Data Logs! Post them here.

[MGPAX]

What do you mean by LTFT's adapted? Is there somewhere I can look to see what range is good for each selected parameter?

Originally Posted by Wayno

Because you have too much information on the screen. Look at this instead.

http://datazap.me/u/mgpaxman/stg-1-d...zoom=6888-7193

It looks fine. Just log again once you have LTFT's adapted.

[MGPAX]

Stage 1 tune after 100 miles but with hot air temps:

http://datazap.me/u/mgpaxman/7-21?lo...zoom=3611-4190

[ztan]

Originally Posted by erok81

I have a few questions on these two logs.

This one is on spring pressure: http://datazap.me/u/erok81/log-1437240088?log=0&data=6

And this is high boost: http://datazap.me/u/erok81/log-1437240088?log=1&data=6

Both logs don't go to redline because I am seeing a few psi higher than my target levels. Due to that, I didn't want to rev it out too high just in case.

Looking at them I can see the IAM stays pretty constant at 0.7x. The AFR seems a little on the lean side too, but I'm not a tuner.

What do you guys think?

This is an off the shelf tune for a turbo car. My wastegate spring is 7.25psi and the high boost target should be 9psi. However, I usually see 9-10psi on the low map and 11-12psi on the high map.

What turbo and exhaust are you running, what fuel, and which off the shelf tune? Quite a bit of FLKC at WOT. I run quite a lot less cam overlap and a bit richer at WOT with minimal FLKC (Greddy T518Z). Your overboost may be wastegate size/flow related.

[Wayno]

Originally Posted by MGPAX

Stage 1 tune after 100 miles but with hot air temps:

http://datazap.me/u/mgpaxman/7-21?lo...zoom=3611-4190

Open up your tune in RR.
Open "Mass Airflow / Engine Load".
Open "MAF Sensor Scaling".
Change the value in the 3.44 g/rev column from 80.88 to 83.30.

That will make that lump between 4400 and 5500 more reasonable.

http://datazap.me/u/mgpaxman/7-21?lo...3855-3831-3801

[MGPAX]

@Wayno I can't open this tune as it is the one that came on my OFT. I have a greyed out export file icon when I see it in OFM.

I can't look at it at all in RR.
I can't look at the stock one either. EDIT: I finally figured out I can pull a .ori file onto RR. Still can't export OFT preloaded file tho. All good tho.

Help!! Please!

[itsjustdavep]

SO i installed my new Tomei UEL last night and flipped to the UEL e85 oft tune.

you guys seeing anything outta place? car feels and sounds fine

http://datazap.me/u/itsjustdavep/fir...=1-2-4-8-11-13

[phrosty]

Originally Posted by itsjustdavep

SO i installed my new Tomei UEL last night and flipped to the UEL e85 oft tune.

you guys seeing anything outta place? car feels and sounds fine

http://datazap.me/u/itsjustdavep/fir...=1-2-4-8-11-13

looks fine, though it's a very small log.

[itsjustdavep]

Originally Posted by phrosty

looks fine, though it's a very small log.

I'm about to go pull a full log here in a minute. Gotta drove bout a half hour

[Wayno]

Originally Posted by MGPAX

@Wayno I can't open this tune as it is the one that came on my OFT. I have a greyed out export file icon when I see it in OFM.

I can't look at it at all in RR.
I can't look at the stock one either. EDIT: I finally figured out I can pull a .ori file onto RR. Still can't export OFT preloaded file tho. All good tho.

Help!! Please!

Download from oft site.

[itsjustdavep]

Originally Posted by phrosty

looks fine, though it's a very small log.

what about these, i think i may have a small leak from header to OP, not sure if that'd reflect in the logs

http://datazap.me/u/itsjustdavep/len...g=0&data=12-13

http://datazap.me/u/itsjustdavep/len...og=1&data=1-13

[phrosty]

Originally Posted by itsjustdavep

what about these

You're consistently running slightly rich, even in closed loop. Not sure what to make of that.

[itsjustdavep]

Originally Posted by phrosty

You're consistently running slightly rich, even in closed loop. Not sure what to make of that.

I notice that now that I've been staring at em. I'm gonna slide a thicker gasket in between the header and the over pipe tomorrow. Maybe that leak is causing it

[MGPAX]

http://datazap.me/u/mgpaxman/runup-2...7-8&zoom=7-186

Mine are doing the same and I'm stage 1.
I need to scale my MAF sensor map.....but cant find a program that will work with the oft .csv files.

[MGPAX]

Originally Posted by Wayno

Download from oft site.

So the ones on the OFT are the same as the ones on the site?
Sorry...I didn't know...Just knew I couldn't look at it to see what it was.

Thanks for all your help btw~