WHAT DID YOU DO TO YOUR FRS TODAY?

[jflogerzi]

Added a front splitter. I hope this bumper will hold. This splitter adds some weight

Sent from my GM1915 using Tapatalk

[Cedric]

Originally Posted by DarkPira7e

Where did you get that? I just made my own out of steel and some black fabric (steel so that it's magnetic for a phone or tablet mount). You can just barely see it, but I put a single DIN radio at the bottom

Toyota Part Number: 5552252020

It’s a radio cover for a Yaris. Fits perfect, but you need to glue it (or tape it) to the dash so it sits flush.


Sent from my iPhone using Tapatalk Pro

[Ashikabi]

Made a string rig so I can do my own alignments without tearing my hair out

Sent from my ONEPLUS A5010 using Tapatalk

[humfrz]

Originally Posted by Ashikabi

Made a string rig so I can do my own alignments without tearing my hair out

hmmmmm - looks like something that Bubba would rig up -

[Ashikabi]

Originally Posted by humfrz

hmmmmm - looks like something that Bubba would rig up -

If it works, it works

Sent from my ONEPLUS A5010 using Tapatalk

[Ohio Enthusiast]

Originally Posted by Ashikabi

Made a string rig so I can do my own alignments without tearing my hair out

Could you share some more details? Perhaps even a DIY thread? I've been doing my own string box alignments and would be very interested in this.

[humfrz]

Originally Posted by Ashikabi

If it works, it works

Sent from my ONEPLUS A5010 using Tapatalk

Well, Bubba does admit it looks pretty sophisticated, compared to his 7' piece of 1"x1" pine board with a nail in each end of it - plus a piece of chalk -

[humfrz]

Originally Posted by Ohio Enthusiast

Could you share some more details? Perhaps even a DIY thread? I've been doing my own string box alignments and would be very interested in this.

Don't ya'll have any alignment shops in the mid west? -

[Ashikabi]

Originally Posted by Ohio Enthusiast

Could you share some more details? Perhaps even a DIY thread? I've been doing my own string box alignments and would be very interested in this.

I used 8 90 degree elbows and 4 Ts. 2pieces of PVC pipe at 10ft each. Came up with about 3ft left over.

54 inch pipe between the Ts. Clamp the Ts to the spats/splitter to keep the rig from twisting. I'm not sure how to go about doing this with no splitter or spats/diffuser. You'd need a different way to mount it.

Anyways, I just kinda eyeballed the whole thing. Should be plenty good to hold a string in place. Now I can make an adjustment drop and roll the car to settle it and jack it up again without resetting the string box. I left the ends unglued from the central pipes so I could apply tension or disassemble for storage.

Total cost was about 40$ with all fittings, glue, and 4 clamps
@humfrz I've gotten approximately 6 alignments (attempts anyways). No one I've tried to work with has been willing, capable, or both, of working on it. Now that I have the swap and it sits higher I might have better luck but I'm tired of settling for a shit product when they can't figure out how to adjust aftermarket parts. Or how to set camber beyond zero



Sent from my ONEPLUS A5010 using Tapatalk

[humfrz]

Originally Posted by Ashikabi

Total cost was about 40$ with all fittings, glue, and 4 clamps
@humfrz I've gotten approximately 6 alignments (attempts anyways). No one I've tried to work with has been willing, capable, or both, of working on it. Now that I have the swap and it sits higher I might have better luck but I'm tired of settling for a shit product when they can't figure out how to adjust aftermarket parts. Or how to set camber beyond zero



Sent from my ONEPLUS A5010 using Tapatalk

Welp, Brian, down at the corner garage, may be a nice guy, but, you may consider taking your car to an alignment shop closer in to the city -

[Ashikabi]

Originally Posted by humfrz

Welp, Brian, down at the corner garage, may be a nice guy, but, you may consider taking your car to an alignment shop closer in to the city -

My problems have been in the city. Fucking plebs

Sent from my ONEPLUS A5010 using Tapatalk

[humfrz]

Originally Posted by Ashikabi

My problems have been in the city. Fucking plebs

Sent from my ONEPLUS A5010 using Tapatalk

Welp, maybe alignment machines just won't adjust that far out to give you what you want -

[Ashikabi]

Originally Posted by humfrz

Welp, maybe alignment machines just won't adjust that far out to give you what you want -

First problem is finding a rack that I can drive up on. Next is finding one that mounts the nodes on the wheels, not the tire (because tuck). Then, they still don't know what they are doing. I only had 4 degrees camber. No crazy stance

Sent from my ONEPLUS A5010 using Tapatalk

[RToyo86]

While leaving the cottage I heard a "tink" noise come from the left front, then I heard a metallic grinding noise. It sounded like a rock touching the rotor, and would come and go based on brake pressure, steering angle.

Drove it home, took it apart and found that the hardware clip on the caliper was damaged. The clip bent which was causing it to rub against the venting on the rotor. Luckily I had a spare clip on the shelf, so I swapped it out