Nameless Performance Equal Length Stepped Header

[StormTrooper]

Originally Posted by mad_sb

#2 with no status change, Mine has to go out for coating too. I bet they ship as they complete them, but since they are building in stages they will all flow out the end of the assembly line very close to each other.

It's going to be interesting to see if Nameless posts the cam maps. I guess it depends on who is doing the tuning and what the arrangement is. Either way, i will certainly post my cam settings after I re-tune. If we had an eta on shipping I could go ahead and book dyno time.... but in all reality, I will install it the day it arrives and be at the dyno within a week.

Does your order status say awaiting pickup (aka invoice printed) or awaiting shipment (aka started to build)

I had thought the whole batch was being fabed up but mine says they haven't started building it yet.

Just curious, want to know which month I may get it.

[xjohnx]

Originally Posted by StormTrooper

Does your order status say awaiting pickup (aka invoice printed) or awaiting shipment (aka started to build)

I had thought the whole batch was being fabed up but mine says they haven't started building it yet.

Just curious, want to know which month I may get it.

Mine still says awaiting pickup and I was one of the first ones in. I wouldn't sweat it, they're likely not updating each order individually as these are being built as a batch.

[Ranatsu]

Originally Posted by StormTrooper

Does your order status say awaiting pickup (aka invoice printed) or awaiting shipment (aka started to build)

I had thought the whole batch was being fabed up but mine says they haven't started building it yet.

Just curious, want to know which month I may get it.

Mine says awaiting pickup. My order number is before Mad.

[StormTrooper]

Ahhh okas beginning to doubt if I made it in on the first batch and was actually the first one in the second... Lol

Anyone else planning on leaving the catback stock and just running the 2.5inch downpipe with the headers?

Doesn't seem to be an exhaust quiet enough to live with that's also lighter than stock lol

[xjohnx]

Originally Posted by StormTrooper

Anyone else planning on leaving the catback stock and just running the 2.5inch downpipe with the headers?

Doesn't seem to be an exhaust quiet enough to live with that's also lighter than stock lol

I've got the Nameless Overpipe/downpipe/high flow cat/helmholtz resonator installed (along with a Borla UEL header until my nameless arrives).

I am keeping the stock midpipe for now. Occasionally I'll switch from the nameless axleback to the stock axleback, depending on my mood. Stock catback makes it plenty quiet, IMO.

[FrsDuke]

Originally Posted by StormTrooper

Ahhh okas beginning to doubt if I made it in on the first batch and was actually the first one in the second... Lol

Anyone else planning on leaving the catback stock and just running the 2.5inch downpipe with the headers?

Doesn't seem to be an exhaust quiet enough to live with that's also lighter than stock lol

Probably. I have a track pipe with tip I will try first as it's the only exhaust piece I have currently, but I expect it to be too insane. Still have my stock axleback in the garage. Eventually getting fp/op but probably after new final drive.

[mad_sb]

I'm doing Nameless Header > Nameless catted helmholtz 2.5 > Invidia Q300

I still have my single exit varex setup for when I am ready retire the FRS from daily driver duty, but for now the Q300 stays on. Currently running Fa20 catted long tube > Nameless catted helmholtz 2.5 > Invidia Q300

ohh and my order status has not changed.. I expect they will flip the bits on the order status as they box them up to ship out. So we will probably all get notified aroudn the same time. I hope the ones getting coated are the first ones completed

[Ranatsu]

Originally Posted by mad_sb

I'm doing Nameless Header > Nameless catted helmholtz 2.5 > Invidia Q300

I still have my single exit varex setup for when I am ready retire the FRS from daily driver duty, but for now the Q300 stays on. Currently running Fa20 catted long tube > Nameless catted helmholtz 2.5 > Invidia Q300

ohh and my order status has not changed.. I expect they will flip the bits on the order status as they box them up to ship out. So we will probably all get notified aroudn the same time. I hope the ones getting coated are the first ones completed

My setup will be similar except I have the SRT catback.

[frslee]

When was the expected ship out date?

[Ranatsu]

Originally Posted by frslee

When was the expected ship out date?

"soon"

[pheoxs]

@Ryan@Nameless

Have you guys released any numbers/dynos for full nameless exhaust with the innovate setup as of yet? I believe you guys had tested those two together a bunch?

[xjohnx]

Maybe we'll get another batch of update photos and timelines from @Ryan@Nameless or @Jason@Nameless

[Assunta]

Originally Posted by xjohnx

Maybe we'll get another batch of update photos and timelines from @Ryan@Nameless or @Jason@Nameless

I'm also very interested.

[rgt]

Originally Posted by OrbitalEllipses

Let me have some of what this guy's smoking!







So what do you want to see?

1. stock car baseline - no tune
   
2. stock car baseline - tuned
   
3. same car as above - no tune with THIS header
   
4. same car as above - tune for stock header except running THIS header
   
5. same car as above - tuned for THIS header
   

I thought I was going crazy when you replied that there wasn't any data that showed just a header with no tune made measurable power. Went back and searched and found this:

http://www.ft86club.com/forums/showthread.php?t=52835