AIRAID FR-S / BRZ Cold Air Intake system Sneak Peak / Development Information - Page 28 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Pscylo · 08-21-2012, 11:03 PM

That's why I suggested the snorkel instead. looks like 2 - 10mm bolts hold it in place

MrBodyMassage · 08-22-2012, 12:02 AM

Quote:

Originally Posted by Subaruwrxfan

Interesting...could we run our intakes with the top lid off or would that be bad? lol

Hah! Great minds think alike! I was thinking of doing this too for more of an open element sound level. Can someone try this really fast and see if it effects sound?

Subaruwrxfan · 08-22-2012, 12:06 AM

Quote:

Originally Posted by MrBodyMassage

Hah! Great minds think alike! I was thinking of doing this too for more of an open element sound level. Can someone try this really fast and see if it effects sound?

Lol nice. I'm almost certain it will be louder, I just wanna make sure I won't be making it any less efficient or safe by removing the lid.

Pscylo · 08-22-2012, 12:06 AM

I'll do it tomorrow when I get off work.

Asphaltfrs1 · 08-22-2012, 12:45 AM

Quote:

Originally Posted by civicdrivr

I installed mine tonight since it came in a day early.

Initial impressions - its nice a throaty but not obnoxious at WOT, throttle response is slightly improved. I feel a bit more power in the midrange, but that could be in my head.

Im just annoyed that I lost one of the tiny screws and washers that hold the top plate on

Don't feel too bad, I dropped one of the 3 screws that hold the filter to the air box. The other two hold it pretty good, so I'm not stressing it

Plxdjake89 · 08-22-2012, 01:35 PM

Quote:

Originally Posted by Asphaltfrs1

Don't feel too bad, I dropped one of the 3 screws that hold the filter to the air box. The other two hold it pretty good, so I'm not stressing it

Lol I did the same s***! (but with the lid) and, I also dropped a washer out of the three I had left

AIRAID · 08-22-2012, 02:12 PM

Gentlemen –

We have been made aware of an issue that *Some* Intake tubes have too small of a hole for the supplied Barb fitting. Now this is clearly not all Intake tubes, as seen by all the great feedback and installed pictures on the forum. However if you are experiencing this issue with your Intake tube, please contact us direct for the resolution @ 1-800-498-6951.

I also wanted to address the situation where the MAF wiring harness is getting very close to the fan. I will have an updated set up instructions I will post that has the fix for that as well.

Remove the tape from the clip and move the clip 1.25” toward the firewall. The tape marks the original location of the clip.

Thanks,
David

zoomzoomers · 08-22-2012, 02:16 PM

Quote:

Originally Posted by Subaruwrxfan

I haven't gotten mine yet, but I dunno if I have the guts to rip back my bumper to remove the snorkel. If I want more sound I may just run it without the cover, I just don't wanna pull in hot engine air from the engine bay instead of inside of the bumper.

Removing the snorkel is a PITA!!! Especially, if you're doing the install alone like I did. Pulling the plastic bumper isn't the difficult part. It's the peeling it back, getting a small ratchet in the small confines, removing the bolts and removing the snorkel ALL ALONE is the PITA! I suggest that you have a buddy to help. It will make your life and the install go much smoother.

Jun_ · 08-22-2012, 03:05 PM

I have been lurking on this thread for a while now and read through everything. This intake looks fantastic and I can't wait till I get my BRZ. I will probably purchase this intake before I even get the car. Can't wait for my car to come. Another 2-3 months until the car reaches the dealership. D: I'm so impatient.

Subaruwrxfan · 08-22-2012, 04:11 PM

Quote:

Originally Posted by zoomzoomers

Removing the snorkel is a PITA!!! Especially, if you're doing the install alone like I did. Pulling the plastic bumper isn't the difficult part. It's the peeling it back, getting a small ratchet in the small confines, removing the bolts and removing the snorkel ALL ALONE is the PITA! I suggest that you have a buddy to help. It will make your life and the install go much smoother.

Yeah I'll be doing the install alone, so I think I'm gonna hold off on removing the snorkel for now.

AIRAID · 08-23-2012, 07:54 PM

FR-S | BRZ Sound Clips

[ame="http://www.youtube.com/watch?v=FIf-aSfHqlA&list=UUMePlwRkOXpOavVLgxPOZFA&index=1&feat ure=plcp"]AIRAID Intake For Scion FR-S | Subaru BRZ Sound Clips - YouTube[/ame]

industrial · 08-23-2012, 08:01 PM

Quote:

Originally Posted by Subaruwrxfan

Yeah I'll be doing the install alone, so I think I'm gonna hold off on removing the snorkel for now.

It wasn't that bad. There is a little groove in the bumper that hooks up with the top of the headlights, with just a little nudge you can pop it off and the front bumper becomes just flexible enough to get the snorkel out. I used to work on airplanes so I might be used to contorting my hands to get at bolts but it didn't seem that bad to me. I wouldn't do this on a cold day though!

tonystewart · 08-23-2012, 09:45 PM

Quote:

Originally Posted by David@Airaid

Remove the tape from the clip and move the clip 1.25” toward the firewall. The tape marks the original location of the clip.

I used a big ass zip tie, the thickness of the space was perfect for it and it's rated for 250 lbs on a powerpole and uv resistant.

AJUSA.com · 08-24-2012, 12:40 PM

Looks good! Thanks for the tip.

08-22-2012, 02:12 PM	#385
AIRAID Member Join Date: Jun 2012 Drives: FR-S Location: Phoenix, AZ Posts: 78 Thanks: 38 Thanked 109 Times in 50 Posts Mentioned: 7 Post(s)	*Gentlemen –* We have been made aware of an issue that *Some* Intake tubes have too small of a hole for the supplied Barb fitting. Now this is clearly not all Intake tubes, as seen by all the great feedback and installed pictures on the forum. However if you are experiencing this issue with your Intake tube, please contact us direct for the resolution @ 1-800-498-6951. I also wanted to address the situation where the MAF wiring harness is getting very close to the fan. I will have an updated set up instructions I will post that has the fix for that as well. Remove the tape from the clip and move the clip 1.25” toward the firewall. The tape marks the original location of the clip. Thanks, David Last edited by AIRAID; 08-22-2012 at 04:58 PM.

08-23-2012, 07:54 PM	#389
AIRAID Member Join Date: Jun 2012 Drives: FR-S Location: Phoenix, AZ Posts: 78 Thanks: 38 Thanked 109 Times in 50 Posts Mentioned: 7 Post(s)	FR-S \| BRZ Sound Clips [ame="http://www.youtube.com/watch?v=FIf-aSfHqlA&list=UUMePlwRkOXpOavVLgxPOZFA&index=1&feat ure=plcp"]AIRAID Intake For Scion FR-S \| Subaru BRZ Sound Clips - YouTube[/ame] Last edited by AIRAID; 08-24-2012 at 11:54 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Technical information on the Toyota D-4S system	arghx7	Engine, Exhaust, Transmission	72	01-13-2025 08:43 PM
cold air intake?	carbonBLUE	Engine, Exhaust, Transmission	72	09-30-2013 12:56 PM
FRS AEM Cold Air Intake	KenAEM	Engine, Exhaust, Transmission	28	10-24-2012 12:48 PM
2013 Scion FRS AEM Cold Air Intake	KenAEM	Engine, Exhaust, Bolt-Ons	2	07-12-2012 07:30 PM
Hello From AIRAID Filter Company	AIRAID	Announcements, Contests, Giveaways	3	06-11-2012 08:00 PM

08-22-2012, 03:05 PM	#387
Jun_ Member Join Date: Aug 2012 Drives: Satin White Pearl BRZ Limited Location: San Francisco Posts: 48 Thanks: 1 Thanked 3 Times in 3 Posts Mentioned: 2 Post(s)	I have been lurking on this thread for a while now and read through everything. This intake looks fantastic and I can't wait till I get my BRZ. I will probably purchase this intake before I even get the car. Can't wait for my car to come. Another 2-3 months until the car reaches the dealership. D: I'm so impatient.

08-24-2012, 12:40 PM	#392
AJUSA.com Senior Member Join Date: Jul 2012 Drives: BRZ Location: San Diego, CA Posts: 336 Thanks: 485 Thanked 151 Times in 85 Posts Mentioned: 7 Post(s)	Looks good! Thanks for the tip.

User Name		Remember Me?
Password