MAF Scaling - Open/Closed Loop Fueling info - Page 18 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

vgi · 10-03-2014, 07:59 PM

@Kodename47 thank you mate for all the awesome tools and help

steve99 · 10-03-2014, 10:47 PM

Quote:

Originally Posted by Kodename47

Just an FYI, I've updated my IAT tool (thanks @vgi) and instructions found here: Post 149

I reckon you need to start a kodename47,s tuning tools and utilites thread to reference them all in one place

Kodename47 · 10-04-2014, 03:44 AM

Quote:

Originally Posted by steve99

I reckon you need to start a kodename47,s tuning tools and utilites thread to reference them all in one place

I will do, I've just been finishing off my last one and made sure it all works. Now I need to set it up for RR before I post it since you all use that

Foobar · 11-03-2014, 02:14 PM

Quote:

Originally Posted by steve99

The OFT300 (Vortex supercharger) map uses the 2.5 BAR Omni and has CEL-P0068 disabled in the map
???

FYI - I don't think this is the case, as I threw a P0068 after test driving my OFT300 tune on Friday. I cleared the code and am waiting to see if it comes back.

Sent the log to Shiv so hopefully he can confirm if everything's good and that code just needs to be disabled in the tune.

Shiv confirmed log was good and just sent me the same tune but with P0068 disabled. Maybe he starts out with it turned on, but after the initial datalog confirmation he sends one with it off, just in case there are genuine MAP scaling issues?

Toyota John · 11-08-2014, 05:40 PM

Could anyone help me with removing the CL/OL delay in Romraider. Would like to confirm that I am changing the right tables to stop the LTFT for working.

steve99 · 12-12-2014, 08:19 AM

Added Grimspeed Intake MAF scaling to first post

MFB · 12-12-2014, 08:39 AM

Quote:

Originally Posted by vgi

@MFB mark?

Yes @vgi

yoruck · 12-12-2014, 09:40 AM

hi, just before a start trying to scal maf for my trd CAI
perhaps somebody have already do it?
i am interrested in

benlaz88 · 12-16-2014, 08:16 PM

Any AEM intake scaling yet?

vgi · 12-16-2014, 08:59 PM

Quote:

Originally Posted by MFB

Yes @vgi

bought a twin?

rcampici · 12-18-2014, 04:05 PM

With my OFT log I have Injection mode 2 and 3
This does not relate with the modes shown in this thread.
I need to know please what the two modes in OFT are
I am assuming 2 for CL and 3 for OL

Further using Mafscaling Master there is a value dV/dT what value are people using for this?

Thanks

steve99 · 12-18-2014, 05:17 PM

Quote:

Originally Posted by rcampici

With my OFT log I have Injection mode 2 and 3
This does not relate with the modes shown in this thread.
I need to know please what the two modes in OFT are
I am assuming 2 for CL and 3 for OL

Further using Mafscaling Master there is a value dV/dT what value are people using for this?

Thanks

Mate after the levels of apreciation you showed last time i tried to assist you in this thread

http://www.ft86club.com/forums/showthread.php?t=75339

i probably should not help
but lets try again
your logging the wrong parameter fuel injection mode is port\ direct injection
you need to log fuel system status for ol\cl fueling mode then you will get correct data

dv\dt is calculated by the vgi utility just accept the default

rcampici · 12-18-2014, 05:22 PM

Quote:

Originally Posted by steve99

Mate after the levels of apreciation you showed last time i tried to assist you in this thread

http://www.ft86club.com/forums/showthread.php?t=75339

i probably should not help
but lets try again
your logging the wrong parameter fuel injection mode is port\ direct injection
you need to log fuel system status for ol\cl fueling mode then you will get correct data

dv\dt is calculated by the vgi utility just accept the default

If I wanted to be abused once more by you I would have specifically asked you...
So please ignore my posts as I am asking those that provide accurate responses or just opinions with caveats unlike you

Koa · 12-18-2014, 05:33 PM

Quote:

Originally Posted by rcampici

If I wanted to be abused once more by you I would have specifically asked you...

Dude.. you've been acting like a complete douche about OFT. (refer: http://www.ft86club.com/forums/showpost.php?p=1971497&postcount=12 ) Now dismissing one of the people who has done so much for the community?

Kick rocks, seriously. Go put that "experience in programming and computers" to use and figure it out yourself

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
AFR in Closed Loop	Toyota John	Software Tuning	39	07-07-2019 08:26 AM
BRZedit Fuel Trims, Closed to Open loop transiton	mad_sb	Engine, Exhaust, Transmission	32	08-06-2015 03:14 AM
Notes on injector / maf scalining using full time open loop	mad_sb	Software Tuning	40	03-03-2014 05:49 PM
Screencast: closed loop boost control with RaceRom	jamesm	Software Tuning	2	02-10-2014 02:23 PM
Screencast: experimenting with full-time closed loop fueling	jamesm	Software Tuning	2	12-27-2013 10:19 AM

10-03-2014, 07:59 PM	#239
vgi Senior Member Join Date: Apr 2013 Drives: frs Location: nj Posts: 723 Thanks: 237 Thanked 347 Times in 232 Posts Mentioned: 58 Post(s) Tagged: 0 Thread(s)	@Kodename47 thank you mate for all the awesome tools and help

11-08-2014, 05:40 PM	#243
Toyota John Calle Atun Join Date: Sep 2013 Drives: 13 FRS, 93 Mr2, 85 ae86 Location: CT Posts: 158 Thanks: 12 Thanked 11 Times in 10 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Could anyone help me with removing the CL/OL delay in Romraider. Would like to confirm that I am changing the right tables to stop the LTFT for working.

12-12-2014, 08:19 AM	#244
steve99 Banned Join Date: Dec 2013 Drives: FT86 Location: Australia Posts: 7,998 Thanks: 1,035 Thanked 4,987 Times in 2,981 Posts Mentioned: 598 Post(s) Tagged: 2 Thread(s)	Added Grimspeed Intake MAF scaling to first post

12-12-2014, 09:40 AM	#246
yoruck Member Join Date: Jan 2012 Drives: ford fiesta st 150 Location: belgium Posts: 13 Thanks: 0 Thanked 1 Time in 1 Post Mentioned: 0 Post(s) Tagged: 0 Thread(s)	hi, just before a start trying to scal maf for my trd CAI perhaps somebody have already do it? i am interrested in

12-16-2014, 08:16 PM	#247
benlaz88 Senior Member Join Date: Sep 2013 Drives: 2013 Asphalt FRS Location: Tempe, Arizona Posts: 255 Thanks: 27 Thanked 44 Times in 34 Posts Mentioned: 3 Post(s) Tagged: 2 Thread(s)	Any AEM intake scaling yet?

12-18-2014, 04:05 PM	#249
rcampici Banned Join Date: Sep 2014 Drives: GTS86 Location: Australia Posts: 22 Thanks: 3 Thanked 0 Times in 0 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	With my OFT log I have Injection mode 2 and 3 This does not relate with the modes shown in this thread. I need to know please what the two modes in OFT are I am assuming 2 for CL and 3 for OL Further using Mafscaling Master there is a value dV/dT what value are people using for this? Thanks

User Name		Remember Me?
Password