Kraftwerks Supercharger Owners Thread

[post_break]

Talked to Bill, he's hooking me up. Zach@DeliciousTuning ignore my PM.

[zoth]

@KraftWerks Mike from Moto-East will be calling to send me the MAP sensor that is missing. Looks like your packing dept. still never got this right yet.

[DeliciousTuning]

Originally Posted by post_break

Talked to Bill, he's hooking me up. Zach@DeliciousTuning ignore my PM.

Hey,

I wasn't ignoring your pm's. During the day I actually have an entirely separate full time job. I try to balance the two and respond to everyone's messages from 7am-4pm pst, but I can't always respond right away. Rest assured I would have gotten back to you after I got off my day job had you waited

Sincerely,

Zach
Delicious Tuning

[post_break]

Originally Posted by sales@delicioustuning.com

Hey,

I wasn't ignoring your pm's. During the day I actually have an entirely separate full time job. I try to balance the two and respond to everyone's messages from 7am-4pm pst, but I can't always respond right away. Rest assured I would have gotten back to you after I got off my day job had you waited

Sincerely,

Zach
Delicious Tuning

I wasn't saying you were ignoring me. I was saying to ignore me cause I called bill lol. Everything is cool sorry for the confusion.

Sent from my SGH-M919 using Tapatalk

[ZionsWrath]

Anyone running a full 2.5 exhaust and header? Sound clips?

[Proof]

Is there a thread I should post questions in? I see this is an "Owners" thread.

Either way. I see there is a base tune that can be purchased with the package. But in the future would a set of tunes be available for for 93 and E85 map switching? I do not care about flex fuel so would rather have two tunes.

Thank you for your time gang. I am very excited about this product.

[glamcem]

Originally Posted by ZionsWrath

Anyone running a full 2.5 exhaust and header? Sound clips?

I have full 2.5" exhaust but with OEM headers since headers don't add much with FI and some cause fitment issues..I will post some video when I get a chance

[SPCorBUST]

Anybody have a C38 and get tuned? Would like to use it as a base, and happy to give a kickback for it

[Kakawate]

Originally Posted by ZionsWrath

Anyone running a full 2.5 exhaust and header? Sound clips?

I have buddy club header with no cat, invidia over pipe, invidia resonated front pipe, m7 non resonated cat back.

Honestly I think this video is when I still had the factory front cat and over pipe
[ame]http://youtu.be/xo8irObJUy4[/ame]

My build

http://www.ft86club.com/forums/showthread.php?p=1340047

[Freeman]

Originally Posted by ZionsWrath

Anyone running a full 2.5 exhaust and header? Sound clips?

No 2.5 inch but I do have a 3 inch header back setup.

Perrin 3 inch resonated cat back
Nameless 3 inch resonated OP/DP with Helmholtz resonator
Borla UEL (JDL UEL has been ordered to replace the Borla)

I can snag some sound clips once the install is finished.

[post_break]

Missing parts from my kit so far. About 40% into the install. The M10 25MM that goes on the top bracket holding the supercharger plate on. Going to Home Depot tomorrow morning to purchase one. Hopefully nothing else is missing ugh.

[zoth]

@KraftWerks aren't these idler pulley's supposed to be toothed if they need to be can you send them together with the my map sensor that is also missing. It's really frustrating that your in the middle of the build and darn parts are missing.

Good quality products, but oh boy your packing dept. really need to ease up on the drinks.

Now I'm stuck with a limp tune because I'm using the OEM map sensor.

Can we arrange a faster shipping. This baby is my DD

[zoth]

Originally Posted by post_break

Missing parts from my kit so far. About 40% into the install. The M10 25MM that goes on the top bracket holding the supercharger plate on. Going to Home Depot tomorrow morning to purchase one. Hopefully nothing else is missing ugh.

I fell your pain man...

I'm freaking stuck...

[SPCorBUST]

I may have gotten the wrong molded coupler when I left the facility today. At least, I actually hope that thats the case.

The one I have is smaller on one side and larger on the other. The larger side slides right over the hot side pipe perfectly, but the smaller side will not fit over the outlet of the supercharger.

My thoughts are that this means it was truly meant for the C30, since the larger side can slide over the supercharger outlet perfectly. After checking, it seems like it's because the supercharger outlet and the intercooler pipe inlets are almost the same size. (all of the pipe inlets and outlets are this size)

Tagging @KraftWerks for a reply here... Hope to get this resolved

Met some of the folks there and they were pleasant to deal with.