 10 Post(s) Tagged: 0 Thread(s)	http://datazap.me/u/shif7i7down9188/...1-3-7-10-11-12 log of my 4th gear pull , does it look weird __________________ https://www.facebook.com/profile.php?=87912848

05-27-2014, 07:39 PM	#5745
shif7i7down Erected Member Join Date: Mar 2014 Drives: frs Location: Wisconsin Posts: 391 Thanks: 69 Thanked 185 Times in 100 Posts Mentioned: 10 Post(s) Tagged: 0 Thread(s)	The car feels awesome even with the cel. I wouldn't mind it if i could just have it deleted so it won't show up <-but I'm not sure if that's the best solution. __________________ https://www.facebook.com/profile.php?=87912848

05-27-2014, 09:00 PM	#5750
shif7i7down Erected Member Join Date: Mar 2014 Drives: frs Location: Wisconsin Posts: 391 Thanks: 69 Thanked 185 Times in 100 Posts Mentioned: 10 Post(s) Tagged: 0 Thread(s)	can someone check their Phantom tune with Romraider and tell me what their Manifold Pressure Sensor is set at for High and Low input. I was just curious and took a look at the phantom tune and mines set at 3.91 for high and .61 for low, I was thinking that maybe if i up my volts for the high to something like 4.91 to see if that'll help with the p0108 code i'm having. __________________ https://www.facebook.com/profile.php?=87912848

05-27-2014, 09:11 PM	#5753
shif7i7down Erected Member Join Date: Mar 2014 Drives: frs Location: Wisconsin Posts: 391 Thanks: 69 Thanked 185 Times in 100 Posts Mentioned: 10 Post(s) Tagged: 0 Thread(s)	the software and the frs xml are on the openflashtablet website under download section I honestly think that 3.91v is too low for 5psi boost -_-.. UPDATE: P0108 cel code is solved with a higher voltage limit.. i set it to 4.91 and no more cel. yeeaahh me. ^_^ __________________ https://www.facebook.com/profile.php?=87912848 Last edited by shif7i7down; 05-27-2014 at 09:38 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Circuit Motorsports - Vortech Supercharger FR-S Build + Full Perrin Exhaust & Extras	Circuit Motorsports	Member's Car Journals	4	03-21-2013 05:45 PM
Subaru BRZ : Full Throttle, powerslide, hard revving & ride	ESBjiujitsu	BRZ Photos, Videos, Wallpapers, Gallery Forum	20	05-30-2012 07:43 PM
86 Full Throttle Video + another.	Aus86	FR-S & 86 Photos, Videos, Wallpapers, Gallery Forum	2	04-02-2012 08:07 AM

User Name		Remember Me?
Password