|
||||||
| Issues | Warranty | Recalls / TSB Problems, issues, recalls, TSBs |
 |
|
|
Thread Tools | Search this Thread |
10-30-2022, 02:26 AM
|
#1 |
|
Junior Member
Join Date: Aug 2019
Drives: Toyota 86gt
Location: Sydney
Posts: 8
Thanks: 0
Thanked 9 Times in 4 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Flex Fuel Gauge only reading while idling
Recently my flex fuel gauge has been playing up, it was working for an entire year previous to this.
The only thing I can think of that may have caused it was I was driving around looking for e85 and may have run the tank all the way to the bottom line of the petrol gauge before I filled up. Lately 5 sec after start up there is some hesitation of a second and also randomly there is like a brief timing pull? (not sure but it burbles and pops a little and hesitates). I also thought it could be dirty fuel, but I refilled half the tank with some premium 98ron from Shell (best available petrol in OZ) but it still has the same issue. So basically when the car is idling it reads the flex fine: But then when the car revs (past around 2k rpm), it doesn't show anymore: When the revs drop and it *resets* it goes like this: Before eventually reading the ethanol content again Has anyone else encountered this before? |
|
|
|
10-30-2022, 02:48 PM
|
#2 |
|
30 minute maintenance
Join Date: Oct 2020
Drives: My18 wrxsti
Location: Botany Bay
Posts: 1,178
Thanks: 769
Thanked 1,236 Times in 631 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
I`m sure mine reads constant. If the sensor is faulty it could be giving bad readings to the ecu. If its the display it probably wont matter. i dont know what sensor to read on the ecu. With the torque obd2 app its not ethanol content.
Maybe in here http://zeitronix.com/Products/ECA/EC...structions.pdf Last edited by gen3v8; 10-30-2022 at 03:08 PM. |
|
|
|
| The Following User Says Thank You to gen3v8 For This Useful Post: | NoHaveMSG (10-30-2022) |
|
10-30-2022, 05:09 PM
|
#3 |
|
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,564
Thanks: 18,845
Thanked 16,848 Times in 7,662 Posts
Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
|
The diagram @gen3v8 posted the FF sensor output is the green wire. It's a 0-5vdc output. Check the voltage output and see if it is dropping out with revs or holding steady. Not knowing the scaling for the ethenol compensation table can't tell you what voltage should be for your ethenol content but it should be a pretty steady output. Though according to the pdf it should be about 2.2vdc.
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
Last edited by NoHaveMSG; 10-30-2022 at 05:22 PM. |
|
|
|
|
10-31-2022, 08:25 PM
|
#4 |
|
Junior Member
Join Date: Aug 2019
Drives: Toyota 86gt
Location: Sydney
Posts: 8
Thanks: 0
Thanked 9 Times in 4 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Ah bloody silly of me. I was playing around with the manifold and forgot to tighten down the grounding bolt that is off the connection to the O2 sensor for FF...all is working as per normal again.
Thanks gents |
|
|
|
| The Following 5 Users Say Thank You to malkduds For This Useful Post: | DarkPira7e (10-31-2022), NoHaveMSG (10-31-2022), Tcoat (11-01-2022), WildCard600 (10-31-2022), x808drifter (11-01-2022) |
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| PTuning Flex fuel kit and AEM oil pressure gauge | endless_pain | Engine, Exhaust, Bolt-Ons | 2 | 12-14-2022 11:54 AM |
| Flex Fuel Gauge and Boost Control based on Ethanol Content | DeliciousTuning | Forced Induction | 6 | 10-11-2022 06:37 PM |
| Can an Ecutek tune influence what flex fuel gauge reads? | kev0 | Software Tuning | 25 | 04-18-2021 03:32 AM |
| Fuel Gauge - Incorrect Level Reading | soulreapersteve | Issues | Warranty | Recalls / TSB | 0 | 08-31-2016 12:28 AM |
| Fuel gauge not reading properly | FR-S Hot Lava | Issues | Warranty | Recalls / TSB | 27 | 10-29-2014 11:33 AM |
