Will this fit? (width, offset and tire size Qs) - Page 112 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

jshadeck · 06-26-2013, 04:43 PM

Yea i bought 5mm spacers to throw on at the first site of rubbing. But if they didnt rub after the last 2000 miles the way i drive, they wont ever lol

Drzdude · 06-28-2013, 05:55 PM

For Enkei RS05RR's running in 18x8.5 front and 18x9.5 back what offset and tire size is recommended? How much should the car be lowered front and back. Thanks!
---
18x8.5 +32 with 225/40/18
18x9.5 +39 with 255/35/18
with KW V3 coilovers ?
or like
18x8.5 +40 front with 225/40/18
18x9.5 +40 rear with 255/35/18

AutismIsAKiller · 07-07-2013, 07:59 PM

Looking at the Volk TE37RT wheels I am going to buy them individually so I can use all of one size or stagger them if it's needed. I am also willing to used wheel spacers
of whatever size is needed. They are....
17x9.5 +40 offset
18x10 +44 offset
What size tires I am about 1.5 inch lowered and I don't mind stretching for them to fit?

orod35 · 07-09-2013, 06:30 PM

i just bought a set of 17x8 oz superleggera rims. et 35 all around. will this be ok on my frs? stock height. also how can i find out personally for futre reference

ill86 · 07-09-2013, 07:01 PM

Quote:

Originally Posted by orod35

i just bought a set of 17x8 oz superleggera rims. et 35 all around. will this be ok on my frs? stock height. also how can i find out personally for futre reference

Yes, it will be OK.

Future reference = read this thread and grab a measuring device and/or online calculator.

ill86 · 07-09-2013, 07:05 PM

Quote:

Originally Posted by AutismIsAKiller

Looking at the Volk TE37RT wheels I am going to buy them individually so I can use all of one size or stagger them if it's needed. I am also willing to used wheel spacers
of whatever size is needed. They are....
17x9.5 +40 offset
18x10 +44 offset
What size tires I am about 1.5 inch lowered and I don't mind stretching for them to fit?

If you're buying wheels , buy the correct width / offset and skip the spacer.

Tires for 9.5" and 10" can be found by reading or searching this thread.

ill86 · 07-09-2013, 07:08 PM

Quote:

Originally Posted by Drzdude

For Enkei RS05RR's running in 18x8.5 front and 18x9.5 back what offset and tire size is recommended? How much should the car be lowered front and back. Thanks!
---
18x8.5 +32 with 225/40/18
18x9.5 +39 with 255/35/18
with KW V3 coilovers ?
or like
18x8.5 +40 front with 225/40/18
18x9.5 +40 rear with 255/35/18

You answered your own question. ^

For additional info please

adprokid · 07-09-2013, 08:04 PM

Why this thread isn't sticky anymore ?!

loogs · 07-09-2013, 08:36 PM

Quote:

Originally Posted by Lee358

So i put on my rpf1 17x9 +45 today... Is is safe that the tire is so close to the coil?..............

exactly what i have. its okay as long as its not touching. my coils arrive next week so i wont have to worry anymore.

plus, on full wheel lock, my rims hot the tie rod. you should have that same problem so keep the full wheel turn to a minimum

mashal · 07-09-2013, 11:13 PM

Will this be a flush fit? Running stock suspension just looking for a little fill.
Don't know much about tires and wheels

NorseLegend · 07-09-2013, 11:29 PM

I'm pretty sure I've done my math right this time;

Work Meister SR1 Standard 5x100, 18x9.5 -20 w/ 255/35r18, all corners

Looking for about 2in/50mm poke in in back, little bit more is going to be up front, lowered half an inch, no more than an inch though.

Anyone know what that would be like?

djdnz · 07-10-2013, 12:27 AM

Quote:

Originally Posted by mashal

Will this be a flush fit? Running stock suspension just looking for a little fill.
Don't know much about tires and wheels

The wheels will be 13mm more flush than stock, but not "flush" To achieve a flush with these wheels look you will need a 10mm spacer in the front and 15mm in the back. The tires are very large for our cars, 5% error in your spedometer and higher effective gearing.

Stock green, your proposed setup orange (ignore the suspension in the picture, it is not reflective of our cars):

ill86 · 07-10-2013, 12:52 AM

Quote:

Originally Posted by mashal

Will this be a flush fit? Running stock suspension just looking for a little fill.
Don't know much about tires and wheels

Wheel selection, OK. Will fill a bit but def not poke.

Tires included with wheels, bad selection for 86. Tire is too tall. 225/40 is a better choice.

ill86 · 07-10-2013, 12:58 AM

Quote:

Originally Posted by NorseLegend

I'm pretty sure I've done my math right this time;

Work Meister SR1 Standard 5x100, 18x9.5 -20 w/ 255/35r18, all corners

Looking for about 2in/50mm poke in in back, little bit more is going to be up front, lowered half an inch, no more than an inch though.

Anyone know what that would be like?

9.5 -20
Rough estimate :
70mm-75mm front poke
50-60mm rear poke

06-26-2013, 04:43 PM	#1555
jshadeck Senior Member Join Date: Nov 2012 Drives: 2013 Scion FR-S Whiteout 6MT Location: carlisle, pa Posts: 773 Thanks: 3 Thanked 221 Times in 163 Posts Mentioned: 9 Post(s) Tagged: 0 Thread(s)	Yea i bought 5mm spacers to throw on at the first site of rubbing. But if they didnt rub after the last 2000 miles the way i drive, they wont ever lol __________________

06-28-2013, 05:55 PM	#1556
Drzdude Member Join Date: Jun 2013 Drives: 2014 Subaru Wrx Location: Bensalem, PA Posts: 18 Thanks: 1 Thanked 3 Times in 3 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	For Enkei RS05RR's running in 18x8.5 front and 18x9.5 back what offset and tire size is recommended? How much should the car be lowered front and back. Thanks! --- 18x8.5 +32 with 225/40/18 18x9.5 +39 with 255/35/18 with KW V3 coilovers ? or like 18x8.5 +40 front with 225/40/18 18x9.5 +40 rear with 255/35/18 Last edited by Drzdude; 06-28-2013 at 06:42 PM.

07-07-2013, 07:59 PM	#1557
AutismIsAKiller Junior Member Join Date: Jul 2013 Drives: 2013 FR-S Location: Oklahoma City, Ok Posts: 3 Thanks: 0 Thanked 0 Times in 0 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Looking at the Volk TE37RT wheels I am going to buy them individually so I can use all of one size or stagger them if it's needed. I am also willing to used wheel spacers of whatever size is needed. They are.... 17x9.5 +40 offset 18x10 +44 offset What size tires I am about 1.5 inch lowered and I don't mind stretching for them to fit? Last edited by AutismIsAKiller; 07-07-2013 at 08:51 PM. Reason: Added Info

07-09-2013, 11:13 PM	#1564
mashal DADA Join Date: Jun 2012 Drives: 2013 Location: Kanada Posts: 1,500 Thanks: 47 Thanked 388 Times in 249 Posts Mentioned: 10 Post(s) Tagged: 0 Thread(s)	Will this be a flush fit? Running stock suspension just looking for a little fill. Don't know much about tires and wheels Attached Images

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Determining the proper width size of the tire	CyberFormula	Wheels \| Tires \| Spacers \| Hub -- Sponsored by The Tire Rack	49	05-23-2014 10:11 AM
Correct tire width for each wheel width	DarrenDriven	Wheels \| Tires \| Spacers \| Hub -- Sponsored by The Tire Rack	10	08-16-2012 03:03 PM
TIRE SIZE CALCULATOR	White64Goat	Wheels \| Tires \| Spacers \| Hub -- Sponsored by The Tire Rack	6	08-15-2012 03:31 AM
Tire Width vs Wheel Width	Synack	Wheels \| Tires \| Spacers \| Hub -- Sponsored by The Tire Rack	40	08-13-2012 12:21 AM

07-09-2013, 06:30 PM	#1558
orod35 Member Join Date: Jun 2013 Drives: silver 2013 scion frs Location: jacksonville, NC Posts: 15 Thanks: 1 Thanked 0 Times in 0 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	i just bought a set of 17x8 oz superleggera rims. et 35 all around. will this be ok on my frs? stock height. also how can i find out personally for futre reference

07-09-2013, 08:04 PM	#1562
adprokid Senior Member Join Date: Dec 2010 Drives: ZN6 / GDB-G Location: Far Posts: 589 Thanks: 710 Thanked 263 Times in 133 Posts Mentioned: 0 Post(s) Tagged: 1 Thread(s)	Why this thread isn't sticky anymore ?!

07-09-2013, 11:29 PM	#1565
NorseLegend A Very Annoying Person Join Date: Feb 2013 Drives: Subaru Impreza :( Hopefully BRZ Location: VA Posts: 285 Thanks: 234 Thanked 83 Times in 68 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	I'm pretty sure I've done my math right this time; Work Meister SR1 Standard 5x100, 18x9.5 -20 w/ 255/35r18, all corners Looking for about 2in/50mm poke in in back, little bit more is going to be up front, lowered half an inch, no more than an inch though. Anyone know what that would be like?

User Name		Remember Me?
Password