Stock Rear View Camera for Fujitsu Ten?

[xcelir8brz]

Still nothing works. Hmmm. Pin 17. Color pink. Right?

[Foobar]

Originally Posted by xcelir8brz

Still nothing works. Hmmm. Pin 17. Color pink. Right?

Pink with a green stripe. I've tested this with navigation input, DivX movie playing, and going into settings while the vehicle was in motion. I did not test phone input - maybe that uses an additional nanny signal? Try some of these other functions.

[xcelir8brz]

Originally Posted by Foobar

None of the other options did anything for me. I could adjust them but they don't affect the rearview camera display.

I don't think I tried scrolling it out completely, let me give that a shot.

I tried everything regarding this and no go. Stuck with the lines.

[xcelir8brz]

Originally Posted by Foobar

Pink with a green stripe. I've tested this with navigation input, DivX movie playing, and going into settings while the vehicle was in motion. I did not test phone input - maybe that uses an additional nanny signal? Try some of these other functions.

Maybe it's the radio's firmware? Yup, I used the correct wire, cut it, and put a toggle serially in the middle. Hmmm...

[xcelir8brz]

Originally Posted by xcelir8brz

I ended up ordering the VTL425 from Amazon. Then I changed the mine and ordered this instead VTK200C:

http://visiontechamerica.com/site/portfolio/vtk200c/

I figured I'd mount this in the OEM location and then wouldn't have to worry about the lines as it would be damn near exact. Was cheaper than the VTL425 also.

I decided that when I receive this, I'll mount it in place of the left (drivers) side license plate screw location. Ill also swap out the right (passengers) side license plate screw location with a bolt. This will keep it the most clean rather than spending time mounting it OEM and that's a permanent change. Hmmm. We'll see when I get it, but that's the plan for now and what this product was intended for.

[Foobar]

Originally Posted by xcelir8brz

Maybe it's the radio's firmware? Yup, I used the correct wire, cut it, and put a toggle serially in the middle. Hmmm...

So with the toggle off, your menu shows the phone/settings/video available while stopped, but as soon as you start moving, it becomes disabled? If so, that would indicate to me that the vehicle speed sensor signal is not disconnected. Try it without the switch, leaving the wire completely disconnected?

Only thing else I have done is grounded the e-brake line on the 16-pin, but that shouldn't be necessary for phone/navigation/settings. That's only used for video playback as far as I know.

[Flat Black VW]

Originally Posted by Foobar

Pink with a green stripe. I've tested this with navigation input, DivX movie playing, and going into settings while the vehicle was in motion. I did not test phone input - maybe that uses an additional nanny signal? Try some of these other functions.

I double checked today and mine does do phone also.

[sure74]

Originally Posted by Foobar

That's the Rydeen Duo, right? Let me know how that works out for you

Just posted some pics on the camera installation:

http://www.ft86club.com/forums/showthread.php?t=17020

[xcelir8brz]

Just replaced the Pyle license plate cyborg camera with a Boyo. Looks 100x better and stock! Adjusted the backup lines as well.

Take a look:

[Furtive]

Originally Posted by xcelir8brz

Just replaced the Pyle license plate cyborg camera with a Boyo. Looks 100x better and stock! Adjusted the backup lines as well.

i just bought a boyo vtk360 .. hopefully it will work.. specs on it seem a little bit better than the boyo you bought xcelir8br

..also which link on ae64 is the right cord for the brz ?

[Furtive]

Originally Posted by Foobar

(use an add-a-circuit to tap into power).

which fuse should I tap into?

[Foobar]

Originally Posted by Furtive

which fuse should I tap into?

Whichever's convenient and driven off of ACC, not always live or you'll kill your camera sooner. Just use the same amp fuse rating on the bottom slot of the add-a-circuit, since that replaces the functionality. The top slot goes to the new circuit.

I used the seat heater fuse.

[xcelir8brz]

Originally Posted by Furtive

i just bought a boyo vtk360 .. hopefully it will work.. specs on it seem a little bit better than the boyo you bought xcelir8br

..also which link on ae64 is the right cord for the brz ?

But where are you going to mount it? It requires a large hole.

[Furtive]

Originally Posted by xcelir8brz

But where are you going to mount it? It requires a large hole.

I was thinking the original camera location.. (i didnt see the size specs on it.. but I hope fits) if not. I may just return and get something like yours.

Did you use SVXdc wires?