|
Tracking / Autocross / HPDE / Drifting What these cars were built for! |
|
Thread Tools | Search this Thread |
08-14-2022, 09:18 AM | #15 | |
Senior Member
Join Date: May 2012
Drives: 2013 Series 10 6MT FR-S
Location: Moreno Valley, CA
Posts: 5,560
Thanks: 2,010
Thanked 2,033 Times in 1,470 Posts
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Sent from my Pixel 6 using Tapatalk
__________________
2013 Series 10 FRS #553
RCE T2's, SPC LCAs -4/2.6 camber JDL 4-2-1 EL, FP and OP, Tuned by Zach@CSG on e85 RR Wilwood Front/Rear Sport BBK, Motul 600 Fluid ARC-8 17x9 SX2 GTs 245s/Koing 17x8 v730's 225's |
|
08-14-2022, 10:28 AM | #16 | |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,265
Thanks: 18,364
Thanked 16,460 Times in 7,451 Posts
Mentioned: 109 Post(s)
Tagged: 0 Thread(s)
|
Quote:
The mounting on the two piece Verus unit isn’t that good. I built a bracket for mine that bolts to the lower rad support and it’s much stouter. I’ve still broken it twice and it always seems to get warped, it’s getting tossed for a homemade splitter this winter.
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
|
The Following User Says Thank You to NoHaveMSG For This Useful Post: | DocWalt (08-17-2022) |
08-14-2022, 01:53 PM | #17 | |
Senior Member
Join Date: May 2012
Drives: 2013 Series 10 6MT FR-S
Location: Moreno Valley, CA
Posts: 5,560
Thanks: 2,010
Thanked 2,033 Times in 1,470 Posts
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Sent from my Pixel 6 using Tapatalk
__________________
2013 Series 10 FRS #553
RCE T2's, SPC LCAs -4/2.6 camber JDL 4-2-1 EL, FP and OP, Tuned by Zach@CSG on e85 RR Wilwood Front/Rear Sport BBK, Motul 600 Fluid ARC-8 17x9 SX2 GTs 245s/Koing 17x8 v730's 225's |
|
08-14-2022, 01:57 PM | #18 |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,265
Thanks: 18,364
Thanked 16,460 Times in 7,451 Posts
Mentioned: 109 Post(s)
Tagged: 0 Thread(s)
|
Yes. There is not enough support at the rear is the main issue I see so it hinges on the splitter rods. I also made a plate that mounts the halves together more solidly. In the end, with the amount of wing I have it isn't enough splitter anyway.
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
The Following User Says Thank You to NoHaveMSG For This Useful Post: | jflogerzi (08-14-2022) |
08-14-2022, 04:43 PM | #19 | |
Senior Member
Join Date: May 2012
Drives: 2013 Series 10 6MT FR-S
Location: Moreno Valley, CA
Posts: 5,560
Thanks: 2,010
Thanked 2,033 Times in 1,470 Posts
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Sent from my Pixel 6 using Tapatalk
__________________
2013 Series 10 FRS #553
RCE T2's, SPC LCAs -4/2.6 camber JDL 4-2-1 EL, FP and OP, Tuned by Zach@CSG on e85 RR Wilwood Front/Rear Sport BBK, Motul 600 Fluid ARC-8 17x9 SX2 GTs 245s/Koing 17x8 v730's 225's |
|
08-14-2022, 04:47 PM | #20 |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,265
Thanks: 18,364
Thanked 16,460 Times in 7,451 Posts
Mentioned: 109 Post(s)
Tagged: 0 Thread(s)
|
It's pretty much the whole back edge needs better support. Mounting to the bumper cover isn't that solid and the rear mounts that go under towards the back just are not enough to handle an off into the grass or a light curb strike. I supported it with a bracket about 8" across in the middle and mounted the splitter to that support and that support to the lower rad mount.
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
08-14-2022, 05:04 PM | #21 | |
Senior Member
Join Date: May 2012
Drives: 2013 Series 10 6MT FR-S
Location: Moreno Valley, CA
Posts: 5,560
Thanks: 2,010
Thanked 2,033 Times in 1,470 Posts
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
|
Quote:
__________________
2013 Series 10 FRS #553
RCE T2's, SPC LCAs -4/2.6 camber JDL 4-2-1 EL, FP and OP, Tuned by Zach@CSG on e85 RR Wilwood Front/Rear Sport BBK, Motul 600 Fluid ARC-8 17x9 SX2 GTs 245s/Koing 17x8 v730's 225's |
|
08-14-2022, 05:55 PM | #22 |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,265
Thanks: 18,364
Thanked 16,460 Times in 7,451 Posts
Mentioned: 109 Post(s)
Tagged: 0 Thread(s)
|
I will try to.
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
The Following User Says Thank You to NoHaveMSG For This Useful Post: | norcalpb (08-14-2022) |
08-14-2022, 06:10 PM | #23 |
Senior Member
Join Date: Dec 2018
Drives: 2013 frs base
Location: central Virginia
Posts: 1,236
Thanks: 2,002
Thanked 1,153 Times in 557 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
For my side splitters (2.0), I used 1/4" composite aluminum that I bought directly from Falken Design. There prices were good and their shipping was fast. Good source of material for the DIY crowd.
|
08-14-2022, 06:38 PM | #24 |
Senior Member
Join Date: May 2020
Drives: 22 BRZ limited
Location: Clarksville TN
Posts: 1,198
Thanks: 219
Thanked 1,004 Times in 530 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
I have a message in to them already. I don't know if they verified for BRZ, but I'm not too far south from them.
|
08-14-2022, 10:15 PM | #25 |
Senior Member
Join Date: May 2012
Drives: 2013 Series 10 6MT FR-S
Location: Moreno Valley, CA
Posts: 5,560
Thanks: 2,010
Thanked 2,033 Times in 1,470 Posts
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
|
no rush to be honest. I am wondering if they will sell me the Mounting hardware from there adjustable splitter that ties into edge support and if it would work with the 2 piece.
__________________
2013 Series 10 FRS #553
RCE T2's, SPC LCAs -4/2.6 camber JDL 4-2-1 EL, FP and OP, Tuned by Zach@CSG on e85 RR Wilwood Front/Rear Sport BBK, Motul 600 Fluid ARC-8 17x9 SX2 GTs 245s/Koing 17x8 v730's 225's |
08-15-2022, 11:44 AM | #26 | |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,265
Thanks: 18,364
Thanked 16,460 Times in 7,451 Posts
Mentioned: 109 Post(s)
Tagged: 0 Thread(s)
|
Quote:
I would imagine it would fit. If you do notice that the rear part of the splitter is sagging get it off the car and fixed ASAP or it will start to warp it. I had to heat mine up and park the box truck on it over a weekend to get it somewhat flat again.
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
|
08-15-2022, 01:41 PM | #27 | |
Senior Member
Join Date: Dec 2015
Drives: Track preped NA FRS
Location: Montreal, Canada
Posts: 987
Thanks: 1,056
Thanked 681 Times in 405 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Also, I dont mount the splitter to the bumper. I mount it to the chassis, the bumper just happens to be above the splitter, resting on it. I assume anyone building a splitter would do the same. |
|
08-19-2022, 02:37 PM | #28 |
Senior Member
Join Date: May 2020
Drives: 22 BRZ limited
Location: Clarksville TN
Posts: 1,198
Thanks: 219
Thanked 1,004 Times in 530 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
What's in the box?
|
The Following User Says Thank You to dragoontwo For This Useful Post: | norcalpb (08-19-2022) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2022+ BRZ/GR86 specific oil cooler options | CSG Mike | Tracking / Autocross / HPDE / Drifting | 0 | 07-26-2022 07:25 PM |
GR86 In R7 of the Toyota Gazoo Racing GT Cup + GR86 coming to Grand Turismo Sport | Blighty | GR86 General Topics (2nd Gen 2022+ Toyota 86) | 37 | 07-18-2021 03:38 PM |
Downforce for an FR-S? | HachiRo | Cosmetic Modification (Interior/Exterior/Lighting) | 40 | 08-26-2014 10:24 PM |
Scion FR-S options:what options did you have dealer installed? | Scionshaun | Scion FR-S / Toyota 86 GT86 General Forum | 42 | 01-06-2014 01:35 AM |
Bushing upgrades, geometry options and other component options? | der_rainman | Suspension | Chassis | Brakes -- Sponsored by 949 Racing | 10 | 06-26-2013 12:53 PM |