killerb oil pickup - Page 2 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

ninjan00dles · 04-14-2021, 02:26 PM

Quote:

Originally Posted by TommyW

I used an IAG shortblock and my very competent engine builder used one so guessing there are no issues ay least with the FA20 version. I looked at it before install and it looked like a very solid unit compared to stock

Hey Tommy, do you have a baffled oil pan as well?

Joveen · 04-14-2021, 02:32 PM

I heard that it does pair up well with the maperformance pan/ full blown pan with baffle.

Sent from my SM-G998U using Tapatalk

Breadman · 04-14-2021, 02:39 PM

Quote:

Originally Posted by NoHaveMSG

Here is mine, too long, bottomed out on oil pan. After months of trying to get a replacement I told them to just forget it. I initially just asked for the measurement on how long it should have been and I was going to cut it myself. They insisted of me sending it in, I should have said forget it and just cut it the same length as the stock pickup. Basically paid 130 bucks to write a "do not recommend" review on their FB page.

i just measured mine with some calipers on a table and its 3.455" tall not sure what oem is. also i did get a bluemoon baffle because id like my engine to continue to get oil

NoHaveMSG · 04-14-2021, 02:55 PM

Quote:

Originally Posted by Breadman

i just measured mine with some calipers on a table and its 3.455" tall not sure what oem is. also i did get a bluemoon baffle because id like my engine to continue to get oil

I don't have a stock one to measure right now. I haven't tore apart my spare motor yet.

100% recommend the baffle.

Breadman · 04-14-2021, 03:09 PM

Quote:

Originally Posted by NoHaveMSG

I don't have a stock one to measure right now. I haven't tore apart my spare motor yet.

100% recommend the baffle.

the oem one i pulled out of my donor is 3.61" so slightly taller

TommyW · 04-14-2021, 04:42 PM

Quote:

Originally Posted by ninjan00dles

Hey Tommy, do you have a baffled oil pan as well?

No

Ultramaroon · 04-15-2021, 01:24 AM

Quote:

Originally Posted by NoHaveMSG

Most people I have heard got one had no issues. I don't think I would worry. I am not even that annoyed it was messed up, it was the whole ordeal of them getting me a replacement I just said forget it.

That's one epic QC fail. Thanks for calling them out on it.

Boccaccio · 04-15-2021, 05:30 AM

Quote:

Originally Posted by Ultramaroon

That's one epic QC fail. Thanks for calling them out on it.

I second this. Thank you!

For such a critical part, not to have strict 100% control via a measuring jig for example (which is based on the dimensions of the OE part - length, angle,...) is beyond me

This pick-up tube was also on my radar.

Perhaps I'll just make one myself...

Breadman · 04-15-2021, 08:26 AM

welp i had no idea this was an issue, i guess this is what hes talking about

Code Monkey · 04-15-2021, 11:53 AM

I have had mine for over 5,000 miles and multiple track days, no issues so far...

ninjan00dles · 05-01-2021, 05:59 PM

Just a datapoint. I just installed a KillerB pickup with a bluemoon baffle and everything fit fine. The pickup does come with a new set of socket head cap screws which I believe are too long though. It felt like they were bottoming out so I used the original OEM fasteners instead

jrhudson · 08-03-2021, 06:13 PM

Quote:

Originally Posted by ninjan00dles

Just a datapoint. I just installed a KillerB pickup with a bluemoon baffle and everything fit fine. The pickup does come with a new set of socket head cap screws which I believe are too long though. It felt like they were bottoming out so I used the original OEM fasteners instead

Can confirm bluemoon baffle and killer b oil pickup should work together with the oil pan. I mocked it up and its fine.

Also the provided allen bolts don’t bottom out. The bolt whole is about 19mm deep and the allen bolt is about 16mm. I even hand threaded the bolts in without any resistant.

NoHaveMSG · 08-03-2021, 08:12 PM

Quote:

Originally Posted by jrhudson

Can confirm bluemoon baffle and killer b oil pickup should work together with the oil pan. I mocked it up and its fine.

Also the provided allen bolts don’t bottom out. The bolt whole is about 19mm deep and the allen bolt is about 16mm. I even hand threaded the bolts in without any resistant.

Dry fit your oil pan over the top of it. That was my issue, pickup hit the oil pan.

jrhudson · 08-03-2021, 08:42 PM

Quote:

Originally Posted by NoHaveMSG

Dry fit your oil pan over the top of it. That was my issue, pickup hit the oil pan.

Yea thats what i did. It fits perfectly.

This is the end result. This pic is of when i applied the threebond on it. Sorry it isnt the best pic.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
OFT V1 Unmarried and KillerB Oil Pickup	Griever423	Engine, Exhaust, Bolt-Ons	7	04-09-2021 11:08 AM
Gap Between Oil Pickup & Oil Pan?	Bonburner	Engine, Exhaust, Transmission	2	10-17-2018 06:02 AM
FS: KillerB Delrin Shift Knob (Black)	skylinekin	Interior Parts (Incl. Lighting)	3	07-12-2017 08:09 PM
86 pickup	DavidBob	Scion FR-S / Toyota 86 GT86 General Forum	45	01-19-2015 02:10 AM
Wanted: BRZ in GTA with immediate pickup	smartAdmin	CANADA	0	07-10-2012 02:42 PM

04-14-2021, 02:32 PM	#16
Joveen Senior Member Join Date: Mar 2018 Drives: Bone stock Location: Windsor, CT Posts: 776 Thanks: 535 Thanked 234 Times in 164 Posts Mentioned: 8 Post(s) Tagged: 0 Thread(s)	I heard that it does pair up well with the maperformance pan/ full blown pan with baffle. Sent from my SM-G998U using Tapatalk

04-15-2021, 08:26 AM	#23
Breadman Senior Member Join Date: Jul 2017 Drives: 2017 BRZ w/PP Location: Pa Posts: 1,027 Thanks: 51 Thanked 302 Times in 225 Posts Mentioned: 3 Post(s) Tagged: 0 Thread(s)	welp i had no idea this was an issue, i guess this is what hes talking about

04-15-2021, 11:53 AM	#24
Code Monkey Senior Member Join Date: Jul 2016 Drives: Subaru BRZ Location: Atlanta, GA Posts: 869 Thanks: 972 Thanked 596 Times in 354 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	I have had mine for over 5,000 miles and multiple track days, no issues so far...

05-01-2021, 05:59 PM	#25
ninjan00dles Member Join Date: Oct 2020 Drives: 2015 FRS Location: Bay Area California Posts: 91 Thanks: 48 Thanked 67 Times in 35 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Just a datapoint. I just installed a KillerB pickup with a bluemoon baffle and everything fit fine. The pickup does come with a new set of socket head cap screws which I believe are too long though. It felt like they were bottoming out so I used the original OEM fasteners instead

User Name		Remember Me?
Password