01-12-2024, 08:55 PM | #19853 |
Senior Member
Join Date: Feb 2019
Drives: 2014 FR-S
Location: Long Beach
Posts: 108
Thanks: 32
Thanked 83 Times in 51 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
|
01-13-2024, 09:59 AM | #19854 |
Senior Member
Join Date: Apr 2020
Drives: 2018 BRZ
Location: Dayton, OH
Posts: 904
Thanks: 1,371
Thanked 768 Times in 435 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
My guess is that @dpfarr was referring to other cars that have the parking brake as part of the regular caliper (unlike the Twins that have a separate drum brake for the parking brake). In that case compressing the rear caliper requires a twisting motion, typically done with needle nose pliers (although there are dedicated tools for that as well).
|
01-13-2024, 10:38 AM | #19855 |
Barred
Join Date: Oct 2020
Drives: My18 wrxsti My19 brzts
Location: Botany Bay
Posts: 1,144
Thanks: 731
Thanked 1,187 Times in 610 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
You only need needle/long nosed pliers on a ts with good Brembo calipers. Calipers remain bolted on the car. 2 clips and 2 pins each brake caliper. Oh and a good squeeze with fingers on the pistons.
__________________
Wait until my Flex capacitor hits 88
|
01-13-2024, 10:42 AM | #19856 |
Senior Member
Join Date: May 2020
Drives: 22 BRZ limited
Location: Clarksville TN
Posts: 1,183
Thanks: 217
Thanked 990 Times in 521 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
Or Brembo style that come out the top after removing the clip and pin.
__________________
|
01-14-2024, 12:15 AM | #19857 |
Senior Member
Join Date: May 2020
Drives: BRZ ts
Location: SACRAMENTO
Posts: 752
Thanks: 411
Thanked 787 Times in 301 Posts
Mentioned: 8 Post(s)
Tagged: 1 Thread(s)
|
Yea, the process for brembos is new to me. 30k miles and about 3mm of pad left. Very reasonable to be able to swap track pads in while switching wheels.
|
01-17-2024, 08:41 PM | #19858 | |
Senior Member
Join Date: Aug 2020
Drives: 2017 BRZ PP, 2004 WRX
Location: Pittsburgh
Posts: 347
Thanks: 16
Thanked 249 Times in 157 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Depending on thickness differences between the two sets of pads, you do have to move the pistons back in and the fronts take a decent amount of force. You can do it with a pad and wiggle it back and forth, but it takes some effort... especially going from a thin pad to a full one. Pins take some effort in the front too. Best to pull them out from the rear rather than tapping from the front as you can scratch the caliper this way. The rears being much smaller are simple all around. ... so when you think about traditional sliding calipers, there isn't a ton of advantages actually. It's just about the same effort removing one bolt, swinging the caliper away, swapping pads and/or moving only two pistons vs four, and you're good. I've had both. They're not hard by any means, but not like half the time or anything.
__________________
2017 BRZ Limited Performance Pack - Steel Cities Region SCCA / North Hills Sports Car Club
|
|
The Following 2 Users Say Thank You to cmiovino For This Useful Post: | NoHaveMSG (01-18-2024), Ohio Enthusiast (01-17-2024) |
01-18-2024, 10:34 PM | #19859 | |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,167
Thanks: 18,158
Thanked 16,325 Times in 7,383 Posts
Mentioned: 107 Post(s)
Tagged: 0 Thread(s)
|
Quote:
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
|
The Following User Says Thank You to NoHaveMSG For This Useful Post: | Ultramaroon (01-18-2024) |
01-18-2024, 10:48 PM | #19860 |
義理チョコ
Join Date: Sep 2014
Drives: a 13 e8h frs
Location: vantucky, wa
Posts: 31,871
Thanks: 52,137
Thanked 36,521 Times in 18,922 Posts
Mentioned: 1107 Post(s)
Tagged: 9 Thread(s)
|
If it needs to be faster than a c-clamp, I need to examine my priorities.
__________________
|
01-20-2024, 01:02 AM | #19861 |
Senior Member
Join Date: May 2020
Drives: BRZ ts
Location: SACRAMENTO
Posts: 752
Thanks: 411
Thanked 787 Times in 301 Posts
Mentioned: 8 Post(s)
Tagged: 1 Thread(s)
|
I had a Jetta that needed a tool that simultaneously spread and rotated the piston.
|
The Following User Says Thank You to dpfarr For This Useful Post: | blsfrs (01-20-2024) |
01-20-2024, 09:57 AM | #19862 |
Senior Member
Join Date: Dec 2018
Drives: 2013 frs base
Location: central Virginia
Posts: 1,117
Thanks: 1,732
Thanked 918 Times in 476 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
I had a Passat with the same type calipers. I spent an hour trying to push and screw the piston in (the video said it would be easy) then got the loaner tool and finished each one in 3 minutes.
|
01-20-2024, 05:44 PM | #19863 |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,167
Thanks: 18,158
Thanked 16,325 Times in 7,383 Posts
Mentioned: 107 Post(s)
Tagged: 0 Thread(s)
|
My favorite tool for it is actually a clutch basket holder for a motorcycle.
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
01-20-2024, 07:04 PM | #19864 | |
義理チョコ
Join Date: Sep 2014
Drives: a 13 e8h frs
Location: vantucky, wa
Posts: 31,871
Thanks: 52,137
Thanked 36,521 Times in 18,922 Posts
Mentioned: 1107 Post(s)
Tagged: 9 Thread(s)
|
Quote:
I've been doing it wrong all these years.
__________________
|
|
The Following User Says Thank You to Ultramaroon For This Useful Post: | NoHaveMSG (01-20-2024) |
01-21-2024, 10:16 AM | #19865 |
Senior Member
Join Date: Dec 2018
Drives: 2013 frs base
Location: central Virginia
Posts: 1,117
Thanks: 1,732
Thanked 918 Times in 476 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
|
01-21-2024, 05:05 PM | #19866 |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,167
Thanks: 18,158
Thanked 16,325 Times in 7,383 Posts
Mentioned: 107 Post(s)
Tagged: 0 Thread(s)
|
Like this. Tons of leverage, quick to adjust.
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Saw My First FR-S Today | Marrk | Scion FR-S / Toyota 86 GT86 General Forum | 26 | 05-15-2013 12:40 PM |
Got my new FR-S today. | Boosted2.0 | Scion FR-S / Toyota 86 GT86 General Forum | 51 | 06-03-2012 10:35 PM |
Sat in a FRS today!! | Ladnerd | Scion FR-S / Toyota 86 GT86 General Forum | 12 | 04-30-2012 01:48 PM |
Got my VIN today... | Enemies | BRZ First-Gen (2012+) -- General Topics | 63 | 04-12-2012 10:19 PM |
sat in a BRZ today | NESW20 | BRZ First-Gen (2012+) -- General Topics | 8 | 03-31-2012 08:53 AM |