xDJ DUBx's Asphalt Rocket Bunny Monogram Series FRS Build - Page 8 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

xDJ DUBx · 04-18-2014, 04:22 PM

Quote:

Originally Posted by Diode Dynamics

Did you get it on yet!

The anticipation is killing us

Nick C.

Not just yet haha, I'll post pics soon

Diode Dynamics · 04-18-2014, 04:43 PM

Quote:

Originally Posted by xDJ DUBx

Not just yet haha, I'll post pics soon

Good....good...good. lol

Nick C.

meeskee2 · 04-18-2014, 04:59 PM

Quote:

Originally Posted by xDJ DUBx

Wrenching away

TEASE!

StancedLifestyle · 04-20-2014, 06:06 AM

LOL Greg! I hate you soo much! :P Give me your parts!

xDJ DUBx · 04-21-2014, 03:39 PM

So I installed the LCAs and KWs, but my toe is out bad now. Any suggestions? Not sure what I did wrong. The LCA's didn't come with much help and I couldn't find much on the forums.

xDJ DUBx · 04-22-2014, 05:48 PM

Figured out I need some adjustable toe rods to go with the LCAs so I put the stock ones back in for now. Enough teases..

Rocket bunny on stock wheels makes baby jesus cry

So we first tried to install the rivet nuts on the driver rear using a bolt and nut but that was way too inconsistent so we decided not to however the big rivet nut holes were already drilled. So we mounted the other 3 corners with the small self tapping screws the kit comes with until I could find the unicorn rivet nut tool to properly install the rivet nuts however we couldn't mount the driver rear at all since it was already drilled out too big for the screws. The car was also too low in the rear and I was having a horrible time driving due to out bad the toe was but it was late and I had to get home.

The next day I luckily found the rivet nut tool I needed to properly install the rivet nuts so last night I raised the rear of the car, reinstalled the stock LCA's and installed the rivet nuts on the driver rear then mounted the final flare so it is now complete.

I am going to get an alignment today just to get everything back in line since the height is alright now. Then this weekend I am going to pull all the self tapping screws out and replace them with the rivet nuts. I hope that my rear wheels will be ready for pick up this Saturday and if so, I will be installing/fitting them as well and adjusting the height accordingly then getting another alignment if need be. That'll pretty much be it until I get the front wheels by the end of next month. Then I'll install/fit those properly and readjust the height one last time then another alignment to get it exactly where I want it. It is THEN after this that I will pull the kit off and get it painted.

TL;DR: It's getting there, just give me some time. Cheers.

xDJ DUBx · 04-22-2014, 05:55 PM

Oh yeah and I will closing up the rear quarters on Saturday then getting them welded shut on sunday.

Fett4Real · 04-22-2014, 06:05 PM

Very good progress

FR-FKN S! · 04-28-2014, 01:02 AM

is that the greddy rocket bunny kit ?? looks really good cant wait 2 c the wheels !!

akahenry · 04-28-2014, 01:22 AM

sex

Simon99 · 04-28-2014, 01:26 AM

Quote:

Originally Posted by FR-FKN S!

is that the greddy rocket bunny kit ?? looks really good cant wait 2 c the wheels !!

Pretty sure the title says Rocket Bunny monogram

Sent from my SGH-I337M using Tapatalk

FR-FKN S! · 04-28-2014, 04:00 AM

Quote:

Originally Posted by Simon99

Pretty sure the title says Rocket Bunny monogram

Sent from my SGH-I337M using Tapatalk

yes there are a lot of replica rocket bunny kits plus i was asking him thanks 4 the input tho

xDJ DUBx · 04-28-2014, 05:26 PM

Quote:

Originally Posted by FR-FKN S!

yes there are a lot of replica rocket bunny kits plus i was asking him thanks 4 the input tho

Yes it's a genuine Trakyoto 6666 Rocket Bunny kit distributed by Greddy USA. No replica parts on this build.

sirsol66 · 04-28-2014, 11:28 PM

Can you post photos of what you end of doing with the quarter panels? That's been my biggest question with the rocket bunny builds. Car looks great!

04-20-2014, 06:06 AM	#102
StancedLifestyle Member Join Date: Sep 2013 Drives: 2014 Asphalt FR-S Location: Temple City/ Riverside Posts: 76 Thanks: 0 Thanked 4 Times in 4 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	LOL Greg! I hate you soo much! :P Give me your parts! __________________ 2012 Honda Fit Sport 5 spd M/T PMM (Sold) http://farm8.staticflickr.com/7330/9...05979d9c_o.jpg 2014 Scion FRS 6 spd M/T Asphalt (Current) Stanced Lifestyle https://www.facebook.com/stancedcreation

04-21-2014, 03:39 PM	#103
xDJ DUBx Lurker Join Date: Jul 2013 Drives: '14 Rocket Bunny Monogram FRS Location: High Desert, CA Posts: 274 Thanks: 64 Thanked 152 Times in 95 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	So I installed the LCAs and KWs, but my toe is out bad now. Any suggestions? Not sure what I did wrong. The LCA's didn't come with much help and I couldn't find much on the forums. __________________ Rocket Bunny Monogram Series

04-22-2014, 05:48 PM	#104
xDJ DUBx Lurker Join Date: Jul 2013 Drives: '14 Rocket Bunny Monogram FRS Location: High Desert, CA Posts: 274 Thanks: 64 Thanked 152 Times in 95 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Figured out I need some adjustable toe rods to go with the LCAs so I put the stock ones back in for now. Enough teases.. Rocket bunny on stock wheels makes baby jesus cry So we first tried to install the rivet nuts on the driver rear using a bolt and nut but that was way too inconsistent so we decided not to however the big rivet nut holes were already drilled. So we mounted the other 3 corners with the small self tapping screws the kit comes with until I could find the unicorn rivet nut tool to properly install the rivet nuts however we couldn't mount the driver rear at all since it was already drilled out too big for the screws. The car was also too low in the rear and I was having a horrible time driving due to out bad the toe was but it was late and I had to get home. The next day I luckily found the rivet nut tool I needed to properly install the rivet nuts so last night I raised the rear of the car, reinstalled the stock LCA's and installed the rivet nuts on the driver rear then mounted the final flare so it is now complete. I am going to get an alignment today just to get everything back in line since the height is alright now. Then this weekend I am going to pull all the self tapping screws out and replace them with the rivet nuts. I hope that my rear wheels will be ready for pick up this Saturday and if so, I will be installing/fitting them as well and adjusting the height accordingly then getting another alignment if need be. That'll pretty much be it until I get the front wheels by the end of next month. Then I'll install/fit those properly and readjust the height one last time then another alignment to get it exactly where I want it. It is THEN after this that I will pull the kit off and get it painted. TL;DR: It's getting there, just give me some time. Cheers. __________________ Rocket Bunny Monogram Series

04-22-2014, 05:55 PM	#105
xDJ DUBx Lurker Join Date: Jul 2013 Drives: '14 Rocket Bunny Monogram FRS Location: High Desert, CA Posts: 274 Thanks: 64 Thanked 152 Times in 95 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Oh yeah and I will closing up the rear quarters on Saturday then getting them welded shut on sunday. __________________ Rocket Bunny Monogram Series

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Goomba's Rocket bunny FRS build	Goomba_james	Member's Car Journals	106	06-22-2014 12:02 PM
Supercharged Rocket Bunny Widebody Conversion Build Thread	RWDRIFT	Member's Car Journals	278	01-06-2014 01:12 AM
Taylor's Asphalt Rocket Bunny	Taylorsmith-	Member's Car Journals	46	11-20-2013 04:27 AM
EPIC Frs Rocket Bunny Build!!	pitstops	Member's Car Journals	37	08-21-2013 11:46 AM
2JZ Rocket Bunny Drift 86 build (Dubai)	ultra	FR-S & 86 Photos, Videos, Wallpapers, Gallery Forum	43	11-15-2012 05:17 PM

04-22-2014, 06:05 PM	#106
Fett4Real AKA Mugen Dom Join Date: May 2013 Drives: 2013 FR-S, 2007 FJ Voodoo Blue Location: Hill AFB UT Posts: 957 Thanks: 125 Thanked 337 Times in 239 Posts Mentioned: 8 Post(s) Tagged: 0 Thread(s)	Very good progress

04-28-2014, 01:02 AM	#107
FR-FKN S! Senior Member Join Date: Sep 2013 Drives: Raven FRS Location: Honolulu, Hawaii Posts: 101 Thanks: 8 Thanked 33 Times in 22 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	is that the greddy rocket bunny kit ?? looks really good cant wait 2 c the wheels !!

04-28-2014, 01:22 AM	#108
akahenry Senior Member Join Date: Jul 2013 Drives: '18 STi Location: Bay Area Posts: 837 Thanks: 1,315 Thanked 201 Times in 155 Posts Mentioned: 5 Post(s) Tagged: 0 Thread(s)	sex

04-28-2014, 11:28 PM	#112
sirsol66 Senior Member Join Date: Apr 2013 Drives: 2013 FRS- Hot Lava Location: Michigan Posts: 674 Thanks: 16 Thanked 162 Times in 115 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	Can you post photos of what you end of doing with the quarter panels? That's been my biggest question with the rocket bunny builds. Car looks great!

User Name		Remember Me?
Password