WHAT DID YOU DO TO YOUR FRS TODAY?

[FRS13_]

So clean & shiny.

Sent from my SM-G892A using Tapatalk

[humfrz]

Originally Posted by FRS13_

So clean & shiny. Sent from my SM-G892A using Tapatalk

The red line tires are an interesting touch -


humfrz

[FRS13_]

Originally Posted by humfrz

The red line tires are an interesting touch -


humfrz

Thanks.

The red line is actually on the wheels.



Sent from my SM-G892A using Tapatalk

[mrderp]

Cleaned up my shed full of Nissan S14 parts. Threw away spare parts that were water damaged beyond repair.

Compared the OE exhaust from 2014 and the one from a canadian manual 2017.
Except for the flanges and tips being different everything else is exactly the same.

[humfrz]

Originally Posted by mrderp

Cleaned up my shed full of Nissan S14 parts. Threw away spare parts that were water damaged beyond repair.

Compared the OE exhaust from 2014 and the one from a canadian manual 2017.
Except for the flanges and tips being different everything else is exactly the same.

humfrz

[Tcoat]

Originally Posted by FRS13_

So clean & shiny.

Sent from my SM-G892A using Tapatalk

Looks like the original Hot Wheels cars!

[mrderp]

Originally Posted by humfrz

humfrz

Yeah I know, I wasn't clear in the post. the flanges are at the same location and are the same size but built differently. A picture is worth a thousand words

I recalled reading the 2017 had a revised design.
If that's the case, I guess my car didn't get the memo.

[itsAlex]

I did a bunch of stuff to my 86 this summer, but as far as exterior mods go, here's the following:

- Valenti Tail Lights Smoked
- Remark/GReddy Titanium Double Walled Tip Muffler Delete
- OEM rear diffuser

[SuperTom]

Originally Posted by itsAlex

I did a bunch of stuff to my 86 this summer, but as far as exterior mods go, here's the following:

- Valenti Tail Lights Smoked
- Remark/GReddy Titanium Double Walled Tip Muffler Delete
- OEM rear diffuser

Looks like Passenger side tip is hanging lower

[itsAlex]

Originally Posted by SuperTom

Looks like Passenger side tip is hanging lower

It is aha, I've tried adjusting the rubber things that hold the hangar hooks but it still stays slightly crooked, idk why... I believe the exhaust pipe may be bent?

[Axis2011KR]

Originally Posted by itsAlex

OEM rear diffuser

How much did this run you and do you have a part #? Dig the setup!

Just picked up my FR-S a few weeks back and thus far done:

FT-86 Speed Factory muffler delete
K&N Drop In Filter
Cut out the mesh in the Fog Light Bezels
Motul 600 Brake Fluid
Motul 300 Gear and Diff Fluid
Diode Dynamics 6000K HID/LED's in headlights, fogs, and DRL's
Diode Dynamics License Plate LED's
Diode Dynamics Interior Plate LED's
Drift Armor Front Bumper Beam ordered but not installed yet
Tein Flex Z Coilovers ordered but not installed yet

Last night installed my Perrin Brake Master Cylinder Brace. De-badging it over the weekend.

Next up is some Work CR2P 18x9.5 rims and some Dunlop Direzza ZIII 265-35-18's hopefully before year end

[humfrz]

Originally Posted by itsAlex

It is aha, I've tried adjusting the rubber things that hold the hangar hooks but it still stays slightly crooked, idk why... I believe the exhaust pipe may be bent?

Yep, Bubba suggests sticking a piece of pipe in the right exhaust, lift up while heating the last bend in the tail pipe with a torch.

Be advised, keep the pipe and torch handy - because it will always look crooked, depending upon what angle you look at it -


humfrz for Bubba

[itsAlex]

Originally Posted by Axis2011KR

How much did this run you and do you have a part #? Dig the setup!

Wow that's quite a list of things you've accomplished considering its only been a few weeks! And thanks! I should have worded my previous post differently as it's actually an "OEM-style diffuser" and not an actual OEM diffuser.

My diffuser is basically a replica of the OEM diffuser, minus the carbon-fiber pattern as I believe the actual OEM diffuser has a carbon fiber look to it. Here in Ontario I managed to pick it up at a local shop for ~$100.

[itsAlex]

Originally Posted by humfrz

Yep, Bubba suggests sticking a piece of pipe in the right exhaust, lift up while heating the last bend in the tail pipe with a torch.

Be advised, keep the pipe and torch handy - because it will always look crooked, depending upon what angle you look at it -


humfrz for Bubba

I might actually give this a try, I have one of those bernzomatic propane torch kits:



You think that should be sufficient?