AIT relocation - Bias resistor values - HKS SC - ECUTEK - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Trap63 · 04-02-2019, 03:46 AM

Hi guys, I wish to relocate AIT from stock intake for a better evalution of temperature (pressure side) and a better timing management when idle or low speed.
I saw that Fensport manage a poor sensor "VE375083 Cambiare" and I prefer AEM 30-2014, more reliable and faster

https://www.aemelectronics.com/produ...ure-ait-sensor

30-2014: Air Temp Sensor with 1/8" NPT Male Thread, High Performance DTM-Style Connector, Aluminum Bung, Connector & Pins.

The big issue is that for the sensor sold by Fensport is known the right scaling to set in EcuTek table.
I asked for the AEM 30-2014 to Ecutek but they haven't the right Bias resistor value.
The answer was: "
Hi Gian,

I'm not entirely sure on what the Bias resistor the BRZ ECU uses but I do know the older Subarus used a 1000ohm Bias so I would suggest trying this scaling initially. "

These are specs of 30-2014

This is the relocation

Is there anyone who can confirm me the 1000Ohm value? or where to find this value?

Hags86 · 04-02-2019, 05:39 AM

Are you using the OEM wiring harness or wiring direct into the ECU?

Hags86 · 04-02-2019, 05:42 AM

Scratch that. Saw your photo of the wiring from the MAF sensor. Makes sense.

I'd be willing to bet its 1kOhm. Turn it on with the engine at room temp and that is a good sanity check.

But to know for sure wire in a 1k resistor rather than the sensor and measure the voltage. Assuming it's a 5V supply you'll see 2.5V or be able to figure it out if it isn't. If you get stuck I can look through the wiring diagram and help you work out what the ECU is doing.

Once you know you can set the ecutek table to suit any sensor you want.

Trap63 · 04-02-2019, 05:43 AM

I would wire to stock wiring, the first two wires you see as Fensport does.

Inviato dal mio SM-G960F utilizzando Tapatalk

Hags86 · 04-02-2019, 06:19 AM

Do you have a multimeter handy? I can walk you through the steps to check if you like.

Trap63 · 04-02-2019, 08:14 AM

Quote:

Originally Posted by Hags86

Do you have a multimeter handy? I can walk you through the steps to check if you like.

that's fine! as soon as I will receive from CA I'll do this check.

04-02-2019, 03:46 AM	#1
Trap63 Senior Member Join Date: Apr 2013 Drives: Brz WRB - Europe LHD Location: TURIN - Piedmont - ITALY Posts: 922 Thanks: 1,176 Thanked 839 Times in 289 Posts Mentioned: 40 Post(s) Tagged: 1 Thread(s)	AIT relocation - Bias resistor values - HKS SC - ECUTEK Hi guys, I wish to relocate AIT from stock intake for a better evalution of temperature (pressure side) and a better timing management when idle or low speed. I saw that Fensport manage a poor sensor "VE375083 Cambiare" and I prefer AEM 30-2014, more reliable and faster https://www.aemelectronics.com/produ...ure-ait-sensor 30-2014: Air Temp Sensor with 1/8" NPT Male Thread, High Performance DTM-Style Connector, Aluminum Bung, Connector & Pins. The big issue is that for the sensor sold by Fensport is known the right scaling to set in EcuTek table. I asked for the AEM 30-2014 to Ecutek but they haven't the right Bias resistor value. The answer was: " Hi Gian, I'm not entirely sure on what the Bias resistor the BRZ ECU uses but I do know the older Subarus used a 1000ohm Bias so I would suggest trying this scaling initially. " These are specs of 30-2014 This is the relocation Is there anyone who can confirm me the 1000Ohm value? or where to find this value? __________________

04-02-2019, 05:39 AM	#2
Hags86 Senior Member Join Date: Mar 2013 Drives: Toyota GTS 86 Location: Melbourne Australia Posts: 243 Thanks: 21 Thanked 118 Times in 65 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Are you using the OEM wiring harness or wiring direct into the ECU? __________________ 2013 Toyota 86: 275rwkW Coyoda Water-to-air Intercooled Turbo with GTX2863. CP Carillo Rods and Pistons. Motec M150 ECU. Motec C125 Dash. Holinger SG 6 Speed Sequential Gearbox. OS Giken LSD. MCA Reds Coilover. AP Racing Essex Sprint Front Brakes. PWR Radiator and Intercooler heat exchanger.

04-02-2019, 05:42 AM	#3
Hags86 Senior Member Join Date: Mar 2013 Drives: Toyota GTS 86 Location: Melbourne Australia Posts: 243 Thanks: 21 Thanked 118 Times in 65 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Scratch that. Saw your photo of the wiring from the MAF sensor. Makes sense. I'd be willing to bet its 1kOhm. Turn it on with the engine at room temp and that is a good sanity check. But to know for sure wire in a 1k resistor rather than the sensor and measure the voltage. Assuming it's a 5V supply you'll see 2.5V or be able to figure it out if it isn't. If you get stuck I can look through the wiring diagram and help you work out what the ECU is doing. Once you know you can set the ecutek table to suit any sensor you want. __________________ 2013 Toyota 86: 275rwkW Coyoda Water-to-air Intercooled Turbo with GTX2863. CP Carillo Rods and Pistons. Motec M150 ECU. Motec C125 Dash. Holinger SG 6 Speed Sequential Gearbox. OS Giken LSD. MCA Reds Coilover. AP Racing Essex Sprint Front Brakes. PWR Radiator and Intercooler heat exchanger.

04-02-2019, 05:43 AM	#4
Trap63 Senior Member Join Date: Apr 2013 Drives: Brz WRB - Europe LHD Location: TURIN - Piedmont - ITALY Posts: 922 Thanks: 1,176 Thanked 839 Times in 289 Posts Mentioned: 40 Post(s) Tagged: 1 Thread(s)	I would wire to stock wiring, the first two wires you see as Fensport does. Inviato dal mio SM-G960F utilizzando Tapatalk __________________

04-02-2019, 06:19 AM	#5
Hags86 Senior Member Join Date: Mar 2013 Drives: Toyota GTS 86 Location: Melbourne Australia Posts: 243 Thanks: 21 Thanked 118 Times in 65 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Do you have a multimeter handy? I can walk you through the steps to check if you like. __________________ 2013 Toyota 86: 275rwkW Coyoda Water-to-air Intercooled Turbo with GTX2863. CP Carillo Rods and Pistons. Motec M150 ECU. Motec C125 Dash. Holinger SG 6 Speed Sequential Gearbox. OS Giken LSD. MCA Reds Coilover. AP Racing Essex Sprint Front Brakes. PWR Radiator and Intercooler heat exchanger.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Omni 3bar map sensor values for ecutek	Agent_D	Software Tuning	9	07-17-2017 10:32 PM
Brake bias calculations for BBK	Fizz	Suspension \| Chassis \| Brakes -- Sponsored by 949 Racing	29	09-08-2015 02:50 PM
WTB: Used FRS DRL Resistor	FrostedFlakes	Want-To-Buy Requests	0	03-14-2015 03:41 AM
CHP bias	ndsleep612	Northern California	11	07-29-2013 12:05 AM
Bad gas, station bias?	Bg8780	Engine, Exhaust, Transmission	20	05-09-2013 03:52 PM

User Name		Remember Me?
Password