PERRIN MOTOR MOUNTS FR-S & BRZ Just arrived PICTURES - Page 3 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

SpeedmasterBRZ · 01-14-2013, 05:29 PM

Wait for Group N for DD.

gmookher · 01-14-2013, 07:23 PM

have you ever owned poly mounts?

its not a big deal at all

done commonly and often, using this kind of bushing with interlocking internals

I DD my other urethane mounts, no issue at all, no extra NVH, except at startup, while cranking, its a bit more palpable thru the frame

most cars doing mounts already have a lil extra NVH from exhausts and such, so the fractional incremental amount of extra or added NVH is truly negligible.

perhaps if you were adding these mounts to a bone stock car, with bone stock exh, you may better be able to find those key differences

Celica00 · 01-14-2013, 07:44 PM

polyurethane is sex for cars.

OrbitalEllipses · 01-14-2013, 07:51 PM

Quote:

Originally Posted by SpeedmasterBRZ

Wait for Group N for DD.

Is there a Group N BRZ? No there isn't. There won't be Group N mounts because they needed to produce those for PWRC homologation as far as I understand. There's no homologated BRZ race car in the WRC as Subaru isn't in the WRC...and now we're talking in circles.

SpeedmasterBRZ · 01-14-2013, 08:05 PM

Google Isle of man BRZ.

IF there is profit to be had people will make a part to sell.

STi/SPT are making parts for it and it is not a "rally" car.

OrbitalEllipses · 01-14-2013, 08:12 PM

Quote:

Originally Posted by SpeedmasterBRZ

Google Isle of man BRZ.

IF there is profit to be had people will make a part to sell.

STi/SPT are making parts for it and it is not a "rally" car.

The BRZ is NOT in ANY homologated series right now. Group-N is related to FIA's WRC. Subaru is NOT in WRC. Subaru will NOT produce so called "Group-N" bits for the BRZ. SPT has NOTHING to do with anything at all. SPT does not make bushings or parts even.

Pete · 01-14-2013, 08:21 PM

I just ordered a set of these with a rear shifter bushing and some other swag. Can't wait to get this kit in my car.

PERRIN_Jeff · 01-15-2013, 08:41 PM

Quote:

Originally Posted by Racecomp Engineering

This question is directed to Jeff:

With Group-N mounts on a WRX or STI, most notice after a few hundred miles that the mounts "break in" and the vibration at idle is NO where near as bad as it was initially. My question is.....do you think this ENERGY bushing you use, ..will "break in" and mellow out some of the initial vibration?

Myles Williams
RCE
ps: Love my exhaust on the BRZ.

It does seem to mellow out, but it still has some vibrations. I really don't find it that annoying on this engine compared to the EJ engine with these mounts. I think the engine is much smoother and there are less things that rattle in the BRZ compared to the STI!

I daily drove the STI this way for 2 years and it wasn't that bad. But its all relative to what you like. After driving the BRZ with them for a while, I think that people will find them very appealing in the BRZ because it really makes the drivetrain solid and even more responsive.

Oh and yes, they will feel the same in an FR-S

Racecomp Engineering · 01-16-2013, 04:27 AM

Quote:

Originally Posted by PERRIN_Jeff

It does seem to mellow out, but it still has some vibrations. I really don't find it that annoying on this engine compared to the EJ engine with these mounts. I think the engine is much smoother and there are less things that rattle in the BRZ compared to the STI!

I daily drove the STI this way for 2 years and it wasn't that bad. But its all relative to what you like. After driving the BRZ with them for a while, I think that people will find them very appealing in the BRZ because it really makes the drivetrain solid and even more responsive.

Oh and yes, they will feel the same in an FR-S

Thank you sir !

Just waiting for Oil cooler and header !

Myles

Pete · 01-16-2013, 10:02 AM

Quote:

Originally Posted by Racecomp Engineering

Thank you sir !

Just waiting for Oil cooler and header !

Myles

Those are my next planned mods. Really looking forward to the header....hint hint jeff.

Frostyman · 01-16-2013, 11:23 AM

I love Perrin stuff, but OMG the back orders... I guess everyone else loves Perrin products too.

milenko11 · 01-16-2013, 03:48 PM

Does this help with the shifter vibrating?

OrbitalEllipses · 01-16-2013, 04:33 PM

Quote:

Originally Posted by milenko11

Does this help with the shifter vibrating?

Would likely only make it worse since engine and tranny are more directly connected.

illmatic · 01-17-2013, 01:35 PM

Quote:

Originally Posted by OrbitalEllipses

Is there a Group N BRZ? No there isn't. There won't be Group N mounts because they needed to produce those for PWRC homologation as far as I understand. There's no homologated BRZ race car in the WRC as Subaru isn't in the WRC...and now we're talking in circles.

I'm sure one of the new Subaru models(Impreza, WRX, or STi) with the FAXX DIT will be homologated and there will be some interchangeability in Group N parts.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Whiteline Com-c top mounts	sw20kosh	Suspension \| Chassis \| Brakes -- Sponsored by 949 Racing	349	05-27-2015 06:15 AM
upgraded mounts?	7thgear	Engine, Exhaust, Transmission	19	01-12-2013 12:31 AM
Buyer Beware: Motor Mounts	cobrabyte	Engine, Exhaust, Transmission	5	01-04-2013 09:14 PM
Autocross Camera Mounts?	fritzy	BRZ First-Gen (2012+) — General Topics	7	08-03-2012 11:48 PM
Dash Mounts for gadgets	smbrm	Cosmetic Modification (Interior/Exterior/Lighting)	0	06-28-2012 08:07 PM

01-14-2013, 05:29 PM	#29
SpeedmasterBRZ Banned Join Date: Aug 2012 Drives: Pearl BRZ Limited Location: Utah Posts: 61 Thanks: 21 Thanked 20 Times in 16 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Wait for Group N for DD.

01-14-2013, 07:23 PM	#30
gmookher Banned Join Date: Aug 2012 Drives: VortechSC,BorlaEL,Perrin,GCRace Location: HighHeatHighAltitudeAZ,USA Posts: 2,254 Thanks: 458 Thanked 669 Times in 394 Posts Mentioned: 9 Post(s) Tagged: 2 Thread(s)	have you ever owned poly mounts? its not a big deal at all done commonly and often, using this kind of bushing with interlocking internals I DD my other urethane mounts, no issue at all, no extra NVH, except at startup, while cranking, its a bit more palpable thru the frame most cars doing mounts already have a lil extra NVH from exhausts and such, so the fractional incremental amount of extra or added NVH is truly negligible. perhaps if you were adding these mounts to a bone stock car, with bone stock exh, you may better be able to find those key differences

01-14-2013, 07:44 PM	#31
Celica00 Senior Member Join Date: Sep 2012 Drives: 86 Location: utah Posts: 1,156 Thanks: 842 Thanked 798 Times in 434 Posts Mentioned: 8 Post(s) Tagged: 2 Thread(s)	polyurethane is sex for cars.

01-14-2013, 08:05 PM	#33
SpeedmasterBRZ Banned Join Date: Aug 2012 Drives: Pearl BRZ Limited Location: Utah Posts: 61 Thanks: 21 Thanked 20 Times in 16 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Google Isle of man BRZ. IF there is profit to be had people will make a part to sell. STi/SPT are making parts for it and it is not a "rally" car.

01-14-2013, 08:21 PM	#35
Pete Senior Member Join Date: Aug 2012 Drives: 22 BRZ Location: Houston, TX Posts: 615 Thanks: 1,341 Thanked 478 Times in 230 Posts Mentioned: 15 Post(s) Tagged: 0 Thread(s)	I just ordered a set of these with a rear shifter bushing and some other swag. Can't wait to get this kit in my car.

01-16-2013, 11:23 AM	#39
Frostyman Senior Member Join Date: Oct 2012 Drives: 2013 Raven FRS Location: Virginia Beach, Va Posts: 496 Thanks: 30 Thanked 143 Times in 93 Posts Mentioned: 18 Post(s) Tagged: 3 Thread(s)	I love Perrin stuff, but OMG the back orders... I guess everyone else loves Perrin products too.

01-16-2013, 03:48 PM	#40
milenko11 Member Join Date: Feb 2012 Drives: no Location: internet Posts: 85 Thanks: 5 Thanked 6 Times in 6 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Does this help with the shifter vibrating?

User Name		Remember Me?
Password