|
||||||
| Cosmetic Modification (Interior/Exterior/Lighting) Discussions about cosmetic mods. |
 |
|
|
Thread Tools | Search this Thread |
08-26-2014, 12:09 AM
|
#1 |
|
Senior Member
Join Date: Aug 2013
Drives: 14 Ultramarine FR-S
Location: SOCAL
Posts: 795
Thanks: 381
Thanked 415 Times in 232 Posts
Mentioned: 14 Post(s)
Tagged: 1 Thread(s)
|
Best Way to prep surface for spoiler
Can't seem to find too much on this topic.
For a spoiler that is gonna be put on with the 3m double sided tape. What is the best way to prep the area for the adhesive? I was going to wash the area with a mild dish soap, dry, claybar then rub the area with isopropyl alcohol. Are there any other preferred methods? I'm reinstalling my spoiler so I want to assure that it's not gonna lift, like it did the first time lol. Aside from cleaning the surface thoroughly I'll be using a heat gun to mold the spoiler to the trunk. Any other tips would be good, unsure if adhesive promoter is necessary or not or where to get it.
__________________
 2014 Ultramarine Scion FR-S 2000 Integra LS - SOLD  Last edited by Phantobe; 08-26-2014 at 12:21 AM. |
|
|
|
08-26-2014, 12:11 AM
|
#2 |
|
Senior Member
Join Date: May 2014
Drives: 2014 BRZ MT (Sold); 2006 V70R
Location: Fairfax
Posts: 873
Thanks: 10
Thanked 186 Times in 150 Posts
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
|
Make sure the surface is stripped of any residue or wax. Other than that, pressure and a bit of heat can help the tape stick better. I've never had an issue w/ doing it this way.
__________________
'14 BRZ LTD MT DGM
|
|
|
|
|
08-26-2014, 09:44 PM
|
#3 |
|
The Stig's African Cousin
Join Date: Apr 2014
Drives: 2014 wrb brz
Location: NJ
Posts: 720
Thanks: 1,547
Thanked 486 Times in 256 Posts
Mentioned: 4 Post(s)
Tagged: 1 Thread(s)
|
I did all that you mentioned I also made sure the trunk was hot I just left the car in the sun
|
|
|
|
|
08-26-2014, 10:10 PM
|
#4 |
|
Senior Member
Join Date: Jun 2013
Drives: RX-7 / BRZ
Location: USA
Posts: 2,349
Thanks: 1,031
Thanked 2,501 Times in 1,081 Posts
Mentioned: 27 Post(s)
Tagged: 0 Thread(s)
|
The adhesion promoter wipes they sell specifically for using 3m body molding tape... it is pretty much 90% isopropyl alcohol. After cleaning the area, removing wax run a cotton ball and the alcohol where the tape will be. Left it start to dry and then apply the tape/spoiler.
__________________
//2013 World Rally Blue BRZ Limited FBM Turbo--gone
//2018 Crystal White Pearl BRZ Ts 2.2l Harrop Supercharged |
|
|
|
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Yellow spots on surface of my car | tzhu07 | Scion FR-S / Toyota 86 GT86 General Forum | 21 | 08-25-2014 06:21 PM |
| Microsoft Surface | Gary in NJ | Electronics | Audio | NAV | Infotainment | 3 | 10-18-2013 11:57 AM |
| EDM armrest with a slight stain on the surface | Vten | Interior Parts (Incl. Lighting) | 5 | 10-13-2013 10:52 PM |
| Winter Car Prep | aghuman | Scion FR-S / Toyota 86 GT86 General Forum | 61 | 09-12-2013 07:12 PM |
| First Trackday Prep | solidONE | Tracking / Autocross / HPDE / Drifting | 40 | 03-23-2013 11:54 AM |
