Official OpenFlash Tablet FA20 Tuning Tech Discussion Thread - Page 34 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Fizz · 10-24-2013, 12:53 PM

Quote:

Originally Posted by Anorax

Don't do that. You'll likely throw a CEL. Mine did the same (doors wouldn't lock) after the first read...

I'm guessing the OFT is somehow affecting the immobilizer? But any idea why?

Shiv@Openflash · 10-24-2013, 12:55 PM

Quote:

Originally Posted by Fizz

I'm guessing the OFT is somehow affecting the immobilizer? But any idea why?

This would be news to me

Shiv@Openflash · 10-24-2013, 12:56 PM

Quote:

Originally Posted by scarfo

sooooo E-85?

Been busy getting stg2 and international rom support rolling. And now I'll be out of town from Friday to Tuesday. So assuming there are no reported issues with stage 2 while I'm gone, e85 maps should be ready to launch towards the end of next week.

8686 · 10-24-2013, 01:48 PM

Quote:

Originally Posted by shiv@vishnu

Been busy getting stg2 and international rom support rolling. And now I'll be out of town from Friday to Tuesday. So assuming there are no reported issues with stage 2 while I'm gone, e85 maps should be ready to launch towards the end of next week.

so should I expect my rom support today or next week?

Calibration # ZA1J700K

Sent from my iPhone using Tapatalk - now Free

Shiv@Openflash · 10-24-2013, 01:57 PM

Quote:

Originally Posted by 8686

so should I expect my rom support today or next week?

Calibration # ZA1J700K

Sent from my iPhone using Tapatalk - now Free

Should be by the end of this week.

brn12345 · 10-24-2013, 03:31 PM

Quote:

Originally Posted by akyp

Only mods so far are TRD chassis stuff, brake lines and pads.

I think it's worth mentioning my ROM reading experience: After the reading was done, the doors wouldn't lock. After a few minutes of double-checking the doors and boot were properly shut, I switched back on the ignition then off, and now the doors would lock. For what it's worth my car has push-start button.

This happens to me and my car is stock. I don't think it has anything to do with the tune. I have to cycle the start button and then lock the doors again and it works. Noted it to the dealer on first inspection but they said its the first time they hear about this.

Shiv@Openflash · 10-24-2013, 05:49 PM

Quote:

Originally Posted by cjsporl

I tried to open the stg 2 BIN file into tunerpro to edit the launch control RPM and turn on flat foot shifting but it wont open.

Help Please.

Make sure you are running the latest version of Tuner Pro. You can download it off our website. The old version has the bug you are describing.

Shiv@Openflash · 10-24-2013, 06:53 PM

Quote:

Originally Posted by cjsporl

yea it was the one off your website

I updated the link just a few days ago. You probably have the old version.

My_First_Subaru · 10-24-2013, 06:57 PM

I'm pretty sure this has been covered already but I'm new to tuning and I was wondering that if I get this unit I can flash the ecu to stock when I go to the dealer and they wouldn't know it was tuned prior?

sierra · 10-24-2013, 07:01 PM

Quote:

Originally Posted by My_First_Subaru

I'm pretty sure this has been covered already but I'm new to tuning and I was wondering that if I get this unit I can flash the ecu to stock when I go to the dealer and they wouldn't know it was tuned prior?

Yes.

Robert@Openflash · 10-24-2013, 07:06 PM

If you have any questions and/or concerns please feel free to give us a call at 925.415.9148 and we will be able to assist you with the questions you may have. You can purchase this with confident and very little worries and a ton of fun. I guarantee you!!!

Quote:

Originally Posted by My_First_Subaru

I'm pretty sure this has been covered already but I'm new to tuning and I was wondering that if I get this unit I can flash the ecu to stock when I go to the dealer and they wouldn't know it was tuned prior?

Shiv@Openflash · 10-24-2013, 07:36 PM

Quote:

Originally Posted by cjsporl

just downloaded it an hour ago

I just tested in here on two computers and no such issue with Tuner Pro. Are you sure you are loading a 6MT ROM (ends with the letter C)?

Also, in Tuner Pro, go to Help->About and make sure you are running version 5.00.8200.00.

cnk · 10-24-2013, 08:19 PM

Open TunerPro
Click File -> Open Bin and select the BIN file
Click XDF -> Select XDF and select the XDF file

You should then be able to open up the tables on the left column.

Shiv@Openflash · 10-24-2013, 08:41 PM

Quote:

Originally Posted by cjsporl

Which of the two Xdf files do I use

The one that ends with ___C. That is for 6MTs.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
OpenFlash Tablet	Rombinhood@OpenFlash	Software Tuning	1838	07-29-2023 07:35 PM
OpenFlash Tablet Stg 2 Tune (Dyno Progress)	Rombinhood@OpenFlash	Software Tuning	26	10-24-2013 02:19 PM
FBM Tuning fixed my issue, FA20 and Visconti didn't work as well	whitefrs	Forced Induction	253	08-19-2013 01:39 PM
Official MMA Thread	zigzagz94	Off-Topic Lounge [WARNING: NO POLITICS]	11	12-15-2009 11:59 PM

10-24-2013, 06:57 PM	#471
My_First_Subaru Member Join Date: Oct 2013 Drives: SWP Subaru BRZ Location: san fernando valley Posts: 31 Thanks: 6 Thanked 6 Times in 3 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	I'm pretty sure this has been covered already but I'm new to tuning and I was wondering that if I get this unit I can flash the ecu to stock when I go to the dealer and they wouldn't know it was tuned prior?

10-24-2013, 08:19 PM	#475
cnk Senior Member Join Date: Aug 2012 Drives: '13 DGM BRZ Limited Location: NJ Posts: 1,201 Thanks: 59 Thanked 547 Times in 339 Posts Mentioned: 8 Post(s) Tagged: 0 Thread(s)	Open TunerPro Click File -> Open Bin and select the BIN file Click XDF -> Select XDF and select the XDF file You should then be able to open up the tables on the left column.

User Name		Remember Me?
Password