OpenFlash Tablet: RomRaider parameters for Launch Control and Flat-foot Shift

[CaptainSlow]

OK thanks!

[CaptainSlow]

Tested it last night (I have a beta 1.4X tune on the car at the moment...need to update I guess)...can confirm launch control is active on those maps, and is set around the 5500 rpm range.

[2point0]

Does this go for TunerPro as well? I recall seeing the fields, but wasn't sure what to do with them.

[steve99]

Originally Posted by 2point0

Does this go for TunerPro as well? I recall seeing the fields, but wasn't sure what to do with them.

The parameters are defined for tunepro in the XDF files for C series ROM's (see first post be shiv for defined ROM's

If you open the XDF in notepad or similar text editor/viewer and search for them ie FFS or Launch their is some info on setting these parameters.

[CaptainSlow]

Edit...nevermind. I was being an idiot. Original post is quoted below, but I didn't want to leave my OP here because there was actually no issue other than user error.

[steve99]

Originally Posted by CaptainSlow

OK, bit of an issue (or maybe it's not...you be the judge).

I had a beta version of the 93 Octane Stage 1 1.42 map installed on my car. I tested it yesterday and found that it did indeed have launch control...with the clutch in the revs would not pass 5600RPM...here is a capture of the parameters for that tune file:



I downloaded the new released 1.42 maps today and modified the 93 Octane Stage 1 and E85 EL Stage 2 maps to have a LC setting of 3600 (would equate to a 4000 RPM limiter) and FFS of 600 (so the RPMs would max at 7000 when using FFS). I saved these new files as "93 Octane v1.42 (FFS+LC).bin" and "E85 v1.42 (FFS+LC).bin" - NOTE - I did actually type ".bin" at the end of the file name when I was naming it - didn't seem to automatically attach that file type when I didn't the first time. Not sure if that matters or not.

Here are the two sets of parameters:

93 Octane v1.42 (unmodified)



93 Octane v1.42 (modified FFS and LC)



I loaded the modified map onto my car, but the launch control doesn't seem to be working. I pushed the clutch in and tried revving, but it just revved near redline, so I just let up. Tried that a couple of times, but got the same results. The car wasn't fully warmed up...not sure if that matters? Anyway, just wondering what, if anything, might be going on? It's not a huge deal, but I would like to know why it's not working now.

I didn't try the base released v1.42 map as an intermediate, but like I said, it was working with the beta v1.42 map. Anyway, figured I probably did something wrong, so just wondering if anyone sees anything obvious or has an answer for what might be going on.

Thanks!

Did you also point Tunerpro at the "new" XDF file corresponding to the new bin files ??
Bin files and XDF's must match

[CaptainSlow]

Yeah...turns out im a moron. Im an idiot and accidentally flashed the stock file instead of the new tuned file. I thought I had selected it but I was wrong. Loaded it up again and it works like a charm...revs stay right at 4k

Sent from my GT-P5113 using Tapatalk

[Danklvr]

not supported for B01C roms yet - FYI if you have a B01C rom and are looking for this in RomRaider.

[Shiv@Openflash]

Originally Posted by Danklvr

not supported for B01C roms yet - FYI if you have a B01C rom and are looking for this in RomRaider.

Launch control and FFS does not supported in the new 2014 B series ROMs just yet.

[Proof]

Is there anyone who can walk me though getting Romraider to even friggin work?! I have been screwing around for two hours and cant get it to even open a file. I feel like a moron but cant cant seem to find what I am doing wrong. Are there any walk-thru?

[Proof]

Originally Posted by shiv@vishnu

Launch control and FFS does not supported in the new 2014 B series ROMs just yet.

I assume this applies to the 800C and timeline on this?

[DEK186]

Will flashing the same rom with different LC & FFS parameters require the ECU to learn trims again and so on?? I am thinking of saving a few roms with different LC & FFS parameters and flashing between them to test them out on the track this afternoon. Would hate to have a shit run down the quarter because my ECU hasn't learnt what it needs to in 400m.

[steve99]

Originally Posted by DEK186

Will flashing the same rom with different LC & FFS parameters require the ECU to learn trims again and so on?? I am thinking of saving a few roms with different LC & FFS parameters and flashing between them to test them out on the track this afternoon. Would hate to have a shit run down the quarter because my ECU hasn't learnt what it needs to in 400m.

Yes , your erasing then flashing entire ROM, it will need learning time

[t1ao]

Originally Posted by shiv@vishnu

Launch control and FFS does not supported in the new 2014 B series ROMs just yet.

I currently have B00C, would i be fine using A01C, so i could use launch control?