Official FT86Club 3D printing thread! - Page 23 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Pat · 01-09-2025, 03:27 PM

How was the aero device attached to the side mirror developed? It's interesting to me as it is different than the Verus unit.

DocWalt · 01-09-2025, 05:51 PM

Quote:

Originally Posted by Pat

How was the aero device attached to the side mirror developed? It's interesting to me as it is different than the Verus unit.

"it looks cool"

I'll be messing around various "wing" portions of the design to see what helps the most with buffeting. As it is now, minimal buffeting with both windows down at ~95 mph. I think that's less effective than the "flap" style that Verus sells. I did a design for that ages ago and never bothered actually installing them, but I could test back to back to back.

RBenz13 · 01-12-2025, 01:04 PM

Does anyone have a scan/STL of the entire center console (1st Gen)? I'd like to play around with some ideas in Fusion.

Racecomp Engineering · 01-16-2025, 01:15 PM

Quote:

Originally Posted by DocWalt

Designed and printed some stuff inspired by @makinen and his prints.

Battery adapter for my Noco NLP20:

Any concerns about cold weather use or charging with the LiFePO4 battery?

My 20 lb deka AGM battery died because I was away a lot during the holidays and it's been so butt ass cold. I was tempted to replace with a LiFePO4 but got nervous...and after a jump my deka seems totally fine. That thing is awesome honestly. But I'm still thinking about it.

- Andrew

DocWalt · 01-16-2025, 05:15 PM

Quote:

Originally Posted by Racecomp Engineering

Any concerns about cold weather use or charging with the LiFePO4 battery?

My 20 lb deka AGM battery died because I was away a lot during the holidays and it's been so butt ass cold. I was tempted to replace with a LiFePO4 but got nervous...and after a jump my deka seems totally fine. That thing is awesome honestly. But I'm still thinking about it.

- Andrew

Seems fine so far. When it's super cold, it seems to take a little bit to warm up the battery. I'd probably do an NLP30 for actual use, this is actually my wife's autocross car's battery.

boi · 10-13-2025, 03:35 AM

Has anyone ever tried making the aero stabilizer that goes into the gap at the trunk and rear window?

smackrel · 10-13-2025, 02:24 PM

Quote:

Originally Posted by boi

Has anyone ever tried making the aero stabilizer that goes into the gap at the trunk and rear window?

That would be awesome!

I have never seen this part in person, does it just stick on with adhesive?

boi · 10-15-2025, 10:33 AM

Quote:

Originally Posted by smackrel

That would be awesome!

I have never seen this part in person, does it just stick on with adhesive?

Yes it attaches with adhesive of i can get my hands on one i would scan it for the group or sell for 200+ on e bay not sure why they are so expensive which sucks

smackrel · 10-15-2025, 12:19 PM

It's on sale at BHJ for $105 right now

https://www.blackhawkjapan.com/products/trd-ms346-18001

Dadhawk · 10-20-2025, 10:51 AM

Been getting into some 3D printing recently. Purchased a Creality K2 Plus with a CMS expansion so I can print up to four colors in one print.

Car related, I have a 70 piece Craftsman tool set I've had since high school (about 45 years). The plastic case finally feel apart so I decided to move this into a newer toolbox and use an open source organization system call Gridfinity to print replacement holders.

This isn't the most efficient space wise but it allows me to quickly ID sockets which is the idea behind Gridfinity (quick access, immediately tell what is missing).

This is most of the set ready to go. Discounting the printer cost, the filament cost was about $10 for all of it.

makinen · Today, 03:05 AM

Quote:

Originally Posted by Racecomp Engineering

Any concerns about cold weather use or charging with the LiFePO4 battery?

Actually I was suffered when cold before adding heat protection walls.

Name: 20231101_210333(1).jpg
Views: 11
Size: 401.1 KB

Battery, heat protection foam, a printed wall with almost void inside, heat protection foam.

10-20-2025, 10:51 AM	#318
Dadhawk Senior Member Join Date: Feb 2012 Drives: '13 FR-S (#3 of 1st 86) Location: Powder Springs, GA Posts: 20,088 Thanks: 39,612 Thanked 25,409 Times in 11,587 Posts Mentioned: 187 Post(s) Tagged: 4 Thread(s)	Been getting into some 3D printing recently. Purchased a Creality K2 Plus with a CMS expansion so I can print up to four colors in one print. Car related, I have a 70 piece Craftsman tool set I've had since high school (about 45 years). The plastic case finally feel apart so I decided to move this into a newer toolbox and use an open source organization system call Gridfinity to print replacement holders. This isn't the most efficient space wise but it allows me to quickly ID sockets which is the idea behind Gridfinity (quick access, immediately tell what is missing). This is most of the set ready to go. Discounting the printer cost, the filament cost was about $10 for all of it. Attached Images __________________ Olivia 05/03/2012 - 01/06/2024. 231,146 glorious miles. Visit my Owner's Journal where I wax philosophic on all things FR-S Post your 86 or see others in front of a(n) (in)famous landmark. What fits in your 86? Show us the "Junk In Your Trunk".

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Official DTM Autobody Services Thread for FT86Club!	DTMAUTOBODY	Southern California	9	12-31-2013 03:09 PM
Official FT86Club Chatroom?	wrxgoose	Site Announcements / Questions / Issues	13	09-15-2012 06:26 PM
Official FT86Club decal idea?	Hanzo	Scion FR-S / Toyota 86 GT86 General Forum	71	06-21-2012 09:09 PM

01-12-2025, 01:04 PM	#311
RBenz13 Custom User Title Join Date: Jan 2018 Drives: '13 SWP MT BRZ Ltd Location: Fort Bragg, NC Posts: 40 Thanks: 9 Thanked 13 Times in 8 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Does anyone have a scan/STL of the entire center console (1st Gen)? I'd like to play around with some ideas in Fusion.

10-13-2025, 03:35 AM	#314
boi Junior Member Join Date: Apr 2017 Drives: 2013 Brz Location: Pa Posts: 8 Thanks: 0 Thanked 1 Time in 1 Post Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Has anyone ever tried making the aero stabilizer that goes into the gap at the trunk and rear window?

10-15-2025, 12:19 PM	#317
smackrel Full Throttle! Join Date: Nov 2021 Drives: 17 CBSP Limited PP Location: TPA Posts: 85 Thanks: 62 Thanked 32 Times in 27 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	It's on sale at BHJ for $105 right now https://www.blackhawkjapan.com/products/trd-ms346-18001

User Name		Remember Me?
Password