WHAT DID YOU DO TO YOUR BRZ TODAY?

[Wally86]

Originally Posted by Dirty Harry

OK. Has anyone on here had related problems with the twins though from dropping in a high flow filter? From what I’ve read K & N seem pretty reputable. But I guess there’s always a risk though, right?

https://www.ft86club.com/forums/showthread.php?t=56341


Should be fine but an interesting read none the less.

[Grady]

Originally Posted by The Red One

The key to lowering any perceived risk is:

• Don’t over oil after the cleaning. If it’s dripping you’re doing it wrong!

Exactly, oil will take out the MAF sensor. It will not destroy it but it will not work until you clean it correct.

[blsfrs]

Is there a trend towards dry filters again?


https://www.autoaccessoriesgarage.co...ne-Air-Filters

[Chuckls]

Originally Posted by Greenbottle

Did the door stay modification today. Quite easy to do thanks to advice on this forum.
Doors no longer auto close onto my legs.

Can you link this modification? Im quite tired of losing skin from my door closures.

[Qwimby1]

Originally Posted by Chuckls

Can you link this modification? Im quite tired of losing skin from my door closures.

Gotta do that. Its my biggest gripe about this car, Been putting it off because of that sticky stuff. were you able to do it by removing the speakers?

[Qwimby1]

Originally Posted by soundman98

but then on the flip-side, nohavemsg has some experience where the higher-flowing filters destroyed dirt bike motors because the filters didn't filter enough anymore

That's why I don't use them anymore. Too little gain for the potential risk.

[norcalpb]

Originally Posted by Wally86

Does this fix the squishy-ness of the stock dead pedal?

Somewhat, but it seems like there is styrofoam directly behind the carpet which I didn't remove.

[Dirty Harry]

Originally Posted by Wally86

https://www.ft86club.com/forums/showthread.php?t=56341


Should be fine but an interesting read none the less.

Good read, thanks for that. Maybe I’ll just add the Mishimoto silicon inlet tube, adds 3 whp and 2 tqs apparently with the stock filter, might be less risk and tidies the engine bay up a bit by getting rid of the sound tube, my main goal.

[Wally86]

Originally Posted by Dirty Harry

Good read, thanks for that. Maybe I’ll just add the Mishimoto silicon inlet tube, adds 3 whp and 2 tqs apparently with the stock filter, might be less risk and tidies the engine bay up a bit by getting rid of the sound tube, my main goal.

If you're looking for tidy, the sound tube delete is one part but I find myself bothered by the resonator tube that comes off of the side of the intake box. It seems to take up a lot of space for science I dont' understand And the TRD intake is just as wide as the stock box AND that resonator. Oh well.

[Wally86]

Originally Posted by Chuckls

Can you link this modification? Im quite tired of losing skin from my door closures.

https://www.ft86club.com/forums/show...=door+stay+mod

[CrowsFeast]

Originally Posted by Grady

Exactly, oil will take out the MAF sensor. It will not destroy it but it will not work until you clean it correct.

If there's enough oil on the filter to transfer to and impede the MAF's function then you put too much oil on the filter.

[Grady]

Originally Posted by CrowsFeast

If there's enough oil on the filter to transfer to and impede the MAF's function then you put too much oil on the filter.

That is what I was quoting. But thank you for having a stick and horse.

[Qwimby1]

Originally Posted by Greenbottle

Did the door stay modification today. Quite easy to do thanks to advice on this forum.
Doors no longer auto close onto my legs.

Then, again after advice here, I used a hand sucker to remove excess oil from the sump via the dipstick tube. Really didn't want to get ramps and stands for such a simple job. Removed half a litre and the oil level is now just over the top mark, hot or cold. Much happier with it now.

I thought I sent this earlier but don't see it anywhere. Were you able to do it by removing the speakers? Thus avoiding dealing with the awful sticky stuff on the plastic? That's all that's keeping me from doing it so far.

[Greenbottle]

Originally Posted by Qwimby1

I thought I sent this earlier but don't see it anywhere. Were you able to do it by removing the speakers? Thus avoiding dealing with the awful sticky stuff on the plastic? That's all that's keeping me from doing it so far.

Left the door panel hanging and just peeled the plastic back at the top corner so I could reach in to get the door stay. Used a hobby scalpel to slice the sealant a bit so the plastic didn't stretch or tear. Just pushed the plastic back onto the sealant before putting the door panel back on.