Wheel Directory: Work Emotion XD9 18x9.0 +38 / 18x10.0 +18

[blags]

Ravspec - Do Work release 18x9+30 in 5x100 or are they a special order?

[dsgerbc]

Originally Posted by RavSpec

Should be no poke in the front with 8.5 +47.

If staying with 8.0, don't necessary need spacer. But if u want flush, I say around 15mm to 20mm spacers should do the trick.

Is all your info - with bare wheels or with tires mounted? My concern for 8" (and even for 7.5") +48 wheels is that even 225-wide rubber, tires could rub on the spring under load.

[FT86Katsu]

I wanna run 18x9s all around.. sounds like 18x9 +30 in the front with coils should be okay. Yeah?

[Jdogg180]

This may have been mentioned earlier but don't forget about the additional clearance you will have with a healthy dose of camber via your favorite adjustable suspension goodies. Another thought would be flaring that front fender out a bit to make something like an 18x9 +35 to 30 fit with a 245 or 255 tire. Its very likely with coilovers you will gain a good amount of clearance inboard. It seems to me like 18x9 +35 all around with a 255/35 tire would be achievable, with a little work of course, and probably be a very effective Non-Staggered track setup.

[denkigrve]

Hrm so I saw the post about 18x8.5 +47, but would +44 make much of a change? I should easily clear suspension since you're moving the wheel more outward bound correct?

I'm still super new to the wheel dynamics and math involved, but it sounds like you'd gain 3mm of inside clearance. Would they still fit in the fenders in the front? I'm thinking at 225 40 tire on that, but not sure if it would rub on the suspension under load.

[RavSpec]

Originally Posted by denkigrve

Hrm so I saw the post about 18x8.5 +47, but would +44 make much of a change? I should easily clear suspension since you're moving the wheel more outward bound correct?

I'm still super new to the wheel dynamics and math involved, but it sounds like you'd gain 3mm of inside clearance. Would they still fit in the fenders in the front? I'm thinking at 225 40 tire on that, but not sure if it would rub on the suspension under load.

Yup 18x8.5 +44 will sit better in the front.

[RavSpec]

Originally Posted by dsgerbc

Is all your info - with bare wheels or with tires mounted? My concern for 8" (and even for 7.5") +48 wheels is that even 225-wide rubber, tires could rub on the spring under load.

Nope, it's fine. Japan already tested 8.5 +47 with tires in the front.

Also 9.0 +38 with tires in the back will work as well.

[RavSpec]

Originally Posted by blags

Ravspec - Do Work release 18x9+30 in 5x100 or are they a special order?

Special order only

[blags]

All good, placed an order with you on nasioc

[CNC Autosports]

Here is a pic of our FR-S 18X8 et40 235/40R18 Dunlop. The front is perfect and the rear could use about a 10mm spacer. I have a set of Forgedstar F14 being made 19X8.5 et 45 and 19X9.5 et 42. Should be here in a few weeks

[denkigrve]

Originally Posted by CNC Autosports

Here is a pic of our FR-S 18X8 et40 235/40R18 Dunlop. The front is perfect and the rear could use about a 10mm spacer. I have a set of Forgedstar F14 being made 19X8.5 et 45 and 19X9.5 et 42. Should be here in a few weeks

What suspension is the car on? Is that still stock ride height?

[CNC Autosports]

Its 1.5 lower front and rear with a set of tein springs we had and modified.

[Staticfrost]

Originally Posted by CNC Autosports

Here is a pic of our FR-S 18X8 et40 235/40R18 Dunlop. The front is perfect and the rear could use about a 10mm spacer. I have a set of Forgedstar F14 being made 19X8.5 et 45 and 19X9.5 et 42. Should be here in a few weeks

Perfect cause the enkeis I was after is the same 18X8 et40. Now to start looking for some 10mm spacers for the rears.

[dnjshin0bi]

is it just me or does 18's look abit too big for a car this size? i mean this car is similar size to an s2k..