PTUNING 4-1 Full T304 SS Equal Length Double-Slip Race Header (200+whp 93 pump gas)

[jflogerzi]

Originally Posted by D.Scrye

Very interested in OFT tune: subscribed. Also, how loud do you reckon these would be with a resonated midpipe with a 200 cell cat? Particularly during the winter...

Define loud as this very subjective....

[D.Scrye]

Something like a rough db or percentile guesstimate vs totally stock and/or completely catless (with muffler).

[FRSGeek]

Just for reference sake: My PBlks, HKS Catted Headers, Motive OP, Invida (2.3"0D) FP and TRD 2" section/2.25" sections cat-back and Drift-Office tune.

Made: 188.19 HP 4th gear pull on ~93 Oct. as I had a splash of race fuel in there. Oh and the place was 76-80f in the bay.

Now is has: PBlks, HKS Catted Headers, Motive OP, Berk? 2.5" catted FP and Perrin 2.5" cat back. No dyno.

Originally Posted by jflogerzi

I would be intrested in seeing your tune and header with the Crawford power blocks.

[phobos512]

Originally Posted by D.Scrye

Something like a rough db or percentile guesstimate vs totally stock and/or completely catless (with muffler).

There are way too many factors...The overpipe (material? schedule (thickness)? diameter?), front pipe (material? schedule (thickness)? catted? resonated? diameter?), midpipe (material? schedule (thickness)? resonated? muffled? diameter?), axle-back (material? schedule (thickness)? resonated? muffled? diameter? number of tips? length of pipes to the tips?)...

There'd be no way for them to make a statement and have it mean anything unless it was on an otherwise completely stock vehicle with a particular number of miles on it (given the tendency for muffling material to move over time).

[Snowball]

*Fingers crossed*...shipping today...shipping today...shipping today...lol


Sent from my iPhone using Tapatalk

[Andrew025]

Originally Posted by Snowball

*Fingers crossed*...shipping today...shipping today...shipping today...lol


Sent from my iPhone using Tapatalk

Probably going to be at least a couple more weeks I'm guessing.
Hope I'm wrong though

[Mrc@ptuning]

Originally Posted by Andrew025

Probably going to be at least a couple more weeks I'm guessing.
Hope I'm wrong though

We're getting a handful of the headers in mid/late next week and the remainder the following week. We will be shipping out the header as soon as they are received. All orders will be shipped out no later than the 22nd of October. Our fabricators have been working through the past few weekends to complete all the production headers--it's a very complex race header to produce. Again, we apologize for the delay and thank you for your patience. It will be worth the wait, once you see the production header.


On a side note, we are currently working on an optional OEM-style heat shield for our race header. This heat shield will address any concerns about under hood temps.


MrC

[Snowball]

Awesome news guys any idea how much the heat shield will be? Also, when it might get released? I might hold off on installing if the heat shield is released closely afterwards.


Sent from my iPhone using Tapatalk

[Andrew025]

Originally Posted by Mrc@ptuning

We're getting a handful of the headers in mid/late next week and the remainder the following week. We will be shipping out the header as soon as they are received. All orders will be shipped out no later than the 22nd of October. Our fabricators have been working through the past few weekends to complete all the production headers--it's a very complex race header to produce. Again, we apologize for the delay and thank you for your patience. It will be worth the wait, once you see the production header.


On a side note, we are currently working on an optional OEM-style heat shield for our race header. This heat shield will address any concerns about under hood temps.


MrC

Thanks for the update.
Any update on the OFT possibility?

[chaoskaze]

Was already interested, and might cone with OFT tune?! Subed!

[Thunderleg]

Looks good! subscribed for more

[solidONE]

Have they shipped out? Can't wait to see some dynos with 91 octane and E85.

[ecko04]

Originally Posted by solidONE

Have they shipped out? Can't wait to see some dynos with 91 octane and E85.

Exactly 5 posts above yours

Originally Posted by Mrc@ptuning

We're getting a handful of the headers in mid/late next week and the remainder the following week. We will be shipping out the header as soon as they are received. All orders will be shipped out no later than the 22nd of October. Our fabricators have been working through the past few weekends to complete all the production headers--it's a very complex race header to produce. Again, we apologize for the delay and thank you for your patience. It will be worth the wait, once you see the production header.


On a side note, we are currently working on an optional OEM-style heat shield for our race header. This heat shield will address any concerns about under hood temps.


MrC

[ecko04]

Originally Posted by bjun

Sorry guys quick question, I've been busy lately so I haven't had time to catch up on things.
So I got my oil cooler few days ago, has the headers been shipped out too?

Post from a couple days ago

Originally Posted by Mrc@ptuning

We're getting a handful of the headers in mid/late next week and the remainder the following week. We will be shipping out the header as soon as they are received. All orders will be shipped out no later than the 22nd of October. Our fabricators have been working through the past few weekends to complete all the production headers--it's a very complex race header to produce. Again, we apologize for the delay and thank you for your patience. It will be worth the wait, once you see the production header.


On a side note, we are currently working on an optional OEM-style heat shield for our race header. This heat shield will address any concerns about under hood temps.


MrC