follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Delicious Tuning
Register Garage Members List Calendar Search Today's Posts Mark Forums Read

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Technical Topics > Tracking / Autocross / HPDE / Drifting

Tracking / Autocross / HPDE / Drifting What these cars were built for!

Register and become an FT86Club.com member. You will see fewer ads

User Tag List

Reply
 
Thread Tools Search this Thread
Old 12-01-2021, 10:07 PM   #1
noid
Junior Member
 
noid's Avatar
 
Join Date: Jun 2020
Drives: 2014 Subaru BRZ
Location: Bay Area
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Harness Mounting question

Hey all,



So I purchased a 6 point sparco harness that uses clips for the lap belt. I am using a PCI Racing seat plate which has a mounting hole for the tunnel side lap belt, and I'm hoping to use the stock seatbelt's mounting point for the outer side of the lap belt.



Is there a solution for this without drilling, and then using eyelets and a backing plate? I already have a roll bar so the car has plenty of holes in it, but it looks as if the tunnel side has fuel lines running where the eyelet would need to go.



Should I just sell it and get a harness that doesn't use eyelets / clips?



Thanks - here's some pics that may help also.
Attached Images
  
noid is offline   Reply With Quote
Old 12-01-2021, 11:14 PM   #2
RedReplicant
Senior Member
 
Join Date: Aug 2015
Drives: None
Location: Arizona
Posts: 960
Thanks: 1,533
Thanked 1,324 Times in 557 Posts
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Kinda confused what you're asking, but undo that bolt that you've got an arrow to and replace it with your eyelet.

For the sub belts you wrap them around the center section of the seat mount that has 4 bolts attached to it, assuming your harness doesn't have the clips sewn into it, otherwise you'd have to drill / backing plate for them.

Remember to cotter pin your harness clips too.
RedReplicant is offline   Reply With Quote
 
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
3D Printed Midbass Mounting Rings, OEM speaker harness pigtail projek_01 Audio/Visual, Electronics, Infotainment, NAV 3 08-07-2018 02:36 PM
aftermarket AGM battery mounting question CB390248 Engine, Exhaust, Transmission 0 01-23-2017 07:51 PM
Harness mounting in the rear with harness bar? HachiRo Cosmetic Modification (Interior/Exterior/Lighting) 4 06-29-2016 07:45 AM
Harness Mounting Points Shakkazombie Scion FR-S / Toyota 86 GT86 General Forum 0 04-15-2015 02:36 AM
4 Point harness mounting locations for stock seat raytrix DIY (Do-It-Yourself) Guides 29 04-11-2014 11:36 PM


All times are GMT -4. The time now is 09:23 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2025 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.