0 offset Works XD9 (allmost) - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

hypermax · 12-19-2012, 01:04 PM

Guys I have a set of Works XD9, they were previously for my 350z so the offset is really crazy on the BRZ, Front is 18x9 +22mm, Rear is 18x10 +18, what I have to do is get the 15mm lug conversion spacer from Project Kics and install them to all four corners, The original offset of the wheels will become near 0, FML.

Spacers will arrive tomorrow, I will see how bad this 0 offset is. The thing is I don't want to give up the wheels they are really nice.

when it is done, the car will look like an UFO, which it is pretty much against the will of the car, he was meant for handling.

Or I have to get get the wide body kit to fit the wheels

ill roller · 12-19-2012, 01:18 PM

Give up now... With camber you could make it work if you didn't need the adapters, but that extra 15mm is going to take it too far.

dorifuto · 12-19-2012, 01:29 PM

Don't do it!

hypermax · 12-19-2012, 03:44 PM

Quote:

Originally Posted by dorifuto

Don't do it!

LMAO, this is what i have in mind with the spacers, Front will fit good, but the rear will sticks out so hard

jserman · 12-19-2012, 03:48 PM

I would like to see a test fit with them just to see how much they stick out...

Walla Walla · 12-19-2012, 03:52 PM

had 0 offset rims on my supra a while ago... liked it a lot, but don't think it will fit on the twins.

hypermax · 12-19-2012, 04:02 PM

Quote:

Originally Posted by jserman

I would like to see a test fit with them just to see how much they stick out...

Yeah, I will do test fit for sure, I don't to give up now jet. I have to see this UFO in person to give the project.

larryw · 12-19-2012, 05:31 PM

Front might work with a butt load of camber. And I mean A LOT. About 6 degrees give or take. Rear isn't going to work. Sorry buddy. For reference, the car below has a 18x10 +12 set up in front, 18x10.5 +17 w/ in the rear, with TONS of camber. He also says he has a lot of clearance issues. I don't know if it would be worth putting the rims on.

hypermax · 12-19-2012, 05:46 PM

Quote:

Originally Posted by larryw

Front might work with a butt load of camber. And I mean A LOT. About 6 degrees give or take. Rear isn't going to work. Sorry buddy. For reference, the car below has a 18x10 +12 set up in front, 18x10.5 +17 w/ in the rear, with TONS of camber. He also says he has a lot of clearance issues. I don't know if it would be worth putting the rims on.

Very nice info to know, it is very helpful, and it does hurt my feeling.

finch1750 · 12-19-2012, 07:50 PM

Rocketbunny?

dorifuto · 12-19-2012, 07:59 PM

I have a set of factory r33 gtr rims I wanna run. With a conversion spacer it would be 17x9+15. Does anybody have pics of this fitment on a brz/frs?

RazorHawk · 12-19-2012, 08:14 PM

Quote:

Originally Posted by larryw

Front might work with a butt load of camber. And I mean A LOT. About 6 degrees give or take. Rear isn't going to work. Sorry buddy. For reference, the car below has a 18x10 +12 set up in front, 18x10.5 +17 w/ in the rear, with TONS of camber. He also says he has a lot of clearance issues. I don't know if it would be worth putting the rims on.

If it wasnt dropped to the floor I think this would look pretty good. I think that he should go ahead with it, and see how it works out. The pics above are pretty flush or barely poking a bit, and I bet the clearance issues are more from the drop than the rims themselves.

jserman · 12-19-2012, 08:38 PM

Larryw that frs is pimp

jumbaco · 12-20-2012, 01:43 PM

how did you come up with the zero offset?

Front is 18x9 +22mm, Rear is 18x10 +18, with 15mm spacer, you will now have 18x9+7, 18x10 +3

12-19-2012, 01:04 PM	#1
hypermax Senior Member Join Date: Dec 2012 Drives: BRZ Limited Location: FL Posts: 156 Thanks: 15 Thanked 73 Times in 44 Posts Mentioned: 7 Post(s) Tagged: 0 Thread(s)	0 offset Works XD9 (allmost) Guys I have a set of Works XD9, they were previously for my 350z so the offset is really crazy on the BRZ, Front is 18x9 +22mm, Rear is 18x10 +18, what I have to do is get the 15mm lug conversion spacer from Project Kics and install them to all four corners, The original offset of the wheels will become near 0, FML. Spacers will arrive tomorrow, I will see how bad this 0 offset is. The thing is I don't want to give up the wheels they are really nice. when it is done, the car will look like an UFO, which it is pretty much against the will of the car, he was meant for handling. Or I have to get get the wide body kit to fit the wheels Last edited by hypermax; 12-19-2012 at 03:47 PM.

12-19-2012, 01:18 PM	#2
ill roller Senior Member Join Date: Sep 2012 Drives: BRZ/E30/IS300/LS400 Location: Chicago Posts: 293 Thanks: 25 Thanked 306 Times in 104 Posts Mentioned: 9 Post(s) Tagged: 0 Thread(s)	Give up now... With camber you could make it work if you didn't need the adapters, but that extra 15mm is going to take it too far. __________________ RISKY DEVIL // ILL PHOTOGRAHY

12-19-2012, 07:50 PM	#10
finch1750 Undisputed El Presidente Join Date: Jun 2012 Drives: Zenki 37J ZN6 Location: Stockton, CA Posts: 11,594 Thanks: 9,404 Thanked 9,411 Times in 5,270 Posts Mentioned: 374 Post(s) Tagged: 33 Thread(s)	Rocketbunny? __________________ "Just like how a strut bar somehow enables you to corner 20MPH faster around a cloverleaf on-ramp, when the reality is, you can do it already but you just don't have to balls to do it." - CSG David

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
So, what's the stock offset?	rogerdalien	Wheels \| Tires \| Spacers \| Hub -- Sponsored by The Tire Rack	34	12-17-2018 10:47 PM
offset is everything	notFRS	Wheels \| Tires \| Spacers \| Hub -- Sponsored by The Tire Rack	24	04-11-2017 02:52 PM
37 vs 45 offset - Advan RS	Symbiont	Wheels \| Tires \| Spacers \| Hub -- Sponsored by The Tire Rack	18	03-28-2014 12:12 PM
Offset for GT vs. GTS	giraffee	AUSTRALIA	3	07-20-2012 12:30 AM
deep offset	jdmboss86	Wheels \| Tires \| Spacers \| Hub -- Sponsored by The Tire Rack	6	06-28-2012 10:12 PM

12-19-2012, 01:29 PM	#3
dorifuto If in doubt,flat out Join Date: Oct 2012 Drives: 2013 brz Location: colorado Posts: 260 Thanks: 56 Thanked 211 Times in 75 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Don't do it!

12-19-2012, 03:48 PM	#5
jserman Member Join Date: Dec 2012 Drives: 97 DB8 Location: Boise Posts: 24 Thanks: 0 Thanked 4 Times in 4 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	I would like to see a test fit with them just to see how much they stick out...

12-19-2012, 05:31 PM	#8
larryw Member Join Date: Jun 2012 Drives: - Location: - Posts: 55 Thanks: 98 Thanked 142 Times in 26 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Front might work with a butt load of camber. And I mean A LOT. About 6 degrees give or take. Rear isn't going to work. Sorry buddy. For reference, the car below has a 18x10 +12 set up in front, 18x10.5 +17 w/ in the rear, with TONS of camber. He also says he has a lot of clearance issues. I don't know if it would be worth putting the rims on.

12-19-2012, 07:59 PM	#11
dorifuto If in doubt,flat out Join Date: Oct 2012 Drives: 2013 brz Location: colorado Posts: 260 Thanks: 56 Thanked 211 Times in 75 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	I have a set of factory r33 gtr rims I wanna run. With a conversion spacer it would be 17x9+15. Does anybody have pics of this fitment on a brz/frs?

12-19-2012, 08:38 PM	#13
jserman Member Join Date: Dec 2012 Drives: 97 DB8 Location: Boise Posts: 24 Thanks: 0 Thanked 4 Times in 4 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Larryw that frs is pimp

12-20-2012, 01:43 PM	#14
jumbaco Senior Member Join Date: Jun 2012 Drives: FD Location: socal Posts: 176 Thanks: 31 Thanked 45 Times in 40 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	how did you come up with the zero offset? Front is 18x9 +22mm, Rear is 18x10 +18, with 15mm spacer, you will now have 18x9+7, 18x10 +3

User Name		Remember Me?
Password