Wheel Directory: Enkei RPF1 17x9.0 +35 - Page 26 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

JS + BRZ · 03-10-2014, 06:09 PM

Woot woot.

JS + BRZ · 03-11-2014, 01:44 AM

So if I get two camber bolts, can I add in some negative camber? I have 245 40 rs3 on my +35 rpf1s.

Thank you!

Sent from my SCH-I605

Squishy86 · 03-11-2014, 06:22 AM

Camber bolts will give you about a degree to a degree and a half. I did that and almost maxed out my camber plates for 2.5 degrees.

Sent from my SAMSUNG-SGH-I337 using Tapatalk

JS + BRZ · 03-11-2014, 01:14 PM

Is there a difference in camber I can get with 14mm and 16mm bolt?

Squishy86 · 03-11-2014, 02:24 PM

Quote:

Originally Posted by JS + BRZ

Is there a difference in camber I can get with 14mm and 16mm bolt?

Have looked at your struts before? You know the part where the two bolts that connect the knuckle to the strut? The bottom bolt is 14mm and the top bolt is 16mm. When you install your "camber bolt" its the same thing as the bottom 14mm bolt but now you place it through the top. So now you have 14mm bolts on both the top and bottom. The difference is while the bottom hole is fitted for a 14mm bolt the top one is not which gives you some play room to move the hub. Place the new bolt in, push the hub in for max cambers, and tighten that shit to 119 ft*lbs. Its not going anywhere.

I don't recommend however adjusting camber like this. Its best just to max it out and if you want more or less use top camber plates. A degree will be plenty for daily.

JS + BRZ · 03-11-2014, 02:29 PM

I have not actually. haha Thanks for the information.

Just found a local bud who is selling his brand new 14mm whiteline bolts. I'll use that and get the alignment done.

Thanks again!

VuDism · 03-11-2014, 02:38 PM

Quote:

Originally Posted by fooddude

Just wanted to know: who has these available in gunmetal?

www.oakos.com

Wise · 03-13-2014, 10:12 PM

Finally put my wheels on today.

17x9 +35 RPF1 wrapped in 235/40/17 Kumho KU31. Nuts are Muteki Closed End.

The front is a bit monster truck mode at the moment but that'll be fixed on tuesday when the camber bolts and Eibach Pro Kit springs go on.

VuDism · 03-16-2014, 08:46 PM

Rain. Sun. Snow. Daily Driver.

17x9 +35 : 245/40/17 Hankook Ventus S1 Noble 2
RS*R Super down Springs
Whiteline camber bolt. ~ -1.6 front camber

ikarus · 03-17-2014, 01:37 AM

Just got 17x9 Enkei RPF1s in matte bronze, wrapped in Bridgestone Potenza Pole Position S-04 in 245/40/17. Loving it!

Scottemad123 · 03-17-2014, 11:30 AM

Quote:

Originally Posted by JS + BRZ

So if I get two camber bolts, can I add in some negative camber? I have 245 40 rs3 on my +35 rpf1s.

Thank you!

Sent from my SCH-I605

Curious for side shots as I would have to run stock suspension for a while as well. Looks good so far!

JS + BRZ · 03-17-2014, 11:59 AM

Quote:

Originally Posted by Scottemad123

Curious for side shots as I would have to run stock suspension for a while as well. Looks good so far!

Here you go!

Name: uploadfromtaptalk1395068343324.jpg
Views: 4325
Size: 123.6 KB

Sent from my SCH-I605

VuDism · 03-17-2014, 02:06 PM

leicaboss · 03-17-2014, 02:10 PM

Quote:

Originally Posted by VuDism

Nice, I'm interested in seeing more white twins on the gunmetal RPF1's...

03-11-2014, 06:22 AM	#353
Squishy86 Senior Member Join Date: Jul 2012 Drives: Your Car Location: San Diego Posts: 439 Thanks: 461 Thanked 225 Times in 115 Posts Mentioned: 5 Post(s) Tagged: 0 Thread(s)	Camber bolts will give you about a degree to a degree and a half. I did that and almost maxed out my camber plates for 2.5 degrees. Sent from my SAMSUNG-SGH-I337 using Tapatalk __________________ http://instagram.com/squishy_86

03-16-2014, 08:46 PM	#359
VuDism NASIOC: AzNSTiImpreza Join Date: Sep 2013 Drives: 2013 Whiteout Scion FRS Location: Clarksburg, MD Posts: 276 Thanks: 81 Thanked 173 Times in 70 Posts Mentioned: 6 Post(s) Tagged: 0 Thread(s)	snowing Rain. Sun. Snow. Daily Driver. 17x9 +35 : 245/40/17 Hankook Ventus S1 Noble 2 RSR Super down Springs Whiteline camber bolt. ~ -1.6 front camber __________________ My Build Thread: VuDism's WHITEOUT FRS Daily Driver Journal nVu Films Website FACEBOOK - nVu Films YOUTUBE - nVu Films INSTAGRAM - nVu Films Last edited by VuDism; 03-17-2014 at 02:06 PM.*

03-17-2014, 02:06 PM	#363
VuDism NASIOC: AzNSTiImpreza Join Date: Sep 2013 Drives: 2013 Whiteout Scion FRS Location: Clarksburg, MD Posts: 276 Thanks: 81 Thanked 173 Times in 70 Posts Mentioned: 6 Post(s) Tagged: 0 Thread(s)	__________________ My Build Thread: VuDism's WHITEOUT FRS Daily Driver Journal nVu Films Website FACEBOOK - nVu Films YOUTUBE - nVu Films INSTAGRAM - nVu Films

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wheel Directory: Enkei RPF1 17x9.0 +45	LevinPhan	Wheels \| Tires \| Spacers \| Hub -- Sponsored by The Tire Rack	265	06-04-2024 12:13 PM
Group Buy: Enkei RPF1 17x9 +35, 17x9.5 +38, 18x9.5 +38 *In Stock*	LSD Motorsports	Groupbuys	246	08-29-2013 02:35 PM
WHITE Enkei NT03+M 18x9.5 / Enkei RPF1 17x9	Touge Factory	Wheels and Tires	2	02-05-2013 05:53 PM

03-10-2014, 06:09 PM	#351
JS + BRZ Banned Join Date: Dec 2013 Drives: 2010 MS3 Location: Los Angeles Posts: 1,820 Thanks: 1,180 Thanked 1,161 Times in 597 Posts Mentioned: 18 Post(s) Tagged: 0 Thread(s)	Woot woot.

03-11-2014, 01:44 AM	#352
JS + BRZ Banned Join Date: Dec 2013 Drives: 2010 MS3 Location: Los Angeles Posts: 1,820 Thanks: 1,180 Thanked 1,161 Times in 597 Posts Mentioned: 18 Post(s) Tagged: 0 Thread(s)	So if I get two camber bolts, can I add in some negative camber? I have 245 40 rs3 on my +35 rpf1s. Thank you! Sent from my SCH-I605

03-11-2014, 01:14 PM	#354
JS + BRZ Banned Join Date: Dec 2013 Drives: 2010 MS3 Location: Los Angeles Posts: 1,820 Thanks: 1,180 Thanked 1,161 Times in 597 Posts Mentioned: 18 Post(s) Tagged: 0 Thread(s)	Is there a difference in camber I can get with 14mm and 16mm bolt?

03-11-2014, 02:29 PM	#356
JS + BRZ Banned Join Date: Dec 2013 Drives: 2010 MS3 Location: Los Angeles Posts: 1,820 Thanks: 1,180 Thanked 1,161 Times in 597 Posts Mentioned: 18 Post(s) Tagged: 0 Thread(s)	I have not actually. haha Thanks for the information. Just found a local bud who is selling his brand new 14mm whiteline bolts. I'll use that and get the alignment done. Thanks again!

03-17-2014, 01:37 AM	#360
ikarus Member Join Date: Nov 2013 Drives: SWP BRZ 6MT Location: SLC/UT Posts: 15 Thanks: 5 Thanked 11 Times in 5 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Just got 17x9 Enkei RPF1s in matte bronze, wrapped in Bridgestone Potenza Pole Position S-04 in 245/40/17. Loving it!

User Name		Remember Me?
Password