Innovate Install Help - Vacuum Routing - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

swift996 · 07-12-2013, 09:53 PM

Does anyone have a diagram of the vacuum routing? I messed up somewhere as I expected because the directions are non-existent for the hose extensions. I have no idea where I went wrong.

[ame="http://www.youtube.com/watch?v=EgECuQE5VBg"]Innovate install - YouTube[/ame]

whataboutbob · 07-12-2013, 10:01 PM

To the throttle body there are 2 hoses. 1 from the front top of the motor, one from the rear right of the motor near the brake master cylinder. The extra hose that is larger in diameter goes to the intake tube. If you look at the tube, there is a fitting that it will slide over.

swift996 · 07-12-2013, 10:02 PM

I traced one...I misspoke when I say MAF extension I meant throttle body extension (loom)

[ame="http://www.youtube.com/watch?v=HtuWF196XhI"]Innovate install 2 - YouTube[/ame]

swift996 · 07-12-2013, 10:04 PM

Quote:

Originally Posted by whataboutbob

To the throttle body there are 2 hoses. 1 from the front top of the motor, one from the rear right of the motor near the brake master cylinder. The extra hose that is larger in diameter goes to the intake tube. If you look at the tube, there is a fitting that it will slide over.

Thanks, see the second video, is that the correct line? Should that be routed through the front and to the throttle body?

whataboutbob · 07-12-2013, 10:09 PM

I replaced both of those hoses with the ones supplied in the kit. Measure your hoses and compare the lengths to those called out in the directions. 25.4mm/1inch.

I routed both hoses around from the back to the throttle body.

swift996 · 07-12-2013, 11:20 PM

Thanks for the help, I'm calling it a night about 85-90% done. Too many dropped bolts, cuts and trying to understand how things go back together.

v1ru5 · 07-12-2013, 11:39 PM

Requires more beer

Carwhisperer · 07-13-2013, 12:11 AM

Quote:

Originally Posted by v1ru5

Requires more beer

I like.

evo4g63 · 07-13-2013, 01:21 AM

Quote:

Originally Posted by swift996

Thanks for the help, I'm calling it a night about 85-90% done. Too many dropped bolts, cuts and trying to understand how things go back together.

What time did you start your install?

xxscaxx · 07-13-2013, 01:46 AM

@swift996 - that second video, that hose you traced is for the heater hose. that one goes to the bottom port (one facing out toward you) of the throttle body.

The other heater hose is attached at the back of the block, and goes to the top port of the throttle body.

The only other lines are coming off the Evap solenoid (one goes to the fuel evap hard line, the other goes to the port on the back of the supercharger - one on the driver side).

In that first video, that line in the back is one of the stock lines that was attached to the stock intake manifold under the cover which is the crankcase line. That goes to the brass barb on the supercharger.

The other barb (on the passenger side) on the supercharger is for the brake booster.

Thats should be everything if i'm not mistaken.

PS - read the directions a couple of times. Its not completely straight forward but all the answers are in there. I wish I took some pics because I would have done a DIY for it.

Dezoris · 07-13-2013, 05:11 AM

Smart you took a break. tired and frustrated equal more mistakes and stress.

swift996 · 07-13-2013, 08:28 AM

I did about 5hrs of work last night, probably have another hour this morning. It was pretty dark too (I usually work in sun light). I had a light but it's still not the same. With the vacuum lines, they could have easily labeled them or put a plastic indicator around them. I think one of the tougher parts so far was keeping all the wiring and hoses under the supercharger. Other than that just a lot of tight quarters around the injectors, injector covers, bolts for the manifold, etc. I also wish they have a few more pics/diagrams in the instructions, most of it's straight forward but in a few areas it will just say install _____ w/o a pic that could be helpful. This is my first time doing something like this, but I do everything else with my car, so I know my way around.

Foobar · 07-13-2013, 09:09 AM

Quote:

Originally Posted by swift996

I did about 5hrs of work last night, probably have another hour this morning.

So are you back in business now or still need help?

whataboutbob · 07-13-2013, 09:52 AM

Let me know if you get stuck on anything and I'll try to help.

07-12-2013, 09:53 PM	#1
swift996 Senior Member Join Date: Nov 2011 Drives: Subaru BRZ Limited 6MT Location: Winston-Salem, NC Posts: 2,432 Thanks: 712 Thanked 955 Times in 545 Posts Mentioned: 47 Post(s) Tagged: 0 Thread(s)	Innovate Install Help - Vacuum Routing Does anyone have a diagram of the vacuum routing? I messed up somewhere as I expected because the directions are non-existent for the hose extensions. I have no idea where I went wrong. [ame="http://www.youtube.com/watch?v=EgECuQE5VBg"]Innovate install - YouTube[/ame] __________________ Innovate Supercharged Black Limited BRZ 6-Speed MT(Build Thread) 2010 Cadillac CTS-V Sedan M6 w/550whp (Build Thread) Last edited by swift996; 07-13-2013 at 08:32 AM.

07-12-2013, 10:02 PM	#3
swift996 Senior Member Join Date: Nov 2011 Drives: Subaru BRZ Limited 6MT Location: Winston-Salem, NC Posts: 2,432 Thanks: 712 Thanked 955 Times in 545 Posts Mentioned: 47 Post(s) Tagged: 0 Thread(s)	I traced one...I misspoke when I say MAF extension I meant throttle body extension (loom) [ame="http://www.youtube.com/watch?v=HtuWF196XhI"]Innovate install 2 - YouTube[/ame] __________________ Innovate Supercharged Black Limited BRZ 6-Speed MT(Build Thread) 2010 Cadillac CTS-V Sedan M6 w/550whp (Build Thread)

07-12-2013, 11:20 PM	#6
swift996 Senior Member Join Date: Nov 2011 Drives: Subaru BRZ Limited 6MT Location: Winston-Salem, NC Posts: 2,432 Thanks: 712 Thanked 955 Times in 545 Posts Mentioned: 47 Post(s) Tagged: 0 Thread(s)	Thanks for the help, I'm calling it a night about 85-90% done. Too many dropped bolts, cuts and trying to understand how things go back together. __________________ Innovate Supercharged Black Limited BRZ 6-Speed MT(Build Thread) 2010 Cadillac CTS-V Sedan M6 w/550whp (Build Thread)

07-13-2013, 01:46 AM	#10
xxscaxx Senior Member Join Date: Jul 2012 Drives: 2013 SWP BRZ Location: New York Posts: 2,240 Thanks: 458 Thanked 878 Times in 556 Posts Mentioned: 34 Post(s) Tagged: 0 Thread(s)	@swift996 - that second video, that hose you traced is for the heater hose. that one goes to the bottom port (one facing out toward you) of the throttle body. The other heater hose is attached at the back of the block, and goes to the top port of the throttle body. The only other lines are coming off the Evap solenoid (one goes to the fuel evap hard line, the other goes to the port on the back of the supercharger - one on the driver side). In that first video, that line in the back is one of the stock lines that was attached to the stock intake manifold under the cover which is the crankcase line. That goes to the brass barb on the supercharger. The other barb (on the passenger side) on the supercharger is for the brake booster. Thats should be everything if i'm not mistaken. PS - read the directions a couple of times. Its not completely straight forward but all the answers are in there. I wish I took some pics because I would have done a DIY for it. Last edited by xxscaxx; 07-13-2013 at 02:06 AM.

07-13-2013, 05:11 AM	#11
Dezoris Senior Member Join Date: Aug 2012 Drives: FR-S Location: IL Posts: 2,857 Thanks: 519 Thanked 2,998 Times in 1,095 Posts Mentioned: 159 Post(s) Tagged: 1 Thread(s)	Smart you took a break. tired and frustrated equal more mistakes and stress. __________________ SAVAGEGEESE

07-12-2013, 11:39 PM	#7
v1ru5 Senior Member Join Date: May 2013 Drives: BRZ D4S 6MT L Vortech Location: Falls Church, VA Posts: 387 Thanks: 168 Thanked 152 Times in 108 Posts Mentioned: 30 Post(s) Tagged: 2 Thread(s)	Requires more beer

07-13-2013, 08:28 AM	#12
swift996 Senior Member Join Date: Nov 2011 Drives: Subaru BRZ Limited 6MT Location: Winston-Salem, NC Posts: 2,432 Thanks: 712 Thanked 955 Times in 545 Posts Mentioned: 47 Post(s) Tagged: 0 Thread(s)	I did about 5hrs of work last night, probably have another hour this morning. It was pretty dark too (I usually work in sun light). I had a light but it's still not the same. With the vacuum lines, they could have easily labeled them or put a plastic indicator around them. I think one of the tougher parts so far was keeping all the wiring and hoses under the supercharger. Other than that just a lot of tight quarters around the injectors, injector covers, bolts for the manifold, etc. I also wish they have a few more pics/diagrams in the instructions, most of it's straight forward but in a few areas it will just say install _____ w/o a pic that could be helpful. This is my first time doing something like this, but I do everything else with my car, so I know my way around. __________________ Innovate Supercharged Black Limited BRZ 6-Speed MT(Build Thread) 2010 Cadillac CTS-V Sedan M6 w/550whp (Build Thread)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Innovate SC Install, Testing & Tuning	Xero-Limit	Forced Induction	231	01-23-2015 01:32 PM
Innovate Supercharger!!!	Titanmotorsports	Forced Induction	62	08-24-2014 11:25 PM
Innovate questions	Fast_Freddy	Forced Induction	12	07-02-2013 03:27 PM
innovate SC for sale	kioton32	Forced Induction	4	04-08-2013 12:42 PM
FS: Innovate Motorsports OT-2	pixel67	Engine, Exhaust, Bolt-Ons	0	01-05-2013 11:13 AM

User Name		Remember Me?
Password