Powder Coating Calipers Question - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Swolzee · 06-13-2021, 06:50 PM

I plan on doing the CTS-V big brake swap and have already sandblasted them down and have them ready for powder coat. However I'm running into an issue getting the piston boots out of the calipers.

I've watched several videos on disassembly of brembo calipers but none were the CTS-V ones. Which seem to have a metal retaining ring that holds in the boot that the other brembo variants do not have.

So my question in relation to powder coating is I was wondering if anyone has baked calipers with the boots in?

Directions call for a 15min bake at 400° F. Which means by the time the calipers got up to temp they'd only be that hot for about 10min or so and calipers reach in excess of 400° operating temps for longer durations during tracking and such.

So would the boots be fine to just leave in there?

Sapphireho · 06-13-2021, 07:50 PM

I might try to give Brembo a call.

Swolzee · 06-14-2021, 02:12 PM

Quote:

Originally Posted by Sapphireho

I might try to give Brembo a call.

I'm not sure how a call like that would work or what branch or location to contact.

NoHaveMSG · 06-14-2021, 03:52 PM

It would be easier to help if you posted a picture. Most of us are not going to even know how it looks. Have you tried browsing the CTS forums?

Sapphireho · 06-14-2021, 08:36 PM

Quote:

Originally Posted by Swolzee

I'm not sure how a call like that would work or what branch or location to contact.

You call, ask questions, they answer. Call the local branch, just like the girl scouts.

My god.

soundman98 · 06-14-2021, 10:25 PM

Quote:

Originally Posted by Swolzee

I'm not sure how a call like that would work or what branch or location to contact.

ask for el presidente regarding a very important question

Ultramaroon · 06-15-2021, 01:15 AM

Quote:

Originally Posted by Sapphireho

You call, ask questions, they answer. Call the local branch, just like the girl scouts.

My god.

Maybe you could just call for OP. You already know the important details.

Tcoat · 06-15-2021, 07:36 AM

Quote:

Originally Posted by Swolzee

I plan on doing the CTS-V big brake swap and have already sandblasted them down and have them ready for powder coat. However I'm running into an issue getting the piston boots out of the calipers.

I've watched several videos on disassembly of brembo calipers but none were the CTS-V ones. Which seem to have a metal retaining ring that holds in the boot that the other brembo variants do not have.

So my question in relation to powder coating is I was wondering if anyone has baked calipers with the boots in?

Directions call for a 15min bake at 400° F. Which means by the time the calipers got up to temp they'd only be that hot for about 10min or so and calipers reach in excess of 400° operating temps for longer durations during tracking and such.

So would the boots be fine to just leave in there?

The operating temperature for most calipers is around 350F anything above that you risk damage to the seals. You may get away with it if you leave the pistons in but otherwise the boots can warp.

Wally86 · 06-15-2021, 08:12 AM

From the horse's mouth

(855) 478-6565
Support – Brembo STORE USA
Call toll free at (855) 478-6565 to speak with Customer Service

Can't hurt to ask for the piece of mind.

Ultramaroon · 06-15-2021, 11:57 AM

Quote:

Originally Posted by Wally86

From the horse's mouth

(855) 478-6565
Support – Brembo STORE USA
Call toll free at (855) 478-6565 to speak with Customer Service

Can't hurt to ask for the piece of mind.

Swolzee · 06-16-2021, 10:10 AM

The third photo I couldn't get to focus but the blurry section is the metal ring.

I appreciate the help and the ball busting.

NoHaveMSG · 06-16-2021, 11:47 AM

Are you sure that is not part of the seal? All the rebuild kits I can find only include a dust seal and a piston seal.

Swolzee · 06-16-2021, 12:09 PM

Quote:

Originally Posted by NoHaveMSG

Are you sure that is not part of the seal? All the rebuild kits I can find only include a dust seal and a piston seal.

I'm not sure. What I do know is trying to use a pick and pull the boot from the surface edge you immediately are aware it's held firmly in and you hit an unyielding surface which is the ring.

I attempted to likewise extract the ring using a small flathead screwdriver to pry the ring up from the inside, however both efforts were futile or needed more force which would certainly tear the boot if applied.

Would you be so kind as to link those rebuild kits. I'd like to see the contents.

NoHaveMSG · 06-16-2021, 12:20 PM

Quote:

Originally Posted by Swolzee

I'm not sure. What I do know is trying to use a pick and pull the boot from the surface edge you immediately are aware it's held firmly in and you hit an unyielding surface which is the ring.

I attempted to likewise extract the ring using a small flathead screwdriver to pry the ring up from the inside, however both efforts were futile or needed more force which would certainly tear the boot if applied.

Would you be so kind as to link those rebuild kits. I'd like to see the contents.

Strange, I couldn't find any other reference to the retaining rings in any other forums.

https://racingbrake.com/search-results-page?q=bc-41

06-13-2021, 06:50 PM	#1
Swolzee Senior Member Join Date: Mar 2021 Drives: Honda Insight Location: North Carolina Posts: 113 Thanks: 39 Thanked 42 Times in 24 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	Powder Coating Calipers Question I plan on doing the CTS-V big brake swap and have already sandblasted them down and have them ready for powder coat. However I'm running into an issue getting the piston boots out of the calipers. I've watched several videos on disassembly of brembo calipers but none were the CTS-V ones. Which seem to have a metal retaining ring that holds in the boot that the other brembo variants do not have. So my question in relation to powder coating is I was wondering if anyone has baked calipers with the boots in? Directions call for a 15min bake at 400° F. Which means by the time the calipers got up to temp they'd only be that hot for about 10min or so and calipers reach in excess of 400° operating temps for longer durations during tracking and such. So would the boots be fine to just leave in there?

06-15-2021, 08:12 AM	#9
Wally86 Be Kind Join Date: Apr 2020 Drives: 2020 86 Location: MD Posts: 1,135 Thanks: 5,634 Thanked 1,328 Times in 641 Posts Mentioned: 7 Post(s) Tagged: 0 Thread(s)	From the horse's mouth (855) 478-6565 Support – Brembo STORE USA Call toll free at (855) 478-6565 to speak with Customer Service Can't hurt to ask for the piece of mind. __________________ [Insert clever signature here] IG \| WhiskyBlog \| Photography

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
powder coating?	all4spl	Mid-Atlantic	2	04-06-2017 11:36 AM
Powder Coating in NC?	ChilOut	Southeast	6	06-30-2014 06:04 PM
Powder coating on LI	klittl06	NY / NJ / CT / PA	7	06-09-2014 02:11 PM
Powder Coating	MATTrocity	Hawaii	3	05-07-2014 03:40 PM
So Cal powder coating	Plxdjake89	Southern California	4	09-02-2012 04:30 PM

06-13-2021, 07:50 PM	#2
Sapphireho Famous Potatoes Join Date: Mar 2016 Drives: '15 ultramarine Location: Idaho Posts: 14,049 Thanks: 5,816 Thanked 19,655 Times in 9,246 Posts Mentioned: 163 Post(s) Tagged: 0 Thread(s)	I might try to give Brembo a call.

06-16-2021, 10:10 AM	#11
Swolzee Senior Member Join Date: Mar 2021 Drives: Honda Insight Location: North Carolina Posts: 113 Thanks: 39 Thanked 42 Times in 24 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	The third photo I couldn't get to focus but the blurry section is the metal ring. I appreciate the help and the ball busting.

User Name		Remember Me?
Password