Full throttle Electric Supercharger Build Thread

[Sojhinn]

Originally Posted by vfrqqq

So my ESC is still not engaging when my PROcede controller is conneceted to the system. I went through and confirmed that I do have continuity on all of my connections on the PROcede wiring harness and tap points. I also confirmed that the PROcede controller has 12VDC on the red wire. After check all that, I also looked at whether the ESC controller is seeing voltage on the one signal wire from the PROcede controller. With the PROcede disconnected from the ESC controller (i.e., the WOT switch was connected up to the ESC controller so that the ESC didn't spool up--see below), I measured the voltage between the signal wire and ground while applying the throttle and with the engine running and observed no discernable change in voltage. So I’m guess that is probably why my ESC isn’t engaging with the PROcede installed; the ESC controller doesn't seem to be seeing any signal from the PROcede. I still haven’t confirmed whether my PROcede controller already has a throttle map loaded, but I’m hoping to solve my problems without having to lug my PC and monitor over to my garage. Beyond this, I’m not sure what I can do to troubleshoot my PROcede controller.







Incidentally, the ESC appears to spin up on its own when the ignition is in the ON mode and when the WOT switch or the PROcede controller is physically disconnected from the ESC controller—perhaps because there is no signal to the ESC controller? I'm not sure whether j_Zer0 and I are seeing the same situation, just different circumstances.

You need to set one of the parameters on the procede. It's multiple pages back. I'll try to find the picture I made.


Sent from my iPhone using Tapatalk

[Sojhinn]

Originally Posted by vfrqqq

So my ESC is still not engaging when my PROcede controller is conneceted to the system. I went through and confirmed that I do have continuity on all of my connections on the PROcede wiring harness and tap points. I also confirmed that the PROcede controller has 12VDC on the red wire. After check all that, I also looked at whether the ESC controller is seeing voltage on the one signal wire from the PROcede controller. With the PROcede disconnected from the ESC controller (i.e., the WOT switch was connected up to the ESC controller so that the ESC didn't spool up--see below), I measured the voltage between the signal wire and ground while applying the throttle and with the engine running and observed no discernable change in voltage. So I’m guess that is probably why my ESC isn’t engaging with the PROcede installed; the ESC controller doesn't seem to be seeing any signal from the PROcede. I still haven’t confirmed whether my PROcede controller already has a throttle map loaded, but I’m hoping to solve my problems without having to lug my PC and monitor over to my garage. Beyond this, I’m not sure what I can do to troubleshoot my PROcede controller.







Incidentally, the ESC appears to spin up on its own when the ignition is in the ON mode and when the WOT switch or the PROcede controller is physically disconnected from the ESC controller—perhaps because there is no signal to the ESC controller? I'm not sure whether j_Zer0 and I are seeing the same situation, just different circumstances.

Here you go:

https://drive.google.com/open?id=0B1...VlGOG5lV1dqWE0

https://drive.google.com/open?id=0B1...G5NRC10a2FoenM

Sojhinn


Sent from my iPhone using Tapatalk

[vfrqqq]

Originally Posted by Sojhinn

Here you go:

https://drive.google.com/open?id=0B1...VlGOG5lV1dqWE0

https://drive.google.com/open?id=0B1...G5NRC10a2FoenM

Sojhinn


Sent from my iPhone using Tapatalk

Awesome! I'll hook up the PROcede to my PC and see if that doesn't fix it.

[vfrqqq]

Originally Posted by vfrqqq

Awesome! I'll hook up the PROcede to my PC and see if that doesn't fix it.

Fixed!!

The PROcede controller is soooo much better than the WOT switch!

[Kpage]

Hey Guys, can we get an updated list? the last one I saw was in june-july. and I know that several have gone out and new users added.


Thanks!


KP

[Shiv@Openflash]

Originally Posted by vfrqqq

Fixed!!

The PROcede controller is soooo much better than the WOT switch!

Right on

[Yoda]

Originally Posted by Kpage

Hey Guys, can we get an updated list? the last one I saw was in june-july. and I know that several have gone out and new users added.


Thanks!


KP

This times 10

[Kpage]

I just want to go fast(er) than I do now...

[zc06_kisstherain]

Originally Posted by Yoda

This times 10

I probably will be next person to have ESC...

[Yoda]

Originally Posted by zc06_kisstherain

I probably will be next person to have ESC...

How are you so sure. Did they send you an email

[Kpage]

I thought I saw yours was on the way already. :-)

Sent from my SM-G900V using Tapatalk

[iJeff]

Originally Posted by Yoda

This times 10

Lists aren't published anymore but you can ask about your spot.

[zc06_kisstherain]

Originally Posted by Yoda

How are you so sure. Did they send you an email

go back and read posts in this thread

[rhythmM]

Originally Posted by zc06_kisstherain

go back and read posts in this thread

Hey, did you already receive your kit?