Third Party Testing: Crawford Billet Power Blocks (BPB / Manifold Spacers) - Page 13 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

nelsmar · 04-01-2014, 01:39 PM

Quote:

Originally Posted by OrbitalEllipses

FYI, I did say if these made power as claimed I'd ask for a ban.

@Hachiroku, 30 day temp-ban pls.

True man right here.

Crawford Performance · 04-01-2014, 01:41 PM

Quote:

Originally Posted by xxscaxx

Any chance you guys could make a one off spacer that is a lot smaller? I wanted to do spacers for my innovate supercharger but have minimal clearance. Just figured i'd ask. @Crawford Performance

You know, that's a good idea. If a smaller Block is needed for the SC market then we would be glad to make them for ya.

Just get us a height and we will make it so.

xxscaxx · 04-01-2014, 01:43 PM

Quote:

Originally Posted by Crawford Performance

You know, that's a good idea. If a smaller Block is needed for the SC market then we would be glad to make them for ya.

Just get us a height and we will make it so.

It has to be pretty thin - how thin do you think you could make it without it being counterproductive? I had a conversation with someone at Innovate so I will go back and look at the clearance. Lucky for me I have stiffer engine mounts so I may be able to get away with a mm or so higher, but they will need to be small.

s2d4 · 04-01-2014, 01:43 PM

Quote:

Originally Posted by xxscaxx

Any chance you guys could make a one off spacer that is a lot smaller? I wanted to do spacers for my innovate supercharger but have minimal clearance. Just figured i'd ask. @Crawford Performance

Wouldn't it look more awesome with the charger poking through the hood?

TouchMyHonda · 04-01-2014, 01:45 PM

Quote:

Originally Posted by Crawford Performance

You know, that's a good idea. If a smaller Block is needed for the SC market then we would be glad to make them for ya.

Just get us a height and we will make it so.

xxscaxx · 04-01-2014, 01:46 PM

Quote:

Originally Posted by s2d4

Wouldn't it look more awesome with the charger poking through the hood?

I will have to try to figure out the clearance. Not only that, Innovate users would need a slightly longer belt depending on the spacer height.

Crawford Performance · 04-01-2014, 01:47 PM

Quote:

Originally Posted by xxscaxx

It has to be pretty thin - how thin do you think you could make it without it being counterproductive? I had a conversation with someone at Innovate so I will go back and look at the clearance. Lucky for me I have stiffer engine mounts so I may be able to get away with a mm or so higher, but they will need to be small.

We can ask Sean for a dimension or someone with one of the setups can come by the shop and we can measure for ourselves.

xxscaxx · 04-01-2014, 01:52 PM

Quote:

Originally Posted by Crawford Performance

We can ask Sean for a dimension or someone with one of the setups can come by the shop and we can measure for ourselves.

If I wasn't in NY i'd gladly come by

If you need me to I will reach out. Just keep me posted.

xjohnx · 04-01-2014, 01:54 PM

Quote:

Originally Posted by xxscaxx

It has to be pretty thin - how thin do you think you could make it without it being counterproductive? I had a conversation with someone at Innovate so I will go back and look at the clearance. Lucky for me I have stiffer engine mounts so I may be able to get away with a mm or so higher, but they will need to be small.

I can't imagine they'd be able to make them large enough to make a difference and still fit with the innovate.

[ame="https://www.youtube.com/watch?v=Xlq3XspyBH0"]Innovate Motorsports: FR-S Non-Intercooled 75mm Pulley - Under hood road test - YouTube[/ame]

xxscaxx · 04-01-2014, 01:58 PM

Quote:

Originally Posted by xjohnx

I can't imagine they'd be able to make them large enough to make a difference and still fit with the innovate.

Good post with the video - I was looking for that.

But those are on stock motor mounts. Also, would possibly require trimming the stock hood a little, but I can't tell how much clearance is between there so I will wait until further testing is done lol

Crawford Performance · 04-01-2014, 01:58 PM

Quote:

Originally Posted by xjohnx

I can't imagine they'd be able to make them large enough to make a difference and still fit with the innovate.

Oh, there is not much room for sure. The only way to know for sure would be to make a set then ask our Dyno its opinion

xxscaxx · 04-01-2014, 02:09 PM

Could always try using a different material if the Billet is too small and doesn't do its job correctly regarding heat - but not sure if thats an option.

DriftHappens · 04-01-2014, 02:56 PM

OH GOD THAT WHINE! i love it.

Lonewolf · 04-01-2014, 03:31 PM

Quote:

Originally Posted by Crawford Performance

Oh, there is not much room for sure. The only way to know for sure would be to make a set then ask our Dyno its opinion

Or make a hood with a power dome/bulge...any fabricators interested?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Crawford Billet Power Blocks	smbstyle	Engine, Exhaust, Transmission	799	01-18-2016 06:01 PM
Crawford Performance Turbo BRZ! Balance Meets Power - Ignition Episode 71	ZetaVI	BRZ Photos, Videos, Wallpapers, Gallery Forum	22	04-01-2014 06:19 PM
Squidbelly wants to know the best way to gut a manifold cat	regal	Engine, Exhaust, Transmission	14	03-07-2014 11:31 AM
short blocks?	350matt	Engine, Exhaust, Transmission	4	11-04-2013 09:37 PM
Billet Oil Catch Can #BC-175 by Billet Custom	Tim_Asphalt_FRS	Engine, Exhaust, Transmission	48	10-27-2013 03:29 PM

04-01-2014, 02:09 PM	#180
xxscaxx Senior Member Join Date: Jul 2012 Drives: 2013 SWP BRZ Location: New York Posts: 2,240 Thanks: 458 Thanked 878 Times in 556 Posts Mentioned: 34 Post(s) Tagged: 0 Thread(s)	Could always try using a different material if the Billet is too small and doesn't do its job correctly regarding heat - but not sure if thats an option.

04-01-2014, 02:56 PM	#181
DriftHappens Member Join Date: Nov 2013 Drives: '14 FRS White Location: Las Vegas Posts: 77 Thanks: 22 Thanked 44 Times in 31 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	OH GOD THAT WHINE! i love it.

User Name		Remember Me?
Password