Rev works UEL Headers

[grostoine]

Originally Posted by ramiram1984

Not if it's resonated

You mean the headers?

[kuhlka]

Originally Posted by Grip Ronin

ive had them for maybe 4 months. good quality but i have a leak were the flanges meet the over pipe. bad angle or warped idk . they have offered to fix it but im debating shipping back again

Did you try loosening everything from the OP back, then tightening everything down from the header back? I suspect a lot of people just take off the headers and leave everything else tight when they go to install the header. The OP probably needs a bit of wiggling to mate up smoothly.

[Jolaessss]

OP Check out this thread... http://www.ft86club.com/forums/showthread.php?t=45434

[Grip Ronin]

Originally Posted by kuhlka

Did you try loosening everything from the OP back, then tightening everything down from the header back? I suspect a lot of people just take off the headers and leave everything else tight when they go to install the header. The OP probably needs a bit of wiggling to mate up smoothly.

i tryed it recently but on jack stands. maybe better on a lift and some exhaust silicone, its not too bad of a leak with oem gasket but its still there

[grostoine]

Can someone please post some photo's of the collector of the headers? I wanted to know if it looks more like borla or JDL...

[FT-86 SpeedFactory]

Originally Posted by grostoine

Can someone please post some photo's of the collector of the headers? I wanted to know if it looks more like borla or JDL...

Check our site.

We got the most complete photo sets for most products including the revworks.

IT's hard to get a good photo of due to the bend though.

[grostoine]

Originally Posted by FT-86 SpeedFactory

Check our site.

We got the most complete photo sets for most products including the revworks.

IT's hard to get a good photo of due to the bend though.

I just saw it but it's a bit unclear...

So I will ask you to give me your impressions please :P

[FT-86 SpeedFactory]

Originally Posted by grostoine

I just saw it but it's a bit unclear...

So I will ask you to give me your impressions please :P

It does have a better collector visually than the Borla.

[Noob4Life]

Originally Posted by FT-86 SpeedFactory

It does have a better collector visually than the Borla.

Couldn't get any worse lmao

Sent from my SAMSUNG-SM-N900A using Tapatalk

[The Racers Line]

Here's a cold start with my nameless axleback. My neighbor has a built rx7 tt and says my car sounds awesome in the mornings. Haha

[ame]http://m.youtube.com/watch?v=Yn_BVvbF7rY[/ame]

[grostoine]

The headers is ordered!

Can't wait to have it! It will complete my nameless axleback and OP/FP catted and resonated.

Does it give a clear Subaru UEL sound? I asked because it's not the most UEL headers i've seen!

[grostoine]

The headers is ordered!

Can't wait to have it! It will complete my nameless axleback and OP/FP catted and resonated.

Does it give a clear Subaru UEL sound? I asked because it's not the most UEL headers i've seen!

[The Racers Line]

Originally Posted by grostoine

The headers is ordered!

Can't wait to have it! It will complete my nameless axleback and OP/FP catted and resonated.

Does it give a clear Subaru UEL sound? I asked because it's not the most UEL headers i've seen!

They have a good rumble to them. Especially brought out with an exhaust. I've gotten many complements on the sound from subaru guys. The only car I've heard that sounded closer to an sti/Wrx was an Avo turbo and their manifold is very UEL.

[ame]http://m.youtube.com/watch?v=kCOQXP4gW4M[/ame]

[kuhlka]

I fixed my leak. Loosened the bolt hanging the front pipe and put some ultra copper (sensor safe RTV) on the gasket and tightened down the bolts evenly until they were güt'n'tite. Tightened the FP bolt and all's well. I'll do another video when the car is done tuning. Another later once I get the full Perrin on.