OpenFlash Tablet: RomRaider parameters for Launch Control and Flat-foot Shift

[Danklvr]

LC / FFS not avail on the Bo1C rom yet. Shiv said it will be avail on the new set of OTS maps, once he releases them.

[KslayFRZ]

Any update?

Sent from my SPH-L900 using Tapatalk

[steve99]

Originally Posted by KslayFRZ

Any update?

Sent from my SPH-L900 using Tapatalk

pretty sure ls ffs enabled now in v1.5 and v2 tunes for b01c and dooc tunes open in romraider with oft definitions and see if tables exist

[KslayFRZ]

The table exist in rr....

Took it up to 4500 and it didn't kick in. Didn't want to wake the neighbors lol but is it set higher?

Sent from my SPH-L900 using Tapatalk

[lucid215]

Originally Posted by KslayFRZ

The table exist in rr....

Took it up to 4500 and it didn't kick in. Didn't want to wake the neighbors lol but is it set higher?

Sent from my SPH-L900 using Tapatalk

if you didnt change it its set to 5500 rpms

[KslayFRZ]

Not to sound lazy but can someone walk me through this...

I know how to open the map in rr
My rr won't checksum
The table with lc/ff has 3 other sub charts
None of them say 5500

Sent from my SPH-L900 using Tapatalk

[steve99]

Originally Posted by KslayFRZ

Not to sound lazy but can someone walk me through this...

I know how to open the map in rr
My rr won't checksum
The table with lc/ff has 3 other sub charts
None of them say 5500

Sent from my SPH-L900 using Tapatalk

read the OFT TIPS thread below its all in there

better still read all the links

ignore the checksum error message when you save rom it will be corrected and oft corrects the checksum anyway.

[lucid215]

it starts off at 7500 so whatever you want you it set at just minus that from 7500. automatically its set to 5500 so the box will say 2000. i have mine set to 4k so my box reads 3500.

[KslayFRZ]

Thank you so much @Lucid25 @Steve 99 for the help and guidance. It was successful lol

Now....


Is there a link to walk you through dialing in your mods?

Ie perrin inlet tube abd drop in
x should be set to this
Y should be set to this
?

Sent from my SPH-L900 using Tapatalk

[Turdinator]

Originally Posted by KslayFRZ

Thank you so much @Lucid25 @Steve 99 for the help and guidance. It was successful lol

Now....


Is there a link to walk you through dialing in your mods?

Ie perrin inlet tube abd drop in
x should be set to this
Y should be set to this
?

Sent from my SPH-L900 using Tapatalk

Take some logs and see how it looks. If you have LTFT over about 3% then scaling your MAF is a good place to start. There is a great thread on it and a link to it in steve99's signature.

[el-92]

So is this still not available for the 2014 boc1?? I don't see the launch control table anywhere .a quick yes or no because I can't seem to find it . thank you

[steve99]

Originally Posted by el-92

So is this still not available for the 2014 boc1?? I don't see the launch control table anywhere .a quick yes or no because I can't seem to find it . thank you

your on a V2 oft tune and using the definitions supplied with those tunes ?

I just opened a B01C rom using correct defs and the lc/ffc parameters are their at the bottom of the list

your probably using the old V1.5 defs

read this post by shiv re using the correct definitions

http://www.ft86club.com/forums/showthread.php?t=70796

[el-92]

Originally Posted by steve99

your on a V2 oft tune and using the definitions supplied with those tunes ?

I just opened a B01C rom using correct defs and the lc/ffc parameters are their at the bottom of the list

your probably using the old V1.5 defs

read this post by shiv re using the correct definitions

http://www.ft86club.com/forums/showthread.php?t=70796

So I'll look into this when I'm off work thanks for the reply steve99 but should the oft already come with the v2 tune since I just bought less then a week ago ?

[steve99]

Originally Posted by el-92

So I'll look into this when I'm off work thanks for the reply steve99 but should the oft already come with the v2 tune since I just bought less then a week ago ?

most likely it was preloaded with v2 tunes however to edit you will need to download v2 tunes and romraider defs from oft site.