DIY - Oil pressure sender and gauge (Auberins) - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Trap63 · 02-14-2015, 11:39 AM

This is my job to install a smart gauge for oil pressure, very accurate and small. Wide alarm functions. Buzzer fitting too (opt).

Box it's a 1/32 DIN 22x45 mm and it fits very well inside "Push button start" box. You need to cut inner back . I mounted and fixed it with two plastic screws coming from two little clips (hot soldered).

About sender, you need unplug the cap near air intake throttle. You need a big torque as it is white loctite plugged.

Included wiring in combo is 3 ft (1 mt) and you need reach 2.50/2.60 mt . Max cable length admitted is 3 mt (9 ft)

From Auberins you need:
www.auberins.com/index.php?main_pag...products_id=226

http://www.auberins.com/index.php?ma...roducts_id=226

SYL1813 A (A is amber)
10 Bar (150 PSI) pressure sender P210
The combo includes sender, wiring and gauge, $89,95

To install the sender you need an adapter : M18x1,5 - 1/8 27 NPT

Some shoots

Inside the SYL1813A (make holes for air vent)

Follow included Auberins directions to setup (Bar or PSI) and for removing SYL1813 box for soldering it with plastic nuts.

Guillaume · 02-17-2015, 08:39 AM

Neat setup, I will follow that route if I decide to get an oil pressure gauge! Thanks for sharing.

Trap63 · 02-17-2015, 10:56 AM

Quote:

Originally Posted by Guillaume

Neat setup, I will follow that route if I decide to get an oil pressure gauge! Thanks for sharing.

In conjunction with Torque Pro on Android HU or HKS OB link you can see all parameters you need while racing. Auberins SYL1813 can send a signal to open or close adding fan for oilcooler, too. Very impressive and amazing for maintaining a stock look of internal design. I hate all "tuning" gauges....mostly in the wrong place.

Max FRS · 05-01-2015, 08:19 PM

Where did you get the adapters to install the sensor?

Max

Trap63 · 05-02-2015, 05:34 AM

Quote:

Originally Posted by Max FRS

Where did you get the adapters to install the sensor?

Max

I bought on Ebay, UK.

http://www.ebay.it/itm/LMA-Racing-Mo...item46195c308d

Max FRS · 05-02-2015, 09:06 PM

Thanks, just ordered one.

Max

FrX · 05-05-2015, 09:56 AM

You can get the adapter at FastWRX too: http://www.fastwrx.com/products/oil-gallery-plug

pleong · 08-03-2015, 12:44 PM

is there an alternative place to put the sensor? I was wanting to use this spot for an oil accumulator.

fatboydean · 08-19-2021, 06:23 PM

which LED color you chose? Red or Amber? I saw on the pic the 'red' box is checked...

Trap63 · 08-21-2021, 09:16 AM

Quote:

Originally Posted by fatboydean

which LED color you chose? Red or Amber? I saw on the pic the 'red' box is checked...

amber

fatboydean · 08-22-2021, 03:35 PM

thanks for the reply, I wonder how you deal with the wire lenth? just cut in the middle and add extension cords?

Trap63 · 08-22-2021, 03:39 PM

Quote:

Originally Posted by fatboydean

thanks for the reply, I wonder how you deal with the wire lenth? just cut in the middle and add extension cords?

you need an extension wire about 40 cm, no signal degradation is evaluable, respect wire section and solder it. Preferably to join not in engine bay.

fatboydean · 09-03-2021, 12:55 AM

one more question, you do need to have 12V supply for this unit in addition to the 3 sensor wires right?

Trap63 · 09-03-2021, 01:20 AM

Quote:

Originally Posted by fatboydean

one more question, you do need to have 12V supply for this unit in addition to the 3 sensor wires right?

yes, it is. ACC+ is the solution.

02-14-2015, 11:39 AM	#1
Trap63 Senior Member Join Date: Apr 2013 Drives: Brz WRB - Europe LHD Location: TURIN - Piedmont - ITALY Posts: 922 Thanks: 1,181 Thanked 841 Times in 289 Posts Mentioned: 40 Post(s)	DIY - Oil pressure sender and gauge (Auberins) This is my job to install a smart gauge for oil pressure, very accurate and small. Wide alarm functions. Buzzer fitting too (opt). Box it's a 1/32 DIN 22x45 mm and it fits very well inside "Push button start" box. You need to cut inner back . I mounted and fixed it with two plastic screws coming from two little clips (hot soldered). About sender, you need unplug the cap near air intake throttle. You need a big torque as it is white loctite plugged. Included wiring in combo is 3 ft (1 mt) and you need reach 2.50/2.60 mt . Max cable length admitted is 3 mt (9 ft) From Auberins you need: www.auberins.com/index.php?main_pag...products_id=226 http://www.auberins.com/index.php?ma...roducts_id=226 SYL1813 A (A is amber) 10 Bar (150 PSI) pressure sender P210 The combo includes sender, wiring and gauge, $89,95 To install the sender you need an adapter : M18x1,5 - 1/8 27 NPT Some shoots Inside the SYL1813A (make holes for air vent) Follow included Auberins directions to setup (Bar or PSI) and for removing SYL1813 box for soldering it with plastic nuts. __________________ Last edited by Trap63; 02-14-2015 at 12:03 PM.

02-17-2015, 08:39 AM	#2
Guillaume Senior Member Join Date: Jul 2012 Drives: Exige S 240 Location: Belgium Posts: 732 Thanks: 319 Thanked 602 Times in 287 Posts Mentioned: 4 Post(s)	Neat setup, I will follow that route if I decide to get an oil pressure gauge! Thanks for sharing. __________________ My car

08-03-2015, 12:44 PM	#8
pleong Senior Member Join Date: Nov 2012 Drives: 2013 Whiteout FR-S Location: Texas Posts: 815 Thanks: 163 Thanked 273 Times in 146 Posts Mentioned: 23 Post(s)	is there an alternative place to put the sensor? I was wanting to use this spot for an oil accumulator. __________________ TEAM NEMESIS \| NEM 86 \| IG: @NEM_86 PTE5858 Turbo \| Integrated Engineering Fuel Surge Tank \| 1300cc Injectors \| Exedy Twin Disc \| RAYS Volk ZE40 \| 295/30/18 \| 522whp @ 6,600 Dyno Dynamics The NEM86 Build Thread

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
oil pressure gauge	onemorelap	Engine, Exhaust, Transmission	69	03-04-2023 06:46 PM
Defi Oil Pressure Gauge and Cravenspeed Flexpod Gauge Mount Install and Review	Tye300	Cosmetic Modification (Interior/Exterior/Lighting)	10	05-22-2015 01:48 PM
Oil Pressure Observations - Anyone else using a gauge?	Dave-ROR	Engine, Exhaust, Transmission	29	01-20-2014 01:56 AM
Have a tire pressure gauge you really like?	Anthony	Tracking / Autocross / HPDE / Drifting	21	09-10-2013 07:09 PM
Oil Pressure Sender Unit Fitment Question	Captain Snooze	Engine, Exhaust, Transmission	2	07-06-2013 01:41 AM

05-01-2015, 08:19 PM	#4
Max FRS Member Join Date: Aug 2014 Drives: 2015 Halo FRS Automatic Location: Georgia Posts: 74 Thanks: 0 Thanked 22 Times in 16 Posts Mentioned: 1 Post(s)	Where did you get the adapters to install the sensor? Max

05-02-2015, 09:06 PM	#6
Max FRS Member Join Date: Aug 2014 Drives: 2015 Halo FRS Automatic Location: Georgia Posts: 74 Thanks: 0 Thanked 22 Times in 16 Posts Mentioned: 1 Post(s)	Thanks, just ordered one. Max

05-05-2015, 09:56 AM	#7
FrX Senior Member Join Date: May 2012 Drives: 2013 Scion FR-S, 1993 Lexus SC300 Location: Houston, TX Posts: 411 Thanks: 284 Thanked 175 Times in 102 Posts Mentioned: 5 Post(s)	You can get the adapter at FastWRX too: http://www.fastwrx.com/products/oil-gallery-plug

08-19-2021, 06:23 PM	#9
fatboydean Member Join Date: Apr 2020 Drives: 2016 BRZ Hikari Location: British Columbia Posts: 78 Thanks: 30 Thanked 16 Times in 14 Posts Mentioned: 1 Post(s)	which LED color you chose? Red or Amber? I saw on the pic the 'red' box is checked...

08-22-2021, 03:35 PM	#11
fatboydean Member Join Date: Apr 2020 Drives: 2016 BRZ Hikari Location: British Columbia Posts: 78 Thanks: 30 Thanked 16 Times in 14 Posts Mentioned: 1 Post(s)	thanks for the reply, I wonder how you deal with the wire lenth? just cut in the middle and add extension cords?

09-03-2021, 12:55 AM	#13
fatboydean Member Join Date: Apr 2020 Drives: 2016 BRZ Hikari Location: British Columbia Posts: 78 Thanks: 30 Thanked 16 Times in 14 Posts Mentioned: 1 Post(s)	one more question, you do need to have 12V supply for this unit in addition to the 3 sensor wires right?

User Name		Remember Me?
Password