WHAT DID YOU DO TO YOUR BRZ TODAY?

[Willpower]

Looks a lot like 50s era Seafoam Green. Gotta love it!

[norcalpb]

Originally Posted by JD001

What's the story behind the 'Tiffany Blue'? Nice powder coating.

I believe it’s a (actually trademarked) color by Tiffany & Co.

[therealstoly]

Originally Posted by JD001

What's the story behind the 'Tiffany Blue'? Nice powder coating.

Originally Posted by norcalpb

I believe it’s a (actually trademarked) color by Tiffany & Co.

True... It has been trademarked by Tiffany & Co. Copyright? Either way, they 'own' the colour. How it came to be an accent colour for me...

Rear STB reminded me of an old luggage handle and that thought just kinda stuck with me. Looked like you could open the trunk, reach in, and pick it up. The rubber mat had to go away for the STB and sub and I went to the fabric store to get something. I had no idea what but I didn't like any of the premade carpet options and I didn't want just the thin felt in the trunk. Saw this outdoor rated plaid fabric and that old luggage handle seedling of a thought came back and I decided to do a Burberry ish trunk. When it came time to put in the OEMAudio+ system the satin black sub looked wonky and so in keeping with the theme of the trunk, if you will, I decided a Tiffany Blue sub was the perfect accessory to accompany the Burberry trunk/luggage look. And so it began...

[Leonardo]

I love that color! One of my vehicles is accent in it.

[NoHaveMSG]

Originally Posted by spike021

Haven't driven it much yet with the gauge. Best I can say is the example in that screenshot, and then after driving home yesterday I parked with engine temp still at about 203 degrees F, and the pressure was down to maybe 3ish PSI.

Can update once I've driven at different speeds/temps.

Need to up that idle. 7psi is min hot idle, I think I have my car set to idle at 850 above 190 water temp, or something like that. I'd have to look at the table to tell you for sure. Could be your sending unit placement though.

[spike021]

Originally Posted by NoHaveMSG

Need to up that idle. 7psi is min hot idle, I think I have my car set to idle at 850 above 190 water temp, or something like that. I'd have to look at the table to tell you for sure. Could be your sending unit placement though.

It’s stock tune now though, so I can’t adjust the idle.

[NoHaveMSG]

Originally Posted by spike021

It’s stock tune now though, so I can’t adjust the idle.

It is probably alright, i'd just up it if you ever get a tune. Did you mount the sending unit under the AC compressor?

[spike021]

Originally Posted by NoHaveMSG

It is probably alright, i'd just up it if you ever get a tune. Did you mount the sending unit under the AC compressor?

Yeah, the top front oil galley plug spot.

[NoHaveMSG]

Originally Posted by spike021

Yeah, the top front oil galley plug spot.

The 7psi spec comes from the stock sending unit position. It may read higher there since I believe that is a dead end passage from the pump, that is where I run my sending unit for my gauge.

Correction: I was wrong, it does not dead end it feeds into the oil filter on that passage.

[spike021]

Originally Posted by NoHaveMSG

The 7psi spec comes from the stock sending unit position. It may read higher there since I believe that is a dead end passage from the pump, that is where I run my sending unit for my gauge.

Correction: I was wrong, it does not dead end it feeds into the oil filter on that passage.

Ahhh I see.

[HaXx]

I checked my brake pads, everything is A OK. tires looking good too

[JD001]

Originally Posted by HaXx

I checked my brake pads, everything is A OK. tires looking good too

I can't see your brake pads..

[dpfarr]

Originally Posted by JD001

I can't see your brake pads..

Took me a second too. Stuck against rotor.

[Ultramaroon]

Originally Posted by JD001

I can't see your brake pads..

Worst design ever