Agency Power Exhaust Thread PT II - Page 9 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

ImAwesome · 07-26-2012, 05:01 PM

Thanks for doing this guys, Wish people would have been a little more patient with you

vividracing · 07-26-2012, 05:27 PM

Catback only runs was done. Car off dyno now mid pipe only.

TouchMyHonda · 07-26-2012, 05:30 PM

Really looking forward to the results.

Hawaiian · 07-26-2012, 05:42 PM

F5

SkullWorks · 07-26-2012, 06:07 PM

Quote:

Originally Posted by vividracing

--------------------------------------------
Pulley runs are now done. Stock pulley going back on.

Now on to each exhaust piece.

Ultimate transparency would mean posting these as they become available.....please

ichitaka05 · 07-26-2012, 06:15 PM

Quote:

Originally Posted by SkullWorks

Ultimate transparency would mean posting these as they become available.....please

Chill, let them get everything finish w. We don't need any mistakes cuz they were rushed to update.

Hawaiian · 07-26-2012, 06:33 PM

Quote:

Originally Posted by SkullWorks

Ultimate transparency would mean posting these as they become available.....please

The biggest concern was for a greater level of transparency. Posting dynos for each part with a new baseline for the lightened flywheel answers every question we have asked of vivid.

vividracing · 07-26-2012, 06:33 PM

Quote:

Originally Posted by SkullWorks

Ultimate transparency would mean posting these as they become available.....please

We have Video of each run. Photos of each part being installed. I am also taking photos of each part on the scale. Dyno runs are being done on the car as fast as we can get parts changed out.

The charts will be posted with all the info.

I am updating this thread as we go so you all can get a idea of the time it takes to pull all this off. This takes time. We don't have a TV film crew here. So we can not do all this in one hour.

Now the mid-pipe only runs are about to happen.

vividracing · 07-26-2012, 06:36 PM

Quote:

Originally Posted by Hawaiian

The biggest concern was for a greater level of transparency. Posting dynos for each part with a new baseline for the lightened flywheel answers every question we have asked of vivid.

I will try for today. But might be tomorrow get our car back on the dyno for two dyno runs.
One with everything stock but the flywheel/clutch
One with everything stock but the Flywheel/Clutch and Pulley.

This will give us an idea of how much the flywheel is doing. I think that is going to be pushed over to tomorrow as our current work is taking lots of time.

Hawaiian · 07-26-2012, 06:44 PM

Quote:

Originally Posted by vividracing

I will try for today. But might be tomorrow get our car back on the dyno for two dyno runs.
One with everything stock but the flywheel/clutch
One with everything stock but the Flywheel/Clutch and Pulley.

This will give us an idea of how much the flywheel is doing. I think that is going to be pushed over to tomorrow as our current work is taking lots of time.

Thank you, and good luck with the numbers.

vividracing · 07-26-2012, 06:45 PM

Quote:

Originally Posted by Hawaiian

Thank you, and good luck with the numbers.

Ha! No luck here. It is what it is.

denkigrve · 07-26-2012, 07:36 PM

Mike you guys are really going out of your way for this, and I feel like you guys deserve a thank you for doing that. Not many people would go this far to help people get over some e-drama from the past.

Lonewolf · 07-26-2012, 07:55 PM

Quote:

Originally Posted by SkullWorks

Ultimate transparency would mean posting these as they become available.....please

You heard master...u don wanna get whupped again do ya?

Edit: Skullworks takes grave offense to being jokingly labeled as a slavemaster for his immediate dyno demands...so don't take my post seriously guys.

vividracing · 07-26-2012, 08:41 PM

Just loaded up the car for the header only runs.

Next: header and cross-pipe only.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Agency Power Exhaust for the BRZ/FR-S at Redline360	Redline360	Engine, Exhaust, Bolt-Ons	5	07-24-2012 12:57 AM
Agency Power Exhaust	vividracing	Engine, Exhaust, Bolt-Ons	17	07-23-2012 03:40 PM
Agency Power Exhaust \| Best Price Anywhere	IslandImportPerformance	Engine, Exhaust, Bolt-Ons	13	07-21-2012 11:50 AM
Agency Power Exhaust in the works!	PrimeMotoring	Engine, Exhaust, Transmission	67	07-17-2012 07:57 AM

07-26-2012, 05:01 PM	#113
ImAwesome Senior Member Join Date: Jun 2012 Drives: 99' M3, 13' SWP Brz Location: Durham/Pinehurst, NC Posts: 346 Thanks: 89 Thanked 85 Times in 67 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	Thanks for doing this guys, Wish people would have been a little more patient with you

07-26-2012, 05:27 PM	#114
vividracing Join Date: May 2012 Drives: 2013 Scion FR-S Location: Gilbert, Arizona Posts: 2,593 Thanks: 491 Thanked 1,065 Times in 617 Posts Mentioned: 49 Post(s) Tagged: 3 Thread(s)	Catback only runs was done. Car off dyno now mid pipe only.

07-26-2012, 05:30 PM	#115
TouchMyHonda Vtec Jesus Join Date: Jul 2012 Drives: 13 BRZ, 13 Golf R, 15 Audi S4 Location: LSD Posts: 1,165 Thanks: 623 Thanked 243 Times in 153 Posts Mentioned: 5 Post(s) Tagged: 0 Thread(s)	Really looking forward to the results.

07-26-2012, 05:42 PM	#116
Hawaiian That guy Join Date: Feb 2012 Drives: Ultramarine mt FR-S Location: chicago Posts: 2,370 Thanks: 692 Thanked 1,389 Times in 730 Posts Mentioned: 71 Post(s) Tagged: 0 Thread(s)	F5

07-26-2012, 08:41 PM	#126
vividracing Join Date: May 2012 Drives: 2013 Scion FR-S Location: Gilbert, Arizona Posts: 2,593 Thanks: 491 Thanked 1,065 Times in 617 Posts Mentioned: 49 Post(s) Tagged: 3 Thread(s)	Just loaded up the car for the header only runs. Next: header and cross-pipe only.

User Name		Remember Me?
Password