|
BRZ Second-Gen (2022+) -- General Topics General topics for the second-gen BRZ |
|
Thread Tools | Search this Thread |
12-15-2021, 07:24 PM | #1 |
Member
Join Date: Jun 2013
Drives: 2020 BRZ PP
Location: West Palm Beach, FL
Posts: 90
Thanks: 18
Thanked 15 Times in 12 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Spacer sizes???
Just bought my 2022 today. Should arrive (out of state) on Friday.
Already have suspension ready for it. In the short term, until I figure out my wheel and tire setup would like to put spacers on the car. Anyone have an idea of sizing?? |
12-15-2021, 08:17 PM | #2 |
Junior Member
Join Date: Nov 2021
Drives: VW
Location: Canada
Posts: 9
Thanks: 0
Thanked 3 Times in 3 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
I intend to install 10mm in the front and 15mm on the back (slip-on spacers). Since i don't want bolt-ons spacers. Need ARP extended studs too.
|
The Following User Says Thank You to Mathmk7r For This Useful Post: | Yoshoobaroo (12-16-2021) |
12-16-2021, 12:20 AM | #3 |
Member
Join Date: Jan 2014
Drives: 2022 BRZ Premium
Location: New Orleans, LA
Posts: 81
Thanks: 2
Thanked 22 Times in 14 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
With the old car it was 20 and 25mm for flush fit. I'm not sure if that will be different on this new car though. I know the new wheels are a half inch wider, but I'm not sure if the track is wider. Hopefully someone can chime in on this.
|
12-16-2021, 06:57 AM | #4 |
TRACKBREAD
Join Date: Mar 2016
Drives: 2013 BRZ
Location: Florida
Posts: 3,929
Thanks: 2,660
Thanked 4,024 Times in 1,895 Posts
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
|
|
12-16-2021, 07:10 AM | #5 |
Member
Join Date: Jun 2013
Drives: 2020 BRZ PP
Location: West Palm Beach, FL
Posts: 90
Thanks: 18
Thanked 15 Times in 12 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Yes its been confirmed that the rear track of the car is wider but don’t have exacts. On my previous pp (7.5” wheel) brz I ran 25mm on all 4 corners (no poke).
|
02-09-2022, 04:25 PM | #6 |
Member
Join Date: Jun 2013
Drives: 2020 BRZ PP
Location: West Palm Beach, FL
Posts: 90
Thanks: 18
Thanked 15 Times in 12 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Ok so after messing about with a few different setups. I landed with a 30mm F (25mm F works as well but not as flush) and 20mm R.. Flush fitment. NO POKE!!
|
02-09-2022, 07:37 PM | #7 |
Member
Join Date: Nov 2021
Drives: 1997 BMW Z3 2.8, 2022 BRZ Premium
Location: NC
Posts: 42
Thanks: 1
Thanked 18 Times in 11 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
So in theory, for a flush fitment with stock wheels of 7.5" the fronts would have an offset of 18, and the rears and offset of 28?
|
02-10-2022, 06:36 AM | #8 |
Senior Member
Join Date: May 2015
Drives: '15 GT86 & '22 GR86
Location: Kent, UK
Posts: 146
Thanks: 37
Thanked 112 Times in 51 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
Nice, got any photos? I will be going down this route.
|
02-10-2022, 08:40 AM | #9 |
Junior Member
Join Date: Nov 2021
Drives: VW
Location: Canada
Posts: 9
Thanks: 0
Thanked 3 Times in 3 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Finally, i ordered 20mm at four corners. 25mm in the rear seems to poke a little.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
JDM Battery Sizes? | Roadcone | Electronics | Audio | NAV | Infotainment | 3 | 03-26-2018 03:14 PM |
Small spacer vs big spacer | Atomic Rooster | Wheels | Tires | Spacers | Hub -- Sponsored by The Tire Rack | 12 | 11-09-2017 01:30 PM |
Sprint Kit + RPF1 17x9+35 To spacer or not to spacer? | Khorne | Suspension | Chassis | Brakes -- Sponsored by 949 Racing | 4 | 07-03-2014 12:53 PM |
25mm conversion spacer with 5mm spacer = safe or unsafe? | deedz | Wheels | Tires | Spacers | Hub -- Sponsored by The Tire Rack | 1 | 05-05-2013 11:59 AM |