WHAT DID YOU DO TO YOUR BRZ TODAY? - Page 1418 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

dpfarr · 01-14-2024, 12:15 AM

Yea, the process for brembos is new to me. 30k miles and about 3mm of pad left. Very reasonable to be able to swap track pads in while switching wheels.

cmiovino · 01-17-2024, 08:41 PM

Quote:

Originally Posted by dpfarr

Yea, the process for brembos is new to me. 30k miles and about 3mm of pad left. Very reasonable to be able to swap track pads in while switching wheels.

It's quicker, but not exactly like "swap at a pitstop" quick.

Depending on thickness differences between the two sets of pads, you do have to move the pistons back in and the fronts take a decent amount of force. You can do it with a pad and wiggle it back and forth, but it takes some effort... especially going from a thin pad to a full one.

Pins take some effort in the front too. Best to pull them out from the rear rather than tapping from the front as you can scratch the caliper this way.

The rears being much smaller are simple all around.

... so when you think about traditional sliding calipers, there isn't a ton of advantages actually. It's just about the same effort removing one bolt, swinging the caliper away, swapping pads and/or moving only two pistons vs four, and you're good.

I've had both. They're not hard by any means, but not like half the time or anything.

NoHaveMSG · 01-18-2024, 10:34 PM

Quote:

Originally Posted by cmiovino

It's quicker, but not exactly like "swap at a pitstop" quick.

Depending on thickness differences between the two sets of pads, you do have to move the pistons back in and the fronts take a decent amount of force. You can do it with a pad and wiggle it back and forth, but it takes some effort... especially going from a thin pad to a full one.

Pins take some effort in the front too. Best to pull them out from the rear rather than tapping from the front as you can scratch the caliper this way.

The rears being much smaller are simple all around.

... so when you think about traditional sliding calipers, there isn't a ton of advantages actually. It's just about the same effort removing one bolt, swinging the caliper away, swapping pads and/or moving only two pistons vs four, and you're good.

I've had both. They're not hard by any means, but not like half the time or anything.

Need the right tools for the job. With a cheap or homemade pad spreading tool it takes minutes.

Ultramaroon · 01-18-2024, 10:48 PM

Quote:

Originally Posted by NoHaveMSG

Need the right tools for the job. With a cheap or homemade pad spreading tool it takes minutes.

If it needs to be faster than a c-clamp, I need to examine my priorities.

dpfarr · 01-20-2024, 01:02 AM

I had a Jetta that needed a tool that simultaneously spread and rotated the piston.

blsfrs · 01-20-2024, 09:57 AM

Quote:

Originally Posted by dpfarr

I had a Jetta that needed a tool that simultaneously spread and rotated the piston.

I had a Passat with the same type calipers. I spent an hour trying to push and screw the piston in (the video said it would be easy) then got the loaner tool and finished each one in 3 minutes.

NoHaveMSG · 01-20-2024, 05:44 PM

Quote:

Originally Posted by Ultramaroon

If it needs to be faster than a c-clamp, I need to examine my priorities.

My favorite tool for it is actually a clutch basket holder for a motorcycle.

Ultramaroon · 01-20-2024, 07:04 PM

Quote:

Originally Posted by NoHaveMSG

My favorite tool for it is actually a clutch basket holder for a motorcycle.

OMG, yes.

I've been doing it wrong all these years.

blsfrs · 01-21-2024, 10:16 AM

Quote:

Originally Posted by NoHaveMSG

My favorite tool for it is actually a clutch basket holder for a motorcycle.

Can you post a picture of the one you use. I googled around and saw some tools but I can't get my brain to see how they would work on brake calipers.

NoHaveMSG · 01-21-2024, 05:05 PM

Quote:

Originally Posted by blsfrs

Can you post a picture of the one you use. I googled around and saw some tools but I can't get my brain to see how they would work on brake calipers.

Like this. Tons of leverage, quick to adjust.

Kit Kat · 03-14-2024, 10:25 PM

Today, I installed my new head unit cover. The fitment was absolutely perfect

Name: Head Unit Cover.jpg
Views: 1003
Size: 402.8 KB

Name: 20240314_155259.jpg
Views: 890
Size: 434.9 KB

Oxyg3n · 03-16-2024, 01:59 AM

Got fresh fluids front to back

gen3v8 · 03-16-2024, 06:18 AM

Coolant, brake and clutch fluid?

Oxyg3n · 03-16-2024, 03:13 PM

I probably should be thinking about those next tbh. Brake fluid and spark plugs are next up on my list. Might pay someone to do those though since I'm getting old ��

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Saw My First FR-S Today	Marrk	Scion FR-S / Toyota 86 GT86 General Forum	26	05-15-2013 12:40 PM
Got my new FR-S today.	Boosted2.0	Scion FR-S / Toyota 86 GT86 General Forum	51	06-03-2012 10:35 PM
Sat in a FRS today!!	Ladnerd	Scion FR-S / Toyota 86 GT86 General Forum	12	04-30-2012 01:48 PM
Got my VIN today...	Enemies	BRZ First-Gen (2012+) — General Topics	63	04-12-2012 10:19 PM
sat in a BRZ today	NESW20	BRZ First-Gen (2012+) — General Topics	8	03-31-2012 08:53 AM

01-14-2024, 12:15 AM	#19839
dpfarr Senior Member Join Date: May 2020 Drives: BRZ ts Location: SACRAMENTO Posts: 767 Thanks: 424 Thanked 800 Times in 305 Posts Mentioned: 8 Post(s)	Yea, the process for brembos is new to me. 30k miles and about 3mm of pad left. Very reasonable to be able to swap track pads in while switching wheels.

01-20-2024, 01:02 AM	#19843
dpfarr Senior Member Join Date: May 2020 Drives: BRZ ts Location: SACRAMENTO Posts: 767 Thanks: 424 Thanked 800 Times in 305 Posts Mentioned: 8 Post(s)	I had a Jetta that needed a tool that simultaneously spread and rotated the piston.

03-14-2024, 10:25 PM	#19849
Kit Kat Junior Member Join Date: Jun 2017 Drives: 2017 Subaru BRZ w/ PP Location: Riverside, CA Posts: 1 Thanks: 0 Thanked 4 Times in 1 Post Mentioned: 0 Post(s)	Today, I installed my new head unit cover. The fitment was absolutely perfect

03-16-2024, 01:59 AM	#19850
Oxyg3n Senior Member Join Date: Oct 2015 Drives: 2017 BRZ - WRB Location: Bay Area Posts: 323 Thanks: 115 Thanked 209 Times in 109 Posts Mentioned: 2 Post(s)	Got fresh fluids front to back

03-16-2024, 06:18 AM	#19851
gen3v8 30 minute maintenance Join Date: Oct 2020 Drives: My18 wrxsti Location: Botany Bay Posts: 1,178 Thanks: 769 Thanked 1,236 Times in 631 Posts Mentioned: 7 Post(s)	Coolant, brake and clutch fluid?

03-16-2024, 03:13 PM	#19852
Oxyg3n Senior Member Join Date: Oct 2015 Drives: 2017 BRZ - WRB Location: Bay Area Posts: 323 Thanks: 115 Thanked 209 Times in 109 Posts Mentioned: 2 Post(s)	I probably should be thinking about those next tbh. Brake fluid and spark plugs are next up on my list. Might pay someone to do those though since I'm getting old ��

User Name		Remember Me?
Password