05-03-2016, 12:54 AM | #1 |
Junior Member
Join Date: Feb 2015
Drives: 2015 Scion FRS RS 1.0
Location: St.Paul MN
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
P0031
So I just installed my tomei UEL headers,over pipe and tanabe front pipe. after the installation the CEL came out right away so I decided to buy the OFT to tune my car and to get rid of the CEL. Now my problem is the CEL is still there after tuning it with the stage 2 UEL 93oct. the code is P0031. How will I get rid of the CEL?Help please.
|
05-03-2016, 01:23 AM | #2 |
Senior Member
Join Date: Apr 2014
Drives: Toyota 86 GTS
Location: Australia
Posts: 1,129
Thanks: 453
Thanked 895 Times in 424 Posts
Mentioned: 211 Post(s)
Tagged: 0 Thread(s)
|
You installed some hardware which resulted in a hardware fault, which you decided to solve with software.
Go fix and/or replace your oxygen sensor which you damaged or plugged in reverse (dunno how that would even be possible).
__________________
Last edited by Wayno; 05-03-2016 at 01:47 AM. |
The Following User Says Thank You to Wayno For This Useful Post: | guybo (02-09-2018) |
05-03-2016, 05:26 AM | #3 |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,988 Times in 2,982 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
google this "P0031 subaru"
as above its likely stuffed front 02 sensor the code you get with catless header is P0420 cat efficiency this is disabled in oft stage2 tunes. the tune is fine your have an o2 sensor issue to fix read the Basic Bolt on Mods guide link below in pretty colours its got some tips in it to reduce your chances of stuffing the next sensor, ie run a thread tap through o2 sensor bungs in header so you dont need to force them in. you might have also blown the "efi htr" fuse see here if the wiring is damaged or the o2 heater went short circuit http://www.ft86club.com/forums/showt...92#post2205392 |
05-03-2016, 11:52 AM | #4 |
Junior Member
Join Date: Feb 2015
Drives: 2015 Scion FRS RS 1.0
Location: St.Paul MN
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
thanks mate! i'll check it now and hope I can fix it
|
02-09-2018, 12:56 AM | #5 |
Member
Join Date: Feb 2018
Drives: 2017 GT86
Location: halifax
Posts: 12
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
|
11-18-2022, 10:44 PM | #6 | |
Junior Member
Join Date: Nov 2022
Drives: brz '16, elise s3 '15, mb c250 '14
Location: AD
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Got the same, UEL was installed by a garage. |
|
11-18-2022, 10:54 PM | #7 |
ProCrastinationConsultant
Join Date: Sep 2013
Drives: '14 Ranger, '18 Tacoma 4Dr LB
Location: chicago-ish
Posts: 11,330
Thanks: 35,240
Thanked 13,675 Times in 6,782 Posts
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
|
did you follow the steps in post #3?
__________________
"The time you enjoy wasting is not wasted time"
|
|
|
Tags |
cel, headers, o2 sensor, oft.vishnu.tune.tunning |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
P0134 and P0030->P0031 | Howardwei | Software Tuning | 7 | 12-08-2013 02:39 PM |