NORCAL: Local Marketplace Buy/Sell

[Kaotic Lazagna]

Originally Posted by Bach415

You're such an enabler!

@Tofurky, which diffuser is it, aggressive or non-aggressive? More pics/condition?

[Bach415]

Originally Posted by Kaotic Lazagna

You're such an enabler!

@Tofurky, which diffuser is it, aggressive or non-aggressive? More pics/condition?

I don't enable, I encourage :X. Plus you wanted it for a while now I'm assuming. Both the splitter and diffuser is a great deal. Maybe he/she can take a bit off for picking up both at once?

[Kaotic Lazagna]

Originally Posted by Bach415

I don't enable, I encourage :X. Plus you wanted it for a while now I'm assuming. Both the splitter and diffuser is a great deal. Maybe he/she can take a bit off for picking up both at once?

lol, that's why it caught my eye. I was just looking at the installation manual for the rear diffuser, and it mentions a plastic rivet nut...I'm assuming that's permanently on the owner's car, so I'm not sure how I would install the diffuser on my car. =\

[Bach415]

Originally Posted by Kaotic Lazagna

lol, that's why it caught my eye. I was just looking at the installation manual for the rear diffuser, and it mentions a plastic rivet nut...I'm assuming that's permanently on the owner's car, so I'm not sure how I would install the diffuser on my car. =\

All those nuts and rivets and bolts are all purchasable through local hardware stores.

[Kaotic Lazagna]

Originally Posted by Bach415

All those nuts and rivets and bolts are all purchasable through local hardware stores.

I was hoping to not have to buy any hardware (I understand about the rivets tho), especially the spacers (I know hardware costs adds up quickly). And I wonder if the Berk muffler delete works with it as it's not listed on Velox's website.

[Bach415]

Originally Posted by Kaotic Lazagna

I was hoping to not have to buy any hardware (I understand about the rivets tho), especially the spacers (I know hardware costs adds up quickly). And I wonder if the Berk muffler delete works with it as it's not listed on Velox's website.

It should works since all it does is replace the axle back and not the whole catback. Hardware is decently priced. I had to replace all my bolts due to running it with a lip and buying a lot of spacers so :X.

[Kaotic Lazagna]

Originally Posted by Bach415

It should works since all it does is replace the axle back and not the whole catback. Hardware is decently priced. I had to replace all my bolts due to running it with a lip and buying a lot of spacers so :X.

I'll wait to hear back from seller on which version the diffuser is. When I replaced the hardware on a Tanabe strut bar I had on my previous car, I remember thinking it was expensive for what it was. Then again, only place I found them was at Ace Hardware.


Edit. It's the aggressive version. :sadbanana:

[Bach415]

Originally Posted by Kaotic Lazagna

I'll wait to hear back from seller on which version the diffuser is. When I replaced the hardware on a Tanabe strut bar I had on my previous car, I remember thinking it was expensive for what it was. Then again, only place I found them was at Ace Hardware.


Edit. It's the aggressive version. :sadbanana:

It's okay just sand down the strakes to make it look less aggressive lol. Then just get the splitter and save up for the diffuser? At most I think you'll be spending is 30 bucks for all the hardware (amazon-ing them) or a little more for in stores. Or maybe velox might be able to send them out to you for a small cost?

[Kaotic Lazagna]

Originally Posted by Bach415

It's okay just sand down the strakes to make it look less aggressive lol. Then just get the splitter and save up for the diffuser? At most I think you'll be spending is 30 bucks for all the hardware (amazon-ing them) or a little more for in stores. Or maybe velox might be able to send them out to you for a small cost?

I'd get it new at that point cuz it would look silly to have the endplates and no diffuser. Great deal tho for those who want the endplates.

[Bach415]

Originally Posted by Kaotic Lazagna

I'd get it new at that point cuz it would look silly to have the endplates and no diffuser. Great deal tho for those who want the endplates.

Up to you lol. I'd still get the splitter w/ the end plates. Not sure if you are confused about it but end plates are attached to the splitter and is in the front. It cost $200 for the end plates alone and with the splitter you're looking at about $600.

[Veloist]

FS: Michelin Pilot Super Sports 225/40/18 (set of 4)

Only has less than 500 miles on them. See Craigslist Post for more info https://sfbay.craigslist.org/pen/wto/6089604145.html

$520 or better offer, pretty motivated to sell.

Tires are on my car if you're interested I'll have Elite Performance unmount them.

[Kaotic Lazagna]

Originally Posted by Bach415

Up to you lol. I'd still get the splitter w/ the end plates. Not sure if you are confused about it but end plates are attached to the splitter and is in the front. It cost $200 for the end plates alone and with the splitter you're looking at about $600.

No no, I know they're at the ends of the splitter. Makes the front end look more aggressive. That's why with nothing in the rear, the aesthetic balance gets thrown off for me.

[einrejosh]

Originally Posted by einrejosh

Alright guys, I've got a couple of things for sale:

Stivo Rear Duckbill 37J (Looks like TRD rear trunk spoiler): $180

Radium Dual Catch Cans: $325


Grimmspeed Strut Bar (Black): $100


Openflash Header (1st Gen, gaskets not included): $400


(QTY: 4) 17x9.5 +38 5x100 RPF1's in Silver with 245/40-17 Michelin Pilot Super Sports
(3 Wheels have minor scratches on lip, Tires were bought in 2016, still at 7/32) : $1200


(QTY: 4) YokohamaYK 580's 245/40-17 (all-seasons) 7/32s on all 4: $400

Fortune Auto 500 (7k/8k spring rate, comes with new front end links): $1000

*will come in original packaging, as well as the certificate it came with and brand new never installed FA front endlinks

Stance Rear LCA V.1 : $380

*Comes with all hardware

*I am the first and only owner of these suspension components

Nameless muffled single exit axle-back : $140


Location:Union City; I can also meet up in: Hayward, Newark, and Fremont


Text only: (510)-Six73-4Eight73

Feel free to text or PM for questions or pics


Thanks Guys

Bump, edited 4/15



Sent from my iPhone using Tapatalk

[rraicu]

I am selling a shift knob that I tried on once but decided to go another way. Basically brand new.

-Raceseng Slammer - Shift Knob - Wrinkle Finish - Red - Toyota GT86 / Scion FR-S / Subaru BRZ | 2013+
-No Shift Gate Pattern Engraving
-1 x M12x1.25mm Adapter

Very easy to install. Weighs 635 grams (iirc) and it made my shifts smoother. Asking $100 obo. Can meetup in Palo Alto or nearby. Image attached is actual knob and adapter with original box. Please PM.