JDL 4-2-1 EL header

[Breadman]

shit its not even really close. i guess its the same on e85 too

[CSG Mike]

Originally Posted by JBezugs

Very illuminating, thanks for sharing Mike! Looks like the JDL can keep up with the A350 in the dip zone, at least from 3400 to 4000 rpm, but above that, the A350 is still the king of the hill until you hit the top end.

The ACE is an amazing product without a doubt, but for the price to my door in Canada, I’m still happy with the JDL from a bang-for-buck perspective.

The dip that particular Ace graph is an anomaly. See the graphs under for how they normally look. Not sure why the dip is there on that pull; may have been wheel slip on the dyno or something.

[408brz]

I just finished with install of JDL 4-2-1 (black ceramic) and ACE overpipe, both from CSG (thank you!), on a 2013 BRZ. Paired with stock front pipe and milltek resonated sport catback. Tuned by Delicious (fun meeting/talking with Bill) at Mann Engineering (always gracious hosts).

I had no fitment issues, no locations where the header is making contact. Feels and sounds great.

[Summerwolf]

@CSG Mike


These are the same results posted in the other thread of a JDL 4-1 header correct? NOT the 4-2-1.

[MilkyWitness]

asdf

[408brz]

Yes, stock before.

[justint5387]

Useless comparison and misinformation.

Trying to sell parts?

[weederr33]

I know it's an outdated and discontinued header, but I'm considering swapping my Nameless Performance/ Cosworth headers for these sometime early next year. Any idea how this could compare to it?

[churchx]

Why would you? Nameless/Cossworth's also is very good header performing very good. Some drawbacks might be it not filling well torque dip and bad clearance in front of engine, but it did well regarding overall gains/area under curve. Imho there is very little to gain switching one catless header to another, bad price/performancy wise purchase decision.

[weederr33]

Originally Posted by churchx

Why would you? Nameless/Cossworth's also is very good header performing very good. Some drawbacks might be it not filling well torque dip and bad clearance in front of engine, but it did well regarding overall gains/area under curve. Imho there is very little to gain switching one catless header to another, bad price/performancy wise purchase decision.

It's just a thought is all.

[Turdinator]

I installed my 4-2-1 about a week ago. They went it very smoothly. There was no interference anywhere. In fact the 4-2-1 fit better than the JDL UEL header they replaced. Power wise they have a smoother torque cure than the UEL but I shouldn't really comment as I am just on the Delicious base map. Once the tune is finalised I'll have some better driving feel comparisons.

[Turdinator]

Originally Posted by weederr33

I know it's an outdated and discontinued header, but I'm considering swapping my Nameless Performance/ Cosworth headers for these sometime early next year. Any idea how this could compare to it?

I doubt anyone will really be able to compare. If you want to update then see how much you can sell the Nameless headers for to offset the cost of the new headers and tune. Also keep in mind the Nameless headers have a 3" output while the JDLs have a 2.5" so you may need to change your over pipe setup to suit.

[weederr33]

Originally Posted by Turdinator

I doubt anyone will really be able to compare. If you want to update then see how much you can sell the Nameless headers for to offset the cost of the new headers and tune. Also keep in mind the Nameless headers have a 3" output while the JDLs have a 2.5" so you may need to change your over pipe setup to suit.

I have a 2.5" overpipe so that will stay.

[MilkyWitness]

asdf