PTUNING 4-1 Full T304 SS Equal Length Double-Slip Race Header (200+whp 93 pump gas) - Page 23 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

yomny · 11-04-2014, 08:10 PM

Quote:

Originally Posted by juliog

Anyone knows the part numbers for the OEM gaskets?

This works SU00301111

s30series · 11-05-2014, 12:06 PM

Quote:

Originally Posted by juliog

Anyone knows the part numbers for the OEM gaskets?

Those are both the header gaskets as well as the header to overpipe gasket.

yomny · 11-05-2014, 01:28 PM

So the ptuning header doesn't come with a header-overpipe gasket?

s30series · 11-05-2014, 01:36 PM

Quote:

Originally Posted by yomny

So the ptuning header doesn't come with a header-overpipe gasket?

No it does not come with any gaskets.

The header-overpipe one is expensive too...im surprised the manifold-head gaskets are so cheap.

yomny · 11-05-2014, 01:43 PM

Quote:

Originally Posted by s30series

No it does not come with any gaskets.

The header-overpipe one is expensive too...im surprised the manifold-head gaskets are so cheap.

Thanks, does it come with any hardware? I'm assuming something to hold the over pipe since the Oem header has them studs.

rb6freak · 11-05-2014, 02:11 PM

Quote:

Originally Posted by yomny

Thanks, does it come with any hardware? I'm assuming something to hold the over pipe since the Oem header has them studs.

It does come with new hardware for the over pipe.

Gaskets are the optional at checkout according to their website. Gasket part numbers can be obtained by calling your local dealer.

phobos512 · 11-05-2014, 03:53 PM

Quote:

Originally Posted by juliog

Anyone knows the part numbers for the OEM gaskets?

http://www.trademotion.com/parts/201...agramCallOut=4

Header/Head Gasket - SU00301111
Header/Overpipe Gasket - SU00301110
Front Pipe / Mid-Pipe Gasket - SU00301112
Mid-Pipe / Axle-back Gasket - SU00301113

yomny · 11-05-2014, 08:34 PM

So these OEM crush gaskets, any specific way to install them? The nuts on the header to over pipe, any torque specs? The little nuts holding the runners together, do they come pre-tightened or should i give them a crush?

On a side note: This header is a work of art, feels solid and its beautiful. I love the vband modular setup

Solid flange right there

Calum · 11-05-2014, 08:53 PM

Quote:

Originally Posted by yomny

Wanna see a guy get frustrated? Show those flanges to @Dimman. Most of the header looks great, but that's a sealing face, finish the damn job!

Andrew025 · 11-05-2014, 09:20 PM

Quote:

Originally Posted by Calum

Wanna see a guy get frustrated? Show those flanges to @Dimman. Most of the header looks great, but that's a sealing face, finish the damn job!

Can you elaborate on that for someone who has no idea what that means?

FirestormFRS · 11-05-2014, 09:29 PM

Any third party dyno's out yet with a reasonable exhaust?

rb6freak · 11-05-2014, 10:30 PM

Quote:

Originally Posted by Calum

Wanna see a guy get frustrated? Show those flanges to @Dimman. Most of the header looks great, but that's a sealing face, finish the damn job!

The stock manifold has the same or similar finish to it.

Anh5oi · 11-05-2014, 11:56 PM

I wonder if this going to be 210 with ptuning header, Overpipe, test pipe and full exhaust with drop in filter..

Dimman · 11-06-2014, 12:17 AM

Quote:

Originally Posted by Calum

Wanna see a guy get frustrated? Show those flanges to @Dimman. Most of the header looks great, but that's a sealing face, finish the damn job!

I don't know, Calum. It looks like they're faced with a big end mill or flycutter. The way that light reflects on that in photos can make it look rougher than it is. And a bit of texture gives the gasket something to grip. More important that it's flat. Best way I think would be to heat cycle them after install and face them after to minimize/eliminate further heat stress related warping.

But I've kinda stopped caring about shitty parts anyways. (Desensitized from so many?)

I would give these guys a passing grade.

11-05-2014, 01:28 PM	#311
yomny Senior Member Join Date: Jul 2012 Drives: 2013 FRS Whiteout Location: MIA Posts: 1,545 Thanks: 557 Thanked 469 Times in 340 Posts Mentioned: 33 Post(s) Tagged: 5 Thread(s)	So the ptuning header doesn't come with a header-overpipe gasket? __________________ GTX2867R, moto-tuned , tomei op , motiv fp , Invidia Q300 ti , Rota titan 17x9 +42 , nt555 255/40 , ST coilovers w/cascam , Hotchkis sways

11-05-2014, 11:56 PM	#321
Anh5oi Member Join Date: Oct 2014 Drives: 13 FRS Location: Somewhere Posts: 76 Thanks: 1 Thanked 11 Times in 10 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	I wonder if this going to be 210 with ptuning header, Overpipe, test pipe and full exhaust with drop in filter.. __________________ Current: FRS(Daily), Cayenne(Weekend), 1000RR(Fun), 650Maxim(Fun). Recently Sold: 13 Boxster(Crash), 08&10 335i, 08 M3, 12 A4, 97 NSX....

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
WTB: Equal-length (EL) catted header	ck-GT86	Engine, Exhaust, Bolt-Ons	1	04-10-2014 07:31 PM
PRE Stepped diameter 4 to 1 double slip collector Header	Jmonty	Engine, Exhaust, Transmission	9	02-28-2014 09:24 AM
BRZ/FR-S/GT86 – 4-1 Equal Length Header Group Buy	P&L Motorsports	Groupbuys	634	12-03-2013 05:36 PM
PHASTEK DC Sports Equal Length Header	PhastekSport	Engine, Exhaust, Bolt-Ons	3	11-14-2013 10:17 PM

11-05-2014, 08:34 PM	#316
yomny Senior Member Join Date: Jul 2012 Drives: 2013 FRS Whiteout Location: MIA Posts: 1,545 Thanks: 557 Thanked 469 Times in 340 Posts Mentioned: 33 Post(s) Tagged: 5 Thread(s)	So these OEM crush gaskets, any specific way to install them? The nuts on the header to over pipe, any torque specs? The little nuts holding the runners together, do they come pre-tightened or should i give them a crush? On a side note: This header is a work of art, feels solid and its beautiful. I love the vband modular setup Solid flange right there

11-05-2014, 09:29 PM	#319
FirestormFRS Senior Member Join Date: Jul 2012 Drives: 2013 FR-S Location: Anytown Posts: 920 Thanks: 73 Thanked 643 Times in 302 Posts Mentioned: 3 Post(s) Tagged: 0 Thread(s)	Any third party dyno's out yet with a reasonable exhaust?

User Name		Remember Me?
Password