exhaust hangers - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

jazztennor · 02-18-2013, 02:20 AM

hey everyone i have changed my exhaust to the evo3 greddy and damn there nice but i need to change the rubber parts on the hangers. Do do you guys recommend??? anything special??

whataboutbob · 02-18-2013, 02:33 AM

I replaced mine with some Perrin ones http://www.perrinperformance.com/p/2152. I'm running an Invidia N1 and Invidia front pipe with the high flow cat.

Sportsguy83 · 02-18-2013, 02:35 AM

Quote:

Originally Posted by jazztennor

hey everyone i have changed my exhaust to the evo3 greddy and damn there nice but i need to change the rubber parts on the hangers. Do do you guys recommend??? anything special??

Why you need to replace the stock hangers? They can't be seen unless you go under the car and they do the job since they are so new (unless you broke some

)

Nameless, Perrin, they are all very similar if not the same.

Z3D · 02-18-2013, 03:23 AM

Taking the stock hangers off can sometimes be a pain. The rubber is sometimes very tight and grabby on the metal hangers. A pro tip is to use an aerosol lubricant like WD40 to aid the rubber hanger mounts coming on and off. Makes life just a bit easier.

sw20kosh · 02-18-2013, 04:32 AM

A pro tip is to buy the clamps that are designed specifically to remove rubber hangers.

jazztennor · 02-18-2013, 12:44 PM

Quote:

Originally Posted by Sportsguy83

Why you need to replace the stock hangers? They can't be seen unless you go under the car and they do the job since they are so new (unless you broke some

)

Nameless, Perrin, they are all very similar if not the same.

My exhaust sites funny one side. Next time we are together i will show you one side is lower than the other. So i went under the other day to look. Out of the 4 rubber hangers 3 look perfect but the 4th is not hanging normal. It looks like it has been squished in and it wont move back to a normal stretched position.

jflogerzi · 02-18-2013, 01:48 PM

Quote:

Originally Posted by Z3D

Taking the stock hangers off can sometimes be a pain. The rubber is sometimes very tight and grabby on the metal hangers. A pro tip is to use an aerosol lubricant like WD40 to aid the rubber hanger mounts coming on and off. Makes life just a bit easier.

Yup I did this. Also working them in a left to right motion for a bit first will also help make your life easier getting the stock hangers off.

King Tut · 02-19-2013, 10:57 AM

Quote:

Originally Posted by jazztennor

My exhaust sites funny one side. Next time we are together i will show you one side is lower than the other. So i went under the other day to look. Out of the 4 rubber hangers 3 look perfect but the 4th is not hanging normal. It looks like it has been squished in and it wont move back to a normal stretched position.

That sounds like install error. I would loosen everything back up until all the hangers are in a non binded position and then tighten things back up.

02-18-2013, 02:20 AM	#1
jazztennor Senior Member Join Date: Aug 2012 Drives: Scion FR-s Location: Concord NC Posts: 422 Thanks: 41 Thanked 109 Times in 70 Posts Mentioned: 29 Post(s) Tagged: 2 Thread(s)	exhaust hangers hey everyone i have changed my exhaust to the evo3 greddy and damn there nice but i need to change the rubber parts on the hangers. Do do you guys recommend??? anything special?? __________________ Upgrades EVO 3 Exhaust,Emblem swap,Full Carbon Interior,Greddy intake

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Exhaust System/Exhaust Manifold Removal and Replacement	GrimmSpeed	DIY (Do-It-Yourself) Guides	52	11-11-2015 10:30 PM
Perrin Catback Exhaust vs Nameless Performance Exhaust.	vignesh	Engine, Exhaust, Transmission	201	06-05-2013 10:47 PM
Exhaust hangers	yomchi1989	AUSTRALIA	4	12-01-2012 02:15 AM
Rusty exhaust hangers?	finch1750	Issues \| Warranty \| Recalls / TSB	5	11-12-2012 01:29 AM
Can someone explain the diffrence between catback exhaust and axleback exhaust?	speedy racer	Engine, Exhaust, Transmission	12	09-23-2012 01:24 PM

02-18-2013, 03:23 AM	#4
Z3D Member Join Date: Jan 2013 Drives: BRZ Location: Massachusetts Posts: 89 Thanks: 38 Thanked 20 Times in 13 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Taking the stock hangers off can sometimes be a pain. The rubber is sometimes very tight and grabby on the metal hangers. A pro tip is to use an aerosol lubricant like WD40 to aid the rubber hanger mounts coming on and off. Makes life just a bit easier.

02-18-2013, 04:32 AM	#5
sw20kosh Senior Member Join Date: Jul 2012 Drives: 2013 Black FR-S Location: SF Posts: 3,030 Thanks: 881 Thanked 2,014 Times in 990 Posts Mentioned: 153 Post(s) Tagged: 1 Thread(s)	A pro tip is to buy the clamps that are designed specifically to remove rubber hangers.

User Name		Remember Me?
Password