Verus' Shop BRZ - Development Thread - Page 11 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

VerusEric · 10-27-2016, 12:45 PM

Been extremely busy with SEMA fast approaching but I did finish up a blog post I've been wanting to complete for awhile now.

The blog post explains the difference between high-performance fans and low profile fans. There is some good information in it, definitely worth a read for anyone looking at a fan setup in this chassis.

http://www.velox-motorsports.com/sin...nd-Information

Thanks,
Eric

ichitaka05 · 10-27-2016, 12:48 PM

Quote:

Originally Posted by VeloxEric

Been extremely busy with SEMA fast approaching but I did finish up a blog post I've been wanting to complete for awhile now.

The blog post explains the difference between high-performance fans and low profile fans. There is some good information in it, definitely worth a read for anyone looking at a fan setup in this chassis.

http://www.velox-motorsports.com/sin...nd-Information

Thanks,
Eric

You guys gonna be at the SEMA?

VerusEric · 10-28-2016, 11:10 PM

Quote:

Originally Posted by ichitaka05

You guys gonna be at the SEMA?

Only myself. I'll be there walking around, not as an exhibitor. Our full crew will be at PRI though.

Been helping out Full-Race with their build the past few weeks. Wrapping it up tomorrow in true SEMA fashion haha.

Thanks,
Eric

VerusEric · 10-30-2016, 07:27 PM

Received some more photos from the event through Desert Street Scene and Omega Motorsports.

After SEMA I hope to get into the garage and finally get some custom fabrication done that I've been wanting to do for a while now.

Thanks,
Eric

VerusEric · 11-09-2016, 02:39 PM

Wing Wednesday, we're working on developing our own wing profile using ANSYS

.

Thanks,
Eric

VerusEric · 11-15-2016, 02:26 PM

We've officially released the carbon thermoplastic kit: http://www.ft86club.com/forums/showthread.php?t=112898

Adjustable front splitter

Adjustable side splitter/skirts

Some photos while doing some more upgrades in the coming week(s):

Looking forward to getting the AP brake kit on shortly and the motor mounts on as well.

Thanks,
Eric

VerusEric · 11-21-2016, 01:23 AM

Had some free time while my computer's hard drive took a dump on me, and I got the upgraded motor mounts in the car. With the oil drain in the way for the driver's side, I'm really glad I had the transmission out at the same time.

This is what happens when the trans/engine plug on top of the engine gets hot enough and drops into the bell housing. Didn't hear anything, nor did it ruin drive ability or operation. I was just checking up on the clutch fork and looking at the TOB for some quick routine maintenance and testing and saw this. Cleaned most of it off with a bit of brake cleaner.

*I highly recommend removing it if you're tracking the car or are FI. It will fall in and it will make a mess.*

Thanks,
Eric

djwishbone · 11-21-2016, 01:05 PM

Are you talking about this piece?

Is there any issue with removing it?

Would love to see the Velox wing!

Takumi788 · 11-22-2016, 08:21 AM

Quote:

Originally Posted by djwishbone

Are you talking about this piece?
Is there any issue with removing it?

Would love to see the Velox wing!

Your pic is not working.

VerusEric · 11-23-2016, 02:11 AM

Grabbed a shot of the new J-hook rotor replacements. They are awesome quality as expected from AP Racing/Essex. I also bought new NAS hardware.

While the front end was off last weekend, I added some mesh to the fog light inlets. It's not very noticeable, it shouldn't impede flow, and will catch anything large that otherwise may make its way to the rotor.

I sandwiched it between the fog light duct and the 3" hose. The hose clamp holds it in place and it is holding up well so far.

Thanks,
Eric

VerusEric · 11-27-2016, 11:46 PM

Got a bit of design work done over Thanksgiving weekend in between a lot of shipping. Designed and rapid prototyped a bell housing cover for the FA20.

Design

Slicer screenshot (creating the gcode for how the printer will print)

Design on mock-up engine we have laying around.

Thanks,
Eric

djwishbone · 11-29-2016, 12:58 PM

Nice! If anyone misses why this is necessary look at the last post. Want!

flixonase · 11-29-2016, 01:25 PM

Quote:

Originally Posted by VeloxEric

*I highly recommend removing it if you're tracking the car or are FI. It will fall in and it will make a mess.*

Hey Eric,

I'm using my car for the track only. Never had the engine or transmission out of the car so I have no idea what is shown in the pictures... But I take your recommendation seriously.

Which part needs to be removed? Can you please elaborate?

Thank you very much!

djwishbone · 11-29-2016, 01:43 PM

Quote:

Originally Posted by flixonase

Hey Eric,

I'm using my car for the track only. Never had the engine or transmission out of the car so I have no idea what is shown in the pictures... But I take your recommendation seriously.

Which part needs to be removed? Can you please elaborate?

Thank you very much!

Look at my post right below his, I circled it. You can see it from the top of the engine in the very back under the hood. It's comes out alarmingly easily, just a rubber piece sitting in there.

You can't see it in this picture but this is where it's at.

10-30-2016, 07:27 PM	#144
VerusEric Join Date: Mar 2015 Drives: BRZ, STI, GT350R, Supra, 987.2 Location: Indiana Posts: 1,146 Thanks: 567 Thanked 2,529 Times in 780 Posts Mentioned: 87 Post(s) Tagged: 3 Thread(s)	Received some more photos from the event through Desert Street Scene and Omega Motorsports. After SEMA I hope to get into the garage and finally get some custom fabrication done that I've been wanting to do for a while now. Thanks, Eric Last edited by VerusEric; 09-17-2017 at 10:02 PM.

11-21-2016, 01:05 PM	#148
djwishbone Last Starfighter Join Date: Jul 2016 Drives: 2016 FR-S Series 2.0 Location: Sonoran Desert Posts: 118 Thanks: 36 Thanked 43 Times in 29 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Are you talking about this piece? Is there any issue with removing it? Would love to see the Velox wing! Last edited by djwishbone; 11-21-2016 at 01:33 PM.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Verus Engineering Rear Wing Development	VerusEric	Tracking / Autocross / HPDE / Drifting	203	07-05-2021 10:15 AM
FRS / BRZ Intake Manifold - Development Thread - FT-86SpeedFactory by Velox	FT-86 SpeedFactory	Engine, Exhaust, Transmission	733	12-11-2018 11:13 PM
Hancha BRZ/FR-S/GT86 Aero Parts Development Thread	Hancha Group	Cosmetic Modification (Interior/Exterior/Lighting)	57	03-24-2014 06:40 PM
Raceseng \| Development FT86 \| Build Thread	Raceseng	Member's Car Journals	17	06-06-2013 10:22 AM

10-27-2016, 12:45 PM	#141
VerusEric Join Date: Mar 2015 Drives: BRZ, STI, GT350R, Supra, 987.2 Location: Indiana Posts: 1,146 Thanks: 567 Thanked 2,529 Times in 780 Posts Mentioned: 87 Post(s) Tagged: 3 Thread(s)	Been extremely busy with SEMA fast approaching but I did finish up a blog post I've been wanting to complete for awhile now. The blog post explains the difference between high-performance fans and low profile fans. There is some good information in it, definitely worth a read for anyone looking at a fan setup in this chassis. http://www.velox-motorsports.com/sin...nd-Information Thanks, Eric

11-09-2016, 02:39 PM	#145
VerusEric Join Date: Mar 2015 Drives: BRZ, STI, GT350R, Supra, 987.2 Location: Indiana Posts: 1,146 Thanks: 567 Thanked 2,529 Times in 780 Posts Mentioned: 87 Post(s) Tagged: 3 Thread(s)	Wing Wednesday, we're working on developing our own wing profile using ANSYS . Thanks, Eric

11-15-2016, 02:26 PM	#146
VerusEric Join Date: Mar 2015 Drives: BRZ, STI, GT350R, Supra, 987.2 Location: Indiana Posts: 1,146 Thanks: 567 Thanked 2,529 Times in 780 Posts Mentioned: 87 Post(s) Tagged: 3 Thread(s)	We've officially released the carbon thermoplastic kit: http://www.ft86club.com/forums/showthread.php?t=112898 Adjustable front splitter Adjustable side splitter/skirts Some photos while doing some more upgrades in the coming week(s): Looking forward to getting the AP brake kit on shortly and the motor mounts on as well. Thanks, Eric

11-21-2016, 01:23 AM	#147
VerusEric Join Date: Mar 2015 Drives: BRZ, STI, GT350R, Supra, 987.2 Location: Indiana Posts: 1,146 Thanks: 567 Thanked 2,529 Times in 780 Posts Mentioned: 87 Post(s) Tagged: 3 Thread(s)	Had some free time while my computer's hard drive took a dump on me, and I got the upgraded motor mounts in the car. With the oil drain in the way for the driver's side, I'm really glad I had the transmission out at the same time. This is what happens when the trans/engine plug on top of the engine gets hot enough and drops into the bell housing. Didn't hear anything, nor did it ruin drive ability or operation. I was just checking up on the clutch fork and looking at the TOB for some quick routine maintenance and testing and saw this. Cleaned most of it off with a bit of brake cleaner. I highly recommend removing it if you're tracking the car or are FI. It will fall in and it will make a mess. Thanks, Eric

11-23-2016, 02:11 AM	#150
VerusEric Join Date: Mar 2015 Drives: BRZ, STI, GT350R, Supra, 987.2 Location: Indiana Posts: 1,146 Thanks: 567 Thanked 2,529 Times in 780 Posts Mentioned: 87 Post(s) Tagged: 3 Thread(s)	Grabbed a shot of the new J-hook rotor replacements. They are awesome quality as expected from AP Racing/Essex. I also bought new NAS hardware. While the front end was off last weekend, I added some mesh to the fog light inlets. It's not very noticeable, it shouldn't impede flow, and will catch anything large that otherwise may make its way to the rotor. I sandwiched it between the fog light duct and the 3" hose. The hose clamp holds it in place and it is holding up well so far. Thanks, Eric

11-27-2016, 11:46 PM	#151
VerusEric Join Date: Mar 2015 Drives: BRZ, STI, GT350R, Supra, 987.2 Location: Indiana Posts: 1,146 Thanks: 567 Thanked 2,529 Times in 780 Posts Mentioned: 87 Post(s) Tagged: 3 Thread(s)	Got a bit of design work done over Thanksgiving weekend in between a lot of shipping. Designed and rapid prototyped a bell housing cover for the FA20. Design Slicer screenshot (creating the gcode for how the printer will print) Design on mock-up engine we have laying around. Thanks, Eric

11-29-2016, 12:58 PM	#152
djwishbone Last Starfighter Join Date: Jul 2016 Drives: 2016 FR-S Series 2.0 Location: Sonoran Desert Posts: 118 Thanks: 36 Thanked 43 Times in 29 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Nice! If anyone misses why this is necessary look at the last post. Want!

User Name		Remember Me?
Password