WHAT DID YOU DO TO YOUR BRZ TODAY? - Page 1385 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

RedReplicant · 12-27-2021, 10:51 PM

Quote:

Originally Posted by NoHaveMSG

2015 Subaru BRZ - ST/TT4 - Harrop, JRZ, OS Giken, etc

this, lol.

It is a Jack's Transmissions rebuild

NoHaveMSG · 12-28-2021, 11:26 AM

Quote:

Originally Posted by RedReplicant

this, lol.

It is a Jack's Transmissions rebuild

Jealous.

theraven762 · 12-28-2021, 02:51 PM

Got the Corsa installed today.
Still have to install my new header.

Jaden · 12-29-2021, 12:17 PM

Working on finishing up a twin supercharger build on my frs...

NoHaveMSG · 12-29-2021, 07:40 PM

Quote:

Originally Posted by Jaden

Working on finishing up a twin supercharger build on my frs...

That's, uh..............interesting

Jaden · 12-29-2021, 08:28 PM

Quote:

Originally Posted by NoHaveMSG

That's, uh..............interesting

Would you like to know more???

lol...

Jaden

Jaden · 12-30-2021, 11:22 AM

So originally I was going to use an m90 I had gotten off of a buick. The problem is it's difficult to intercool and I don't particularly like the idea of water meth injection. I'm on ethanol so I could've gotten away with it, until I had to use 91.

I wanted positive displacement and I was looking at ways to use fmic for air charge cooling.

Enter the amr500. Inexpensive, compact, can be mounted in any orientation and spin in any direction. Too small to be useful by itself, but two of them?

It gives 1000cc per revolution which is the same as the sprintex 210; however, they also have a higher maximum continuous rpm than the sprintex.

Two of these are pretty much perfectly sized for a stock block 86. You're looking at a Max of about 330 to 350 whp.

With the pulley setup I'm using, it will have about 275 to start off. I'll probably raise it up once I get larger injectors.

This morning I'm redoing the pulley setup to make them easily swappable.

I'll be doing a detailed build thread also.

Jaden

P.s. one of the best things about it is the known ccs per rev, which is identical to the sprintex 210. You can look at the compiled spreadsheet from that blower to accurately estimate what this one will do.

BrahmaBull1990 · 01-01-2022, 02:13 PM

After two weeks, I couldn’t stand not driving her due to being out of town and the weather. The roads are reasonably plowed and sanded up here in the PNW. Drove to Costco for ramen only to remember they are closed today.

Anyways, HAPPY NEW YEAR! May your mods be plentiful and your bearings un-spun.

grumpysnapper · 01-03-2022, 09:05 AM

Cut away enough of the "dribble" lip so that a sandwich plate can now sit where it is supposed to.... lower, more compact and making way more sense.
(no need for a riser plate and its extra seal)

demasrv · 01-04-2022, 09:06 PM

While I'm waiting for a buddy to get a night free to help me set the timing and put the timing cover back on, I took out the exhaust manifold studs, cleaned them up real nice and put them back in.

wolffbite · 01-05-2022, 04:02 PM

Played snowplow last week and the lip didn't survive a very snowy looking chunk of ice.

At least no bumper damage!

Grady · 01-05-2022, 07:00 PM

Quote:

Originally Posted by wolffbite

Played snowplow last week and the lip didn't survive a very snowy looking chunk of ice.

At least no bumper damage!

A bumper is less expensive than that STI lip.

wolffbite · 01-05-2022, 07:11 PM

Quote:

Originally Posted by Grady

A bumper is less expensive than that STI lip.

For the part yes, but not if including painting. Bodywork/paint is really damn expensive around here.

Ah well.. I'm replacing it with a much cheaper lip because I'm sure this won't be the last time this happens.

Grady · 01-05-2022, 09:37 PM

Quote:

Originally Posted by wolffbite

For the part yes, but not if including painting. Bodywork/paint is really damn expensive around here.

Ah well.. I'm replacing it with a much cheaper lip because I'm sure this won't be the last time this happens.

The first time I went off the track did the same and tore up my STI lip. I purchased a knock off and put the STI badge on it. It did not fit as well as the STI version but was only $100 instead of $500.

12-29-2021, 12:17 PM	#19380
Jaden Road-hole Join Date: Jul 2014 Drives: 2013 Whiteout FR-S Location: Gilbert, Arizona Posts: 1,112 Thanks: 272 Thanked 479 Times in 292 Posts Mentioned: 13 Post(s)	Wel... Working on finishing up a twin supercharger build on my frs... Attached Images

12-30-2021, 11:22 AM	#19383
Jaden Road-hole Join Date: Jul 2014 Drives: 2013 Whiteout FR-S Location: Gilbert, Arizona Posts: 1,112 Thanks: 272 Thanked 479 Times in 292 Posts Mentioned: 13 Post(s)	So originally I was going to use an m90 I had gotten off of a buick. The problem is it's difficult to intercool and I don't particularly like the idea of water meth injection. I'm on ethanol so I could've gotten away with it, until I had to use 91. I wanted positive displacement and I was looking at ways to use fmic for air charge cooling. Enter the amr500. Inexpensive, compact, can be mounted in any orientation and spin in any direction. Too small to be useful by itself, but two of them? It gives 1000cc per revolution which is the same as the sprintex 210; however, they also have a higher maximum continuous rpm than the sprintex. Two of these are pretty much perfectly sized for a stock block 86. You're looking at a Max of about 330 to 350 whp. With the pulley setup I'm using, it will have about 275 to start off. I'll probably raise it up once I get larger injectors. This morning I'm redoing the pulley setup to make them easily swappable. I'll be doing a detailed build thread also. Jaden P.s. one of the best things about it is the known ccs per rev, which is identical to the sprintex 210. You can look at the compiled spreadsheet from that blower to accurately estimate what this one will do. Last edited by Jaden; 12-30-2021 at 01:09 PM.

01-01-2022, 02:13 PM	#19384
BrahmaBull1990 Howdy Join Date: Feb 2021 Drives: 2020 BRZ PP Location: Snohomish, WA Posts: 589 Thanks: 1,271 Thanked 446 Times in 248 Posts Mentioned: 5 Post(s)	After two weeks, I couldn’t stand not driving her due to being out of town and the weather. The roads are reasonably plowed and sanded up here in the PNW. Drove to Costco for ramen only to remember they are closed today. Anyways, HAPPY NEW YEAR! May your mods be plentiful and your bearings un-spun. __________________ There's a point at 7,000 RPM... where everything fades. The machine becomes weightless. Just disappears. And all that's left is a body moving through space and time. 7,000 RPM. That's where you meet it. You feel it coming. It creeps up on you, close in your ear. Asks you a question. The only question that matters. Who are you? Last edited by BrahmaBull1990; 01-01-2022 at 05:03 PM.

01-03-2022, 09:05 AM	#19385
grumpysnapper Senior Member Join Date: Jan 2020 Drives: BRZ Location: Brisbane, Australia Posts: 352 Thanks: 309 Thanked 608 Times in 209 Posts Mentioned: 6 Post(s)	Cut away enough of the "dribble" lip so that a sandwich plate can now sit where it is supposed to.... lower, more compact and making way more sense. (no need for a riser plate and its extra seal) Attached Images

01-05-2022, 04:02 PM	#19387
wolffbite Just the tip Join Date: Mar 2017 Drives: 2017 DGM BRZ Location: BC, CANADA Posts: 633 Thanks: 921 Thanked 881 Times in 378 Posts Mentioned: 3 Post(s)	Played snowplow last week and the lip didn't survive a very snowy looking chunk of ice. At least no bumper damage! Attached Images

12-28-2021, 02:51 PM	#19379
theraven762 Junior Member Join Date: Dec 2021 Drives: 2018 Subaru BRZ tS Location: Raleigh, NC Posts: 9 Thanks: 0 Thanked 7 Times in 5 Posts Mentioned: 0 Post(s)	Got the Corsa installed today. Still have to install my new header.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Saw My First FR-S Today	Marrk	Scion FR-S / Toyota 86 GT86 General Forum	26	05-15-2013 12:40 PM
Got my new FR-S today.	Boosted2.0	Scion FR-S / Toyota 86 GT86 General Forum	51	06-03-2012 10:35 PM
Sat in a FRS today!!	Ladnerd	Scion FR-S / Toyota 86 GT86 General Forum	12	04-30-2012 01:48 PM
Got my VIN today...	Enemies	BRZ First-Gen (2012+) — General Topics	63	04-12-2012 10:19 PM
sat in a BRZ today	NESW20	BRZ First-Gen (2012+) — General Topics	8	03-31-2012 08:53 AM

User Name		Remember Me?
Password