OpenFlash Tablet: OTS v2.0 Beta (132 new maps, 12 new XMLs) Available for Download

[Kodename47]

Originally Posted by lucid215

it was a wot log from 2800 rpms to about 7500 rpms. this was done in 3rd gear

What scaling did you try and do? That will only be open loop which has no impact on LTFT at all.

[lucid215]

Originally Posted by Kodename47

What scaling did you try and do? That will only be open loop which has no impact on LTFT at all.

ah gotcha. well damn then trying to figure out that javascript was for nothing haha what range of rpms should i be logging to try and scale the maf?

[Kodename47]

Originally Posted by lucid215

ah gotcha. well damn then trying to figure out that javascript was for nothing haha what range of rpms should i be logging to try and scale the maf?

Look at @steve99's signature, there's a link with good info.

[steve99]

Originally Posted by troek

im comparing tables and not seeing any differences other than a couple changes in low rpms in knock correction advance max A. were there no changes for 93 users? just toned down maps for 91?

Yes the 91/93 maps in v2 tunes only the one ignition table different, but many changes between v1.5x and V2 maps including Maf and fueling tables.

[solidONE]

Originally Posted by JB86'd

plugged in my OFT to take a datalog after a mellow freeway drive toward home..to my surprise my IAM was down at .7 already when I plugged it in. So I did a datalog anyway, and am seeing some Fuel Trim, FLKC and KC Learned values and am not sure that they're acceptable.
I now have about 100 miles on this tune, so I'm guessing it should be fully learned? Do I need to reflash and do something differently? Or is this just a result of California 91 Octane?

http://datazap.me/u/joshbustos86/frs...ata=1-6-8-9-12

Please help @steve99 @Shiv@Openflash

Actually gonna try the Vishnu Reset trick to get my IAM back up to 1 tomorrow and see if it helps.

What intake are you running? Curious since you seem to be logging higher MAF voltages than I am with a stage 1 tune.

[lucid215]

Originally Posted by Kodename47

Look at @steve99's signature, there's a link with good info.

Yea I've looked his stuff. Still trying to comprehend some of it haha

[JB86'd]

Originally Posted by solidONE

What intake are you running? Curious since you seem to be logging higher MAF voltages than I am with a stage 1 tune.

Stock intake, unmodified, AFE dryflow filter. You on the 2.0 maps?

[steve99]

Based on feedback for a few guys posting in this thread made some changes to the Knock correction thread to hopefully make it easier to understand

http://www.ft86club.com/forums/showthread.php?t=61820

[troek]

Originally Posted by steve99

Yes the 91/93 maps in v2 tunes only the one ignition table different, but many changes between v1.5x and V2 maps including Maf and fueling tables.

no i was talking about my 1.5 UEL map vs the 2.0 UEL 93. but i realised i was lookinig at one map with the incorrect xml file, since you cant load 2 xmls at once. ill have to figure out a different way to compare the tables.

[steve99]

Originally Posted by troek

no i was talking about my 1.5 UEL map vs the 2.0 UEL 93. but i realised i was lookinig at one map with the incorrect xml file, since you cant load 2 xmls at once. ill have to figure out a different way to compare the tables.

ROMRAIDER can load two tunes with different xml definitions. however the oft roms have had the calid,s changed so that the oft will load roms but it confuses romraider sometimes.

If you manually switch definition files each time you open a rom by making the correct xml the first or only one in list you can get around it. just make sure you have correct def in for a save or it might be nasty.

always best to re-open a saved rom and check the tables to be sure

[troek]

Originally Posted by steve99

ROMRAIDER can load two tunes with different xml definitions. however the oft roms have had the calid,s changed so that the oft will load roms but it confuses romraider sometimes.

If you manually switch definition files each time you open a rom by making the correct xml the first or only one in list you can get around it. just make sure you have correct def in for a save or it might be nasty.

always best to re-open a saved rom and check the tables to be sure

arigatou, sensei.

[clintavo]

Has anyone else noticed hesitation/ bogging at 1500 rpm when floored?

I realize this is a somewhat rare scenario, but I have run into it twice:
Loafing around a parking lot in 2nd gear, suddenly to get out of someone's way.
Starting from a stop uphill.

It is repeatable; floor it at 1500 rpm and it completely bogs. It never happened with 1.3 or 1.6

BTW the throttle calibration seems much smoother in this tune : )

Thanks Shiv!

[unsurety]

I can't tell what version the maps are on my tablet. How do I load the 2.0 maps onto the OFT?

Download the maps, unzip the maps folder into the Openflash folder?

[steve99]

Originally Posted by unsurety

I can't tell what version the maps are on my tablet. How do I load the 2.0 maps onto the OFT?

Download the maps, unzip the maps folder into the Openflash folder?

see OFT TIPS post below links to youtube tutorial