OpenFlash Tablet

[Tiremonkey0824]

Just installed the OFT and have a question. When I originally installed my borla uel I used a spacer on my o2 sensor to avoid a CEl. Would I need to remove this spacer now that the vehicle is tuned?

[Rombinhood@OpenFlash]

Originally Posted by Tiremonkey0824

Just installed the OFT and have a question. When I originally installed my borla uel I used a spacer on my o2 sensor to avoid a CEl. Would I need to remove this spacer now that the vehicle is tuned?

You shouldn't need to use any spacer with Vishnu's Stage 2 tune since it disables the catalyst inefficiency diagnostic routine in the ROM. But I don't see any harm in leaving it in there if you choose to.

[Plxdjake89]

Can I disable the tpms sensor light with this tablet?

[Rombinhood@OpenFlash]

Originally Posted by Plxdjake89

Can I disable the tpms sensor light with this tablet?

At this time, no.

[Plxdjake89]

Originally Posted by Rombinhood@OpenFlash

At this time, no.

Damn! Hopefully in time

Just finished installing this right now, didn't realize the launch control feature was active right away, lovin it!

Haven't gone for a test drive but hope to soon

[Tiremonkey0824]

Originally Posted by Plxdjake89

Damn! Hopefully in time

Just finished installing this right now, didn't realize the launch control feature was active right away, lovin it!

Haven't gone for a test drive but hope to soon

Are you using the stage 2 map? For some reason my tune does not have the launch control feature. Either that or it is set really high and I haven't revved high enough to find it.

[Plxdjake89]

Originally Posted by Tiremonkey0824

Are you using the stage 2 map? For some reason my tune does not have the launch control feature. Either that or it is set really high and I haven't revved high enough to find it.

I'm using the stg1 map, I believe mine is set to 5500 or so, go try it out the sound is addicting lol

I'm curious on how we set that up :/

[Tiremonkey0824]

Originally Posted by Plxdjake89

I'm using the stg1 map, I believe mine is set to 5500 or so, go try it out the sound is addicting lol

I'm curious on how we set that up :/

Just tried 2 step and FFS and i can confirm that the stage 2 map does not have either of these. I guess the guys running the stage 2 map are going to have to set it up themselves using Tunerpro.

[Rombinhood@OpenFlash]

Originally Posted by Tiremonkey0824

Just tried 2 step and FFS and i can confirm that the stage 2 map does not have either of these. I guess the guys running the stage 2 map are going to have to set it up themselves using Tunerpro.

The 2 step is indeed functional in the OTS maps. You can test this by free revving the engine in neutral with vehicle stopped. It will rev to 6000rpm and bounce rapidly.

FFS is not enabled in the OTS however because it doesn't make a good daily driving feature. You can enable it if you want to go drag racing though.

[Tiremonkey0824]

Originally Posted by Rombinhood@OpenFlash

The 2 step is indeed functional in the OTS maps. You can test this by free revving the engine in neutral with vehicle stopped. It will rev to 6000rpm and bounce rapidly.

FFS is not enabled in the OTS however because it doesn't make a good daily driving feature. You can enable it if you want to go drag racing though.

Man that is set pretty high up there. I'll have to bring it down some for myself, i dont like breaking axles.

[continuecrushing]

Is there a way to make the launch control only in effect when the clutch is pushed in? Right now I have launch control set at 4k, and I can't rev higher than that in neutral because of it. Obviously it's doing it's job, but some times I wanna rev the engine (testing new exhaust for example)

[RC51ed]

Originally Posted by Shutter

Is there a way to make the launch control only in effect when the clutch is pushed in? Right now I have launch control set at 4k, and I can't rev higher than that in neutral because of it. Obviously it's doing it's job, but some times I wanna rev the engine (testing new exhaust for example)

From what I was told. The 2 conditions for launch control with the oft works is that the car is under 10mph and the clutch is pressed. So maybe if you just leave it in neutral and don't press the clutch. You should be able to rev past the limiter.

[continuecrushing]

Originally Posted by RC51ed

From what I was told. The 2 conditions for launch control with the oft works is that the car is under 10mph and the clutch is pressed. So maybe if you just leave it in neutral and don't press the clutch. You should be able to rev past the limiter.

I'll try again, but after installing my ARK exhaust the other day, I went to rev the engine and was greeted by the awesome 4k rpm setting I currently have set for my launch control! Foot was not on the clutch, from my recollection haha. I'll try again tomorrow.

[1086]

Can the open flash tablet show horsepower and torque?