Oil Fill Cap Broke - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

congee · 10-09-2022, 02:20 PM

Hello,

While changing my oil today on my 2013 brz. The stock oem plastic oil fill cap snapped and a piece the size of a finger nail broke into the fill hole. Any suggestions and anyone know how bad this will effect the engine??

Thanks

Ultramaroon · 10-09-2022, 03:33 PM

Tough call. Would be captured by the pickup screen but might hang up in the pickup tube itself. If it doesn't come out draining the oil, drop the pan and remove it to be safe.

soundman98 · 10-09-2022, 04:19 PM

Quote:

Originally Posted by Ultramaroon

Tough call. Would be captured by the pickup screen but might hang up in the pickup tube itself. If it doesn't come out draining the oil, drop the pan and remove it to be safe.

but then the fill opening is above one of the cam shafts. do the cams drain directly into the lower pan?

Ultramaroon · 10-09-2022, 07:31 PM

Quote:

Originally Posted by soundman98

but then the fill opening is above one of the cam shafts. do the cams drain directly into the lower pan?

They do. That's the main reason for all the shit in the screens from the j02 recall. I could see it being chewed up on the way down, but

soundman98 · 10-10-2022, 01:38 AM

i'm really more curious how a hand-tightened plastic cap on a machined aluminum surface cracked enough to fall apart...

DarkPira7e · 10-10-2022, 02:44 AM

Quote:

Originally Posted by soundman98

i'm really more curious how a hand-tightened plastic cap on a machined aluminum surface cracked enough to fall apart...

I'm betting it was over tightened and they used vice grips or something to get a hold on it

22R · 10-10-2022, 06:05 AM

Quote:

Originally Posted by DarkPira7e

I'm betting it was over tightened and they used vice grips or something to get a hold on it

Lawd !!

22R

Breadman · 10-10-2022, 10:44 AM

Quote:

Originally Posted by soundman98

i'm really more curious how a hand-tightened plastic cap on a machined aluminum surface cracked enough to fall apart...

Probably crossthreaded it and magilla gorillaed it in

Sapphireho · 10-10-2022, 11:26 AM

Very strange. Impossible to cross thread. It's like a Playskool motor skill, eye-hand coordination toy. Need the full story.

congee · 10-10-2022, 05:40 PM

The cap was too tight so I used pliers to clamp the insides of the handle(where theres a U shaped space on each end)and after getting it off. Rested it on the opening and didn’t know one end was cracked so once i lifted it up, the piece fell right in…. Rookie mistake.

Sadly, drained the oil and nothing came out but ive driven it for around 100kms and no issues so far. Will probably change the oil again in a few days just to be safe until my mechanic is free to pull the oil pan. He did say there shouldn’t be too big of a problem bit better safe than sorry

Ultramaroon · 10-10-2022, 06:29 PM

Quote:

Originally Posted by congee

The cap was too tight so I used pliers to clamp the insides of the handle(where theres a U shaped space on each end)and after getting it off. Rested it on the opening and didn’t know one end was cracked so once i lifted it up, the piece fell right in…. Rookie mistake.

Sadly, drained the oil and nothing came out but ive driven it for around 100kms and no issues so far. Will probably change the oil again in a few days just to be safe until my mechanic is free to pull the oil pan. He did say there shouldn’t be too big of a problem bit better safe than sorry

Consider the size of the drain. When you say "fingernail," I wonder if the fragment is too big to come out the drain. Either that, or it's just laying in the bottom of the pan, minding its own business.

congee · 10-10-2022, 07:46 PM

Quote:

Originally Posted by Ultramaroon

Consider the size of the drain. When you say "fingernail," I wonder if the fragment is too big to come out the drain. Either that, or it's just laying in the bottom of the pan, minding its own business.

Hoping its just sitting at the bottom of the pan or lodge into something but it should fit through the drain hole. i suspect it’s probably somewhere in the oil fill area since theres a bunch of random gears/mechanical parts near the opening. Probably trapped inbetween something. My biggest fear is that it breaks down into smaller pieces or melts and then somehow gets through the pick up screen and filter. Going to put in new oil again and then again in a month or so just to be safe.

Ultramaroon · 10-11-2022, 12:01 AM

Quote:

Originally Posted by congee

Going to put in new oil again and then again in a month or so just to be safe.

Meh.... Don't waste good oil.

Sapphireho · 10-11-2022, 08:02 AM

So to clarify size, it is this piece?

10-09-2022, 02:20 PM	#1
congee Senior Member Join Date: Jul 2013 Drives: SSM BRZ Location: Canada Posts: 545 Thanks: 218 Thanked 150 Times in 86 Posts Mentioned: 8 Post(s) Tagged: 0 Thread(s)	Oil Fill Cap Broke Hello, While changing my oil today on my 2013 brz. The stock oem plastic oil fill cap snapped and a piece the size of a finger nail broke into the fill hole. Any suggestions and anyone know how bad this will effect the engine?? Thanks __________________

10-09-2022, 03:33 PM	#2
Ultramaroon not playing cards Join Date: Sep 2014 Drives: a 13 e8h frs Location: vantucky, wa Posts: 32,396 Thanks: 53,053 Thanked 37,225 Times in 19,308 Posts Mentioned: 1117 Post(s) Tagged: 9 Thread(s)	Tough call. Would be captured by the pickup screen but might hang up in the pickup tube itself. If it doesn't come out draining the oil, drop the pan and remove it to be safe. __________________ service manuals

10-10-2022, 01:38 AM	#5
soundman98 ProCrastinationConsultant Join Date: Sep 2013 Drives: '14 Ranger, '18 Tacoma 4Dr LB Location: chicago-ish Posts: 11,330 Thanks: 35,240 Thanked 13,675 Times in 6,782 Posts Mentioned: 98 Post(s) Tagged: 0 Thread(s)	i'm really more curious how a hand-tightened plastic cap on a machined aluminum surface cracked enough to fall apart... __________________ "The time you enjoy wasting is not wasted time"

10-10-2022, 11:26 AM	#9
Sapphireho Famous Potatoes Join Date: Mar 2016 Drives: '15 ultramarine Location: Idaho Posts: 14,000 Thanks: 5,796 Thanked 19,557 Times in 9,206 Posts Mentioned: 162 Post(s) Tagged: 0 Thread(s)	Very strange. Impossible to cross thread. It's like a Playskool motor skill, eye-hand coordination toy. Need the full story. Attached Images

10-10-2022, 05:40 PM	#10
congee Senior Member Join Date: Jul 2013 Drives: SSM BRZ Location: Canada Posts: 545 Thanks: 218 Thanked 150 Times in 86 Posts Mentioned: 8 Post(s) Tagged: 0 Thread(s)	The cap was too tight so I used pliers to clamp the insides of the handle(where theres a U shaped space on each end)and after getting it off. Rested it on the opening and didn’t know one end was cracked so once i lifted it up, the piece fell right in…. Rookie mistake. Sadly, drained the oil and nothing came out but ive driven it for around 100kms and no issues so far. Will probably change the oil again in a few days just to be safe until my mechanic is free to pull the oil pan. He did say there shouldn’t be too big of a problem bit better safe than sorry __________________

10-11-2022, 08:02 AM	#14
Sapphireho Famous Potatoes Join Date: Mar 2016 Drives: '15 ultramarine Location: Idaho Posts: 14,000 Thanks: 5,796 Thanked 19,557 Times in 9,206 Posts Mentioned: 162 Post(s) Tagged: 0 Thread(s)	So to clarify size, it is this piece? Attached Images

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Rocker arm broke and broke my valve cover...	j0hnnykthx	Issues \| Warranty \| Recalls / TSB	9	08-07-2020 09:12 AM
Over fill oil	Halo_2	Issues \| Warranty \| Recalls / TSB	14	07-18-2020 10:18 AM
Is it necessary to pre-fill the oil filter?	lupindub	Mechanical Maintenance (Oil, Fluids, Break-In, Servicing)	27	06-07-2016 04:58 PM
Fill and paint? or PDR...	rhythmM	Cosmetic Maintenance (Wash, Wax, Detailing, Body Repairs)	3	02-12-2014 10:36 PM
First fill-up...	mit_peid	Scion FR-S / Toyota 86 GT86 General Forum	3	01-20-2013 06:46 PM

User Name		Remember Me?
Password