Full throttle Electric Supercharger Build Thread

[shif7i7down]

Originally Posted by fenton

Does the code come up when wot or when just starting the car.

Comes on when wot.

Btw, i dont need a 4bar map sensor do i?

[s2d4]

Originally Posted by robwbright

Which makes my CELs yesterday even weirder. They aren't there while driving the car to dads, the car is turned off for 5 minutes, the three CELs show up on restart, I drive 1/2 a mile, turn off the car, clear the CELs, restart the car, and all three of the CELs are gone. They didn't come back the two other times I started/drove the car later in the evening.

Do you have the OFT plugged in?

[robwbright]

Originally Posted by s2d4

Do you have the OFT plugged in?

Not on that occasion... I had the bluetooth OBD thing plugged in with Torque Pro running.

That did occur to me as a possible cause for the Network/Electrical CEL.

[fenton]

Originally Posted by shif7i7down

Comes on when wot.

Btw, i dont need a 4bar map sensor do i?

You do not need 4 BAR. The 1.5 the car comes with works fine for our application (5 psi and below).

I am very intrigued as to why you are getting that error when WOT as it would seem that CEL trigger is not excluded from the ROM or something like that.

[shif7i7down]

Originally Posted by fenton

You do not need 4 BAR. The 1.5 the car comes with works fine for our application (5 psi and below).

I am very intrigued as to why you are getting that error when WOT as it would seem that CEL trigger is not excluded from the ROM or something like that.

Idk, maybe @shiv@vishnu can answer that one

[s2d4]

Originally Posted by robwbright

Not on that occasion... I had the bluetooth OBD thing plugged in with Torque Pro running.

That did occur to me as a possible cause for the Network/Electrical CEL.

Yeap.

[Khyron686]

Got my 1.5 kit on Sat - need to make time this week to install it!

Finished OFH install, RCE yellows, and spyder headlights + wheel change.

Still not sure where I'm going to mount the display.

[jpit]

Rob,

I'm pretty the U0073 code is a problem with your OBD reader and the torque app. Every once in awhile I get this code even when it is communicating properly and others on this forum have experienced it also. This isn't a code I would worry about.

[Winjr]

Originally Posted by robwbright

Which makes my CELs yesterday even weirder. They aren't there while driving the car to dads, the car is turned off for 5 minutes, the three CELs show up on restart, I drive 1/2 a mile, turn off the car, clear the CELs, restart the car, and all three of the CELs are gone. They didn't come back the two other times I started/drove the car later in the evening.

I thought the car's ECU needs to "cycle" through its complete analysis, which varies by car and is usually 20-30 miles worth of driving. Which means that the CEL won't light again immediately after start up, depending upon the problem, but will once the ECU completes its cycle. No?

[shif7i7down]

I want to rule out Any possible mistake that i may have done to get the P0108 cel.

That rubber tube that connects to the aluminum peice"brass fitting" connects to the little black nub that is sticking out of the controller right?

If all else fails should i buy a new map sensor?
I'll also do some loggs later today

[Sojhinn]

Originally Posted by shif7i7down

I want to rule out Any possible mistake that i may have done to get the P0108 cel.

That rubber tube that connects to the aluminum peice"brass fitting" connects to the little black nub that is sticking out of the controller right?

If all else fails should i buy a new map sensor?
I'll also do some loggs later today

I've been thinking about this and I think you may have loosened a tube under boost. Check this out just in case.

http://www.ft86club.com/forums/showt...26#post1655426

[robwbright]

No CELs today... running fine and fast.

[raven1231]

Originally Posted by shif7i7down

I want to rule out Any possible mistake that i may have done to get the P0108 cel.

That rubber tube that connects to the aluminum peice"brass fitting" connects to the little black nub that is sticking out of the controller right?

If all else fails should i buy a new map sensor?
I'll also do some loggs later today

you're correct sir

[shif7i7down]

Originally Posted by Sojhinn

I've been thinking about this and I think you may have loosened a tube under boost. Check this out just in case.

http://www.ft86club.com/forums/showt...26#post1655426

dang, i gotta take that intake plastic manifold thingy off?