|
||||||
| Engine, Exhaust, Transmission Discuss the FR-S | 86 | BRZ engine, exhaust and drivetrain. |
 |
|
|
Thread Tools | Search this Thread |
09-03-2015, 08:17 PM
|
#1 |
|
Senior Member
Join Date: Aug 2015
Drives: 2015 WRB BRZ
Location: NorCal Bay Area
Posts: 284
Thanks: 133
Thanked 77 Times in 62 Posts
Mentioned: 4 Post(s)
Tagged: 2 Thread(s)
|
3" axleback to 2.5" mid pipe
Just picked up a Nameless 3" axleback. I ordered the right gasket from the Nameless website but it won't come in until next week. Can I reuse the stock gasket and hardware until then?
|
|
|
|
09-03-2015, 09:13 PM
|
#2 |
|
Senior Member
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 30,432
Thanks: 29,826
Thanked 32,845 Times in 16,844 Posts
Mentioned: 715 Post(s)
Tagged: 2 Thread(s)
|
You can use the same hangars.
The old gasket should fit; I don't recall a new gasket coming with mine. But, you might call Nameless just to make sure. 360-263-5001 humfrz |
|
|
|
|
09-04-2015, 12:05 AM
|
#3 | |
|
Senior Member
Join Date: Aug 2015
Drives: 2015 WRB BRZ
Location: NorCal Bay Area
Posts: 284
Thanks: 133
Thanked 77 Times in 62 Posts
Mentioned: 4 Post(s)
Tagged: 2 Thread(s)
|
Quote:
I guess I'll find out in the morning lol. . . |
|
|
|
|
|
09-04-2015, 12:18 AM
|
#4 | |
|
Senior Member
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 30,432
Thanks: 29,826
Thanked 32,845 Times in 16,844 Posts
Mentioned: 715 Post(s)
Tagged: 2 Thread(s)
|
Quote:
It would seem that either the 3" or the 2.5" would hook up the stock mid-pipe with the same gasket. However, best to check with Nameless, as I'm not sure how it is necked down. humfrz |
|
|
|
|
|
09-04-2015, 05:49 PM
|
#5 |
|
Senior Member
Join Date: Aug 2015
Drives: 2015 WRB BRZ
Location: NorCal Bay Area
Posts: 284
Thanks: 133
Thanked 77 Times in 62 Posts
Mentioned: 4 Post(s)
Tagged: 2 Thread(s)
|
Alright well, went ahead and tackled it this morning. Took about 10 mins total with an extra set of hands. The gasket didn't line up completely so I'll have to redo it when the gasket I ordered from Namelss comes in next week.
Told my buddy to rev it to 5k but it he took it to redline lol. . . there was a high pitch sound that came out, im assuming it was from the stock gasket not lining up. I didn't hear it while actually driving though. Completely satisfied with the sound  Video after install in my Instagram if interested: Ayoo_Adriannn Nameless 3"axle-back with 5" mufflers.  Compared to stock. Per website axle-back is ~17lbs while stock is ~25lbs 
Last edited by EzyBrzy; 09-04-2015 at 06:38 PM. |
|
|
|
|
09-04-2015, 09:46 PM
|
#6 | |
|
Senior Member
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 30,432
Thanks: 29,826
Thanked 32,845 Times in 16,844 Posts
Mentioned: 715 Post(s)
Tagged: 2 Thread(s)
|
Quote:
 humfrz |
|
|
|
|
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| WTT/WTS: Nameless 2.5", 5" Non-Offset Mufflers Axleback + Stock CBE for Perrin | kdbar | Engine, Exhaust, Bolt-Ons | 1 | 06-27-2015 02:04 PM |
| Quietest 2.5" axleback or midpipe+axleback for my JDL UEL? | stockysnail | Engine, Exhaust, Transmission | 22 | 03-28-2015 02:52 PM |
| FS: Subaru BRZ/Scion FR-S 2.5" Dual Exit Axleback Exhaust w/ 5" mufflers | LPC_FRS | Engine, Exhaust, Bolt-Ons | 7 | 08-25-2014 01:33 PM |
| REQ: Looking for sound clip of Nameless 2.5" "No Muffler" Dual Exhaust Axleback | jbsali | Engine, Exhaust, Transmission | 1 | 01-28-2014 08:22 AM |
| (SOLD) FS: (Ga) nameless 3" axleback 5" mufflers | mad_sb | Engine, Exhaust, Bolt-Ons | 5 | 08-29-2013 10:35 PM |
